Home › RESTRAINTS › SUPPLEMENTAL RESTRAINT SYSTEM › FRONT SEAT SIDE AIRBAG ASSEMBLY (for Power Seat)

FRONT SEAT SIDE AIRBAG ASSEMBLY (for Power Seat) > REMOVAL

for Preparation Click here


CAUTION:
  1. Be sure to read Precaution thoroughly before servicing (Click here).
  2. If the side airbag was deployed, replace the front seat assembly with a new one.



1. REMOVE FRONT SEAT HEADREST ASSEMBLY


2. REMOVE SEAT TRACK COVER
  1. Operate the power seat switch knob and move the seat to the position farthest forward.



    B139099
  1. Using a screwdriver, detach the 4 claws and remove the seat track cover.

    HINT:
    Tape the screwdriver tip before use.



3. REMOVE INNER SEAT TRACK BRACKET COVER


    B139100
  1. Using a screwdriver, detach the 4 claws and remove the inner seat track bracket cover.



4. REMOVE FRONT SEAT ASSEMBLY
  1. Operate the power seat switch knob and move the seat to the rearmost position.



    B140607
  1. Remove the 2 bolts on the front seat track bracket.

  1. Operate the power seat switch knob and move the seat to the position farthest forward.



    B139102
  1. Remove the 2 bolts on the rear seat track bracket.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to prevent the airbag and seat belt pretensioner from deploying (Click here).

  1. Disconnect the connectors under the seat. Then remove the front seat assembly.



5. REMOVE RECLINING POWER SEAT SWITCH KNOB


    B134671
  1. Using a screwdriver, detach the reclining power seat switch knob.

    HINT:
    Tape the screwdriver tip before use.



6. REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB


    B134672
  1. Using a screwdriver, detach the slide and vertical power seat switch knob.

    HINT:
    Tape the screwdriver tip before use.



7. REMOVE FRONT SEAT CUSHION SHIELD ASSEMBLY


    B134678
  1. Disconnect the 2 hooks.



    B134673
  1. Remove the 5 screws.

  1. Disengage the claw and separate the front seat cushion shield assembly.

  1. Disconnect the connector from the front power seat lumbar switch.



8. REMOVE FRONT SEAT INNER BELT ASSEMBLY


    B132033E01
  1. for Driver seat:

    1. Disconnect the connectors and disengage the 4 clamps.

  1. for Passenger seat:

    1. Disconnect the connector and disengage the 3 clamps.



    B132034
  1. Remove the nut and front seat inner belt assembly.



9. REMOVE FRONT INNER SEAT CUSHION SHIELD


    B134676
  1. Remove the screw.

  1. Using a clip remover, detach the clip.

  1. Using a screwdriver, detach the claw and remove the front inner seat cushion shield.

    HINT:
    Tape the screwdriver tip before use.



10. REMOVE FRONT SEAT BACK BOARD SUB-ASSEMBLY


    B134682E01
  1. Remove the 2 screws.

  1. Disconnect the 14 clamps and front separate type seatback cover.

  1. Pull the seatback board in the direction indicated by the arrow in the illustration to detach the 2 claws. Then, remove the seatback board.



11. REMOVE FRONT SEAT HEADREST SUPPORT (for LH Side)


    B134683
  1. Detach the 2 claws and remove the headrest support.



12. REMOVE FRONT SEAT HEADREST SUPPORT (for RH Side)


13. REMOVE FRONT SEPARATE TYPE SEAT BACK ASSEMBLY


    B134684E01
  1. Remove the 2 hog rings and 3 hooks.



    B134685
  1. Remove the nut and 2 seatback cover brackets.

  1. Remove the front separate type seatback cover with pad.



14. REMOVE FRONT SEAT SIDE AIRBAG ASSEMBLY


    B233420E01
  1. Disconnect the 4 wire harness clamps from under the seat.



    B233421E01
  1. Disconnect the 2 clamps.

  1. Remove the 2 nuts and the front seat side airbag assembly.

    CAUTION:
    1. The nuts must not be reused.
    2. Make sure that the seat frame assembly is not deformed. If it is, replace it with a new one.