Home › BODY › SEAT › FRONT SEAT ASSEMBLY (for Power Seat)

FRONT SEAT ASSEMBLY (for Power Seat) > DISASSEMBLY

for Preparation Click here


CAUTION:
Wear protective gloves. Sharp areas on the seat frame and adjuster may injure your hands.



1. REMOVE RECLINING POWER SEAT SWITCH KNOB


    B134671
  1. Using a screwdriver, detach the reclining power seat switch knob.

    HINT:
    Tape the screwdriver tip before use.



2. REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


    B134672
  1. Using a screwdriver, detach the slide and vertical power seat switch knob.

    HINT:
    Tape the screwdriver tip before use.



3. REMOVE FRONT SEAT CUSHION SHIELD ASSEMBLY


    B134678
  1. Disconnect the 2 hooks.



    B134673
  1. Remove the 5 screws.

  1. Disengage the claw and separate the front seat cushion shield assembly.

  1. Disconnect the connector from the front power seat lumbar switch.



4. REMOVE FRONT INNER NO. 1 SEAT CUSHION SHIELD


    B134674
  1. Remove the screw.

  1. Detach the 2 claws and remove the front inner No. 1 seat cushion shield.



5. REMOVE FRONT LUMBAR POWER SEAT SWITCH


    B134675
  1. Remove the 2 screws and front lumbar power seat switch.



6. REMOVE FRONT SEAT INNER BELT ASSEMBLY


    B132033E01
  1. for Driver seat:

    1. Disconnect the connectors and disengage the 4 clamps.

  1. for Passenger seat:

    1. Disconnect the connector and disengage the 3 clamps.



    B132034
  1. Remove the nut and front seat inner belt assembly.



7. REMOVE FRONT INNER SEAT CUSHION SHIELD


    B134676
  1. Remove the screw.

  1. Using a clip remover, detach the clip.

  1. Using a screwdriver, detach the claw and remove the front inner seat cushion shield.

    HINT:
    Tape the screwdriver tip before use.



8. REMOVE LOWER SEAT TRACK SPACER


    B134698E01
  1. Remove the 2 screws and lower seat track spacer.



9. REMOVE FRONT POWER SEAT SWITCH


    B134677
  1. Remove the 3 screws.

  1. Disconnect the connector and remove the front power seat switch.



10. REMOVE FRONT SEPARATE TYPE SEAT CUSHION COVER WITH PAD


    B134679E01
  1. Disconnect the 2 clamps.

  1. Remove the 4 hooks.



    B134680
  1. Using a screwdriver, detach the hooks and remove the front separate type seat cushion cover with pad.



11. REMOVE FRONT SEPARATE TYPE SEAT CUSHION COVER


    B134681E01
  1. Remove the 16 hog rings and front separate type seat cushion cover from the front separate type seat cushion pad.



12. REMOVE FRONT SEATBACK BOARD SUB-ASSEMBLY


    B134682E01
  1. Remove the 2 screws.

  1. Disconnect the 14 clamps and front separate type seatback cover.

  1. Pull the seatback board in the direction indicated by the arrow in the illustration to detach the 2 claws. Then, remove the seatback board.



13. REMOVE FRONT SEAT HEADREST SUPPORT


    B134683
  1. Detach the 2 claws and remove the headrest support.



14. REMOVE FRONT SEAT HEADREST SUPPORT


15. REMOVE FRONT SEPARATE TYPE SEATBACK COVER WITH PAD


    B134684E01
  1. Remove the 2 hog rings and 3 hooks.



    B134685
  1. Remove the nut and 2 seatback cover brackets.

  1. Remove the front separate type seatback cover with pad.



16. REMOVE FRONT SEPARATE TYPE SEATBACK COVER


    B134686E01
  1. Remove the 10 hog rings and front separate type seatback cover from the front separate type seatback pad.



17. REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY


    B134693
  1. Disconnect the connector.

  1. Remove the 2 screws and lumbar support adjuster assembly.



18. REMOVE FRONT SEAT SIDE AIRBAG ASSEMBLY


    B233420E01
  1. Disconnect the 4 wire harness clamps from under the seat.



    B233421E01
  1. Disconnect the 2 clamps.

  1. Remove the 2 nuts and the front seat side airbag assembly.

    CAUTION:
    1. The nuts must not be reused.
    2. Make sure that the seat frame assembly is not deformed. If it is, replace it with a new one.



19. REMOVE RECLINING ADJUSTER INSIDE COVER RH
  1. Disconnect the harness.



    B134687
  1. Remove the 2 screws and reclining adjuster inside cover RH.



20. REMOVE RECLINING ADJUSTER INSIDE COVER LH
  1. Disconnect the harness.



    B134688
  1. Remove the 2 screws and reclining adjuster inside cover LH.



21. REMOVE SEAT RECLINING ADJUSTER INSIDE COVER RH


    B134689
  1. Remove the screw.

  1. Detach the claw and remove the seat reclining adjuster inside cover RH.



22. REMOVE SEAT RECLINING ADJUSTER INSIDE COVER LH


    B134690
  1. Remove the screw.

  1. Detach the claw and remove the seat reclining adjuster inside cover LH.



23. REMOVE FRONT LOWER SEAT CUSHION SHIELD LH


    B134692
  1. Remove the screw and detach the hook of the front lower seat cushion shield LH.



24. REMOVE FRONT LOWER SEAT CUSHION SHIELD


25. REMOVE SEAT POSITION SENSOR (for Driver Side)


    C133891
  1. Disconnect the connector.

  1. Using a "TORX" socket (T30), remove the "TORX" screw and seat position sensor with the seat slide position sensor protector.



    C133892
  1. Remove the seat position sensor from the seat slide position sensor protector as shown in the illustration.



26. REMOVE FRONT SEAT WIRE