Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › FRONT PASSENGER AIRBAG ASSEMBLY

FRONT PASSENGER AIRBAG ASSEMBLY > REMOVAL

for Preparation Click here



1. PRECAUTION

CAUTION:
Be sure to read "PRECAUTION" thoroughly before servicing (Click here).

NOTICE:
w/ Navigation System for HDD:
After the ignition switch is turned off, the navigation receiver assembly (HDD navigation system) records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 60 seconds before disconnecting the cable from the negative (-) battery terminal.



2. ALIGN FRONT WHEELS FACING STRAIGHT AHEAD


3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait for 90 seconds after disconnecting the cable to prevent airbag deployment.



4. REMOVE NO. 3 LOWER STEERING WHEEL COVER


    C141756
  1. Using a screwdriver, disengage the claw and remove the No. 3 lower steering wheel cover.

    HINT:
    Tape up the screwdriver tip before use.



5. REMOVE NO. 2 LOWER STEERING WHEEL COVER


    C141757
  1. Using a screwdriver, disengage the claw and remove the No. 2 lower steering wheel cover.

    HINT:
    Tape up the screwdriver tip before use.



6. REMOVE STEERING PAD


    C141758E02
  1. Using a "TORX" socket (T30), loosen the 2 "TORX" screws until the groove along the screw circumference catches on the screw case.



    C133859
  1. Pull out the steering pad from the steering wheel assembly and support the steering pad with one hand.

    NOTICE:
    When removing the steering pad, do not pull the airbag wire harness.

  1. Disconnect the horn connector from the steering pad.

  1. Disconnect the 2 airbag connectors and remove the steering pad.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Remove the steering pad.



7. REMOVE STEERING WHEEL ASSEMBLY
  1. Remove the steering wheel assembly set nut.

  1. Put matchmarks on the steering wheel assembly and the steering main shaft.

  1. Disconnect the connectors from the spiral cable.



    C132542E01
  1. Using SST, remove the steering wheel assembly.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05031)



8. REMOVE FRONT DOOR SCUFF PLATE LH


    B132067
  1. Disengage the 7 claws and 3 clips, and remove the front door scuff plate LH.



9. REMOVE COWL SIDE TRIM SUB-ASSEMBLY LH


    B132116E01
  1. Remove the cowl side trim clip.

  1. Disengage the 2 clips and remove the cowl side trim sub-assembly LH.



10. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL LH


    B147263E01
  1. Remove the bolt <A> and the screw <B>.

  1. Disengage the 2 claws and the DLC3.

  1. Disconnect the hood lock control cable assembly.

  1. Disengage the claw and the 4 clips.

  1. Remove the air hose, disconnect the connector, and then remove the lower instrument panel finish panel LH.



11. REMOVE STEERING COLUMN COVER


    C132544
  1. Remove the 2 screws.

  1. Disengage the 2 claws to remove the lower steering column cover.



    C139581
  1. Disengage the claw to remove the upper steering column cover.



12. REMOVE TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE
  1. Disconnect the connectors from the turn signal switch assembly with spiral cable sub-assembly.



    C132546
  1. Using pliers, grip the claws of the clamp and remove the turn signal switch assembly with spiral cable sub-assembly.



13. REMOVE NO. 1 INSTRUMENT PANEL SUB-ASSEMBLY


    B133986
  1. Disengage the 3 claws and the 2 clips.

  1. Disconnect each connector and remove the instrument panel sub-assembly.



14. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (w/o Entry and Start System)


    B144612
  1. Disengage the 2 claws and 2 clips, and then remove the lower instrument panel finish panel.



15. REMOVE LOWER INSTRUMENT PANEL FINISH PANEL (w/ Entry and Start System)


    B226061
  1. Disengage the 2 claws and 2 clips, and then remove the lower instrument panel finish panel.

  1. Disconnect the connector.



16. REMOVE INSTRUMENT CLUSTER FINISH PANEL NO.1


    B133985E01
  1. Remove the 2 clips.

  1. Disengage the guide and 4 claws and then remove the instrument cluster finish panel.



17. REMOVE COMBINATION METER ASSEMBLY


    B133987E01
  1. Remove the 4 screws <E>.

  1. Disconnect each connector and remove the combination meter assembly.



18. REMOVE FRONT DOOR SCUFF PLATE RH

HINT:
Use the same procedures for the RH side and the LH side.



19. REMOVE COWL SIDE TRIM SUB-ASSEMBLY RH

HINT:
Use the same procedures for the RH side and the LH side.



20. REMOVE INSTRUMENT PANEL NO. 2 UNDER COVER SUB-ASSEMBLY


    B133988E01
  1. Disengage the 4 claws.

  1. Disengage the 2 guides and remove the No. 2 under cover sub-assembly.



21. REMOVE LOWER INSTRUMENT PANEL SUB-ASSEMBLY
  1. Remove the bolt <A>.



    B133992E01
  1. Remove the 4 screws <B>.

  1. Disengage the 3 claws and 3 clips, and then remove the lower instrument panel sub-assembly.



22. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Automatic Transaxle)


    B226062
  1. Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.



23. REMOVE SHIFT LEVER KNOB SUB-ASSEMBLY (for Manual Transaxle)


    B137272
  1. Turn the shift lever knob counterclockwise and remove the shift lever knob sub-assembly.



24. REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    B226063
  1. Disengage the 2 clips and remove the No. 1 instrument cluster finish panel garnish.



25. REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH


    B226064
  1. Disengage the 2 clips and remove the No. 2 instrument cluster finish panel garnish.



26. REMOVE FLOOR SHIFT POSITION INDICATOR HOUSING SUB-ASSEMBLY (for Automatic Transaxle)


    B226065
  1. Disengage the 6 claws and the 3 clips, and then remove the floor shift position indicator housing sub-assembly.

  1. with Seat Heater System:

    1. Disconnect each connector.



27. REMOVE UPPER CONSOLE PANEL (for Manual Transaxle)


    B137274E01
  1. Open the lid of the upper console panel.

  1. Apply protective tape to the area shown in the illustration.



    B137275
  1. Using a moulding remover, disengage the 2 claws and the 5 clips, and then remove the upper console panel as shown in the illustration.

  1. with Seat Heater System:

    1. Disconnect each connector.



28. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Automatic Transaxle)


    B226097
  1. Disengage the 3 claws and the 5 clips.

  1. Disconnect the connector and remove the upper console rear panel sub-assembly.



29. REMOVE UPPER CONSOLE REAR PANEL SUB-ASSEMBLY (for Manual Transaxle)


    B137277
  1. Disengage the 3 claws and the 5 clips, and remove the upper console rear panel sub-assembly.



30. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY


    B133997E01
  1. Remove the 2 screws <F>.

  1. Disengage the 4 claws.

  1. Disconnect each connector and remove the upper console panel sub-assembly.

    HINT:
    Set the shift lever in the D position.



31. REMOVE INSTRUMENT PANEL NO. 2 REGISTER ASSEMBLY


    B133998E01
  1. Apply protective tape to the areas shown in the illustration.



    B144610
  1. Using a moulding remover, disengage the 3 clips.



    B144611
  1. Using a moulding remover, disengage the 4 clips.

  1. Disconnect the connector and remove the instrument panel No. 2 register assembly.



32. REMOVE RADIO TUNER OPENING COVER WITH HEATER CONTROL PANEL ASSEMBLY (w/o Radio Receiver)


    B137278E01
  1. Remove the 4 bolts <N>.

  1. Disengage the 6 clips and remove the radio tuner opening cover with heater control panel assembly.

  1. Disconnect the connector.



33. REMOVE RADIO RECEIVER WITH HEATER CONTROL PANEL ASSEMBLY (w/ Radio Receiver)


    E131401
  1. Remove the 4 bolts.

  1. Pull the radio receiver with heater control panel assembly toward the rear of the vehicle and disengage the 4 clips.

  1. Disconnect each connector and remove the radio receiver with heater control panel assembly.



34. REMOVE NAVIGATION RECEIVER WITH HEATER CONTROL PANEL ASSEMBLY (w/ Navigation System)


    E129205
  1. Remove the 4 bolts.

  1. Pull the navigation receiver with heater control panel assembly toward the rear of the vehicle and disengage the 4 clips.

  1. Disconnect each connector and remove the navigation receiver with heater control panel assembly.



35. REMOVE CONSOLE BOX POCKET
  1. Remove the console box pocket.



36. REMOVE CONSOLE BOX CARPET


    B134004
  1. Remove the console box carpet.



37. REMOVE CONSOLE BOX ASSEMBLY


    B134002E01
  1. Remove the 2 screws <F>.



    B134003E01
  1. Remove the 2 bolts <G> and the console box assembly.



38. REMOVE NO. 2 CONSOLE BOX INSERT FRONT


    B134005E01
  1. Remove the 3 screws <F>.

  1. Disengage the clip and remove the No. 2 console box insert front.



39. REMOVE NO. 1 CONSOLE BOX INSERT FRONT


    B134006E01
  1. Remove the 3 screws <F>.

  1. Disengage the clip and remove the No. 1 console box insert front.



40. REMOVE FRONT PILLAR GARNISH LH


    B132056E01
  1. Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

  1. Cut off the clip <A>.

  1. Disengage the 2 claws and remove the front pillar garnish LH.

  1. Remove the clip <A> from the vehicle body.



    B132100E01
  1. Protect the curtain shield airbag assembly.

    1. Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.



41. REMOVE INSTRUMENT PANEL NO. 1 REGISTER ASSEMBLY


    B134007
  1. Disengage the 4 clips and remove the instrument panel No. 1 register assembly.



42. REMOVE INSTRUMENT PANEL NO. 1 SPEAKER PANEL SUB-ASSEMBLY


    B134009E01
  1. Disengage the 6 claws and the 2 clips.

  1. Disengage the 2 guides and remove the instrument panel No. 1 speaker panel sub-assembly.



43. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for LH Side)


    E129167
  1. Remove the 2 bolts and front No. 2 speaker assembly.

  1. Disconnect the connector.



44. REMOVE FRONT PILLAR GARNISH RH


    B132055E01
  1. Pull the upper part of the garnish toward the inside of the cabin and disengage the 2 clips.

  1. Cut off the clip <A>.

  1. Disengage the 2 claws and remove the front pillar garnish RH.

  1. Remove the clip <A> from the vehicle body.



    B132099E01
  1. Protect the curtain shield airbag assembly.

    1. Cover the airbag with a 700 mm (27.56 in.) x 120 mm (4.72 in.) cloth or piece of nylon and fix the ends of the cover with tape, as shown in the illustration.

      NOTICE:
      Cover the curtain shield airbag with a protective cover as soon as the front pillar garnish is removed.



45. REMOVE INSTRUMENT PANEL NO. 3 REGISTER ASSEMBLY


    B134008
  1. Disengage the 4 clips and remove the instrument panel No. 3 register assembly.



46. REMOVE INSTRUMENT PANEL NO. 2 SPEAKER PANEL SUB-ASSEMBLY


    B134010E01
  1. Disengage the 6 claws and the 2 clips.

  1. Disengage the 2 guides and remove the instrument panel No. 2 speaker panel sub-assembly.



47. REMOVE FRONT NO. 2 SPEAKER ASSEMBLY (for RH Side)

HINT:
Use the same procedures for the RH side and the LH side .



48. REMOVE NO. 1 DEFROSTER NOZZLE GARNISH


    B134011E01
  1. Disengage the 8 clips and the 4 guides.

  1. Disconnect each connector and remove the No. 1 defroster nozzle garnish.



49. DISCONNECT INSTRUMENT PANEL WIRE ASSEMBLY


    C132564E01
  1. Disconnect the connector (yellow colored one).



50. REMOVE INSTRUMENT PANEL SAFETY PAD ASSEMBLY
  1. Disengage each clamp.

  1. Disconnect each connector.

  1. Remove the bolt <J>.

  1. Remove the 2 passenger airbag bolts <K>.



  1. with Plasmacluster:



    1. Disconnect the connector.


      B134012E04

  1. Remove the 2 bolts <H> or <O>.

  1. Remove the 2 nuts <C> or <I>.



  1. Disengage the 5 claws and remove the instrument panel safety pad assembly.


    B134014E04



51. REMOVE FRONT PASSENGER AIRBAG ASSEMBLY


    C132565
  1. Remove the 2 screws.



    C132566
  1. Disengage the 10 hooks and remove the front passenger airbag assembly from the instrument panel safety pad assembly.



52. REMOVE INSTRUMENT PANEL WIRE ASSEMBLY


    C132567
  1. Disconnect the 2 connectors.

  1. Remove the clamp and the instrument panel wire assembly from the front passenger airbag assembly.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.