DTC P0443 Evaporative Emission Control System Purge Control Valve Circuit |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0443 | Terminal voltage of ECM output circuit does not correspond with drive signals from ECM to purge VSV (1 trip detection logic) |
|

| 1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE PURGE VSV CONTROL) |
![]() |
Connect the intelligent tester to the DLC3.
Remove the vacuum hose of the purge VSV from the charcoal canister.
Start the engine and turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.
When the purge VSV is operated using the intelligent tester, check whether the disconnected hose applies suction to your finger.
| Tester Operation | Specified Condition |
| VSV is ON | Disconnected hose applies suction to finger |
| VSV is OFF | Disconnected hose applies no suction to finger |
|
| ||||
| NG | |
| 2.INSPECT PURGE VSV |
![]() |
Disconnect the C6 purge VSV connector.
Measure the resistance between the terminals of the purge VSV.
Reconnect the purge VSV connector.
|
| ||||
| OK | |
| 3.INSPECT PURGE VSV (POWER SOURCE VOLTAGE) |
![]() |
Disconnect the C6 purge VSV connector.
Turn the ignition switch to the ON position.
Measure the voltage between the terminal of the wire harness side connector and body ground.
| Tester Connection | Specified Condition |
| Purge VSV (C6-1) - Body ground | 9 to 14 V |
Reconnect the purge VSV connector.
|
| ||||
| NG | |
| 4.INSPECT ENGINE ROOM J/B (EFI RELAY, EFI MAIN FUSE) |
![]() |
Inspect the EFI MAIN fuse.
Remove the EFI MAIN fuse from the engine room J/B.
Measure the EFI MAIN fuse resistance.
Reinstall the EFI MAIN fuse.
Inspect the EFI relay.
Remove the engine room J/B from the engine room R/B.
Measure the EFI relay resistance.
| Tester Connection | Specified Condition |
| 1E-6 - 1E-12 | 10 kΩ or higher |
| Below 1 Ω (Apply battery voltage between terminals 1E-9 and 1E-11) |
Reinstall the engine room J/B.
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (PURGE VSV - EFI RELAY) |
![]() |
Inspect the EFI No. 3 fuse.
Remove the EFI No. 3 fuse from the engine room J/B.
Measure the EFI No. 3 fuse resistance.
Reinstall the EFI No. 3 fuse.
Disconnect the C6 purge VSV connector.
Remove the engine room J/B from the engine room R/B.
Disconnect the 1E engine room J/B connector.
Measure the resistance between the terminals.
| Tester Connection | Specified Condition |
| Purge VSV (C6-1) - Engine room R/B (1E-6) | Below 1 Ω |
| Tester Connection | Specified Condition |
| Purge VSV (C6-1) or Engine room R/B (1E-6) - Body ground | 10 kΩ or higher |
Reconnect the purge VSV connector.
Reconnect the engine room J/B connector.
Reinstall the engine room J/B.
|
| ||||
| OK | ||
| ||
| 6.CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM) |
![]() |
Disconnect the C6 purge VSV connector.
Disconnect the C24 ECM connector.
Measure the resistance between the terminals of the wire harness side connectors.
| Tester Connection | Specified Condition |
| Purge VSV (C6-2) - PRG (C24-49) | Below 1 Ω |
| Tester Connection | Specified Condition |
| Purge VSV (C6-2) or PRG (C24-49) - Body ground | 10 kΩ or higher |
Reconnect the purge VSV connector.
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||