DTC P0705 Transmission Range Sensor Circuit Malfunction (PRNDL Input) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0705 | (A) Any 2 or more signals of the following are ON simultaneously (2-trip detection logic):
|
|

| READ DATA LIST |
Turn the ignition switch off.
Connect the intelligent tester together with the CAN VIM (controller area network vehicle interface module) to the DLC3.
Turn the ignition switch to the ON position.
Turn on the tester.
Select the item "Powertrain / Engine / Data List".
According to the display on the tester, read the "DATA LIST".
| Item | Measurement Item / Range (Display) | Normal Condition | Diagnostic Note |
| Neutral Position SW Signal | PNP SW Status / ON or OFF | Shift lever position is; P and N: ON Except P or N: OFF | When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect. |
| Shift SW status (R Range) | PNP SW Status / ON or OFF | Shift lever position is; R: ON Except R: OFF | ↑ |
| Shift SW status (D Range) | PNP SW Status / ON or OFF | Shift lever position is; D and S: ON Except D or S: OFF | ↑ |
| 1.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH) |
![]() |
Disconnect the park / neutral position switch connector.
Turn the ignition switch to the ON position.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| 1 - Body ground | 10 to 14 V |
|
| ||||
| OK | |
| 2.CHECK ECM (OUTPUT SIGNAL) |
![]() |
Turn the ignition switch to the ON position.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| 4 - Body ground | Below 2 V |
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ST RELAY) |
![]() |
Disconnect the C1 park/neutral position switch connector.
Remove the ST relay from the engine room relay block.
Measure the resistance between the terminals.
| Tester Connection | Specified Condition |
| L (C1-9) - ST relay terminal 1 | Below 1 Ω |
Reconnect the park/neutral position switch connector.
Install the ST relay.
|
| ||||
| OK | |
| 4.INSPECT ST RELAY |
![]() |
Remove the ST relay from the engine room relay block.
Measure the resistance between the terminals.
| Tester Connection | Specified Condition |
| 3 - 5 | 10 kΩ or higher |
| 3 - 5 | Below 1 Ω Apply battery voltage between terminals 1 and 2 |
Install the ST relay.
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND) |
![]() |
Remove the ST relay from the engine room relay block.
Measure the resistance between the terminals
| Tester Connection | Specified Condition |
| ST relay terminal 2 - Body ground | Below 1 Ω |
Install the ST relay.
|
| ||||
| OK | |
| 6.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY |
![]() |
Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.
| Shift Position | Tester Connection | Specified Condition |
| P | 2 - 6 and 4 - 5 | Below 1 Ω |
| Except P | 10 kΩ or higher | |
| R | 2 - 1 | Below 1 Ω |
| Except R | 10 kΩ or higher | |
| N | 2 - 9 and 4 - 5 | Below 1 Ω |
| Except N | 10 kΩ or higher | |
| D, S, ''+'' and ''-'' | 2 - 7 | Below 1 Ω |
| Except D, S, ''+'' and ''-'' | 10 kΩ or higher |
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR |
![]() |
Connect the park/neutral position switch connector.
Disconnect the ECM connectors.
Turn the ignition switch to the ON position, and measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.
| Shift Position | Tester Connection | Specified Condition |
| P | C58-24*1 (P) - Body ground C55-24*2 (P) - Body ground | 10 to 14 V |
| Except P | Below 1 V | |
| N | C58-27*1 (N) - Body ground C55-27*2 (N) - Body ground | 10 to 14 V |
| Except N | Below 1 V | |
| R | C58-25*1 (R) - Body ground C55-25*2 (R) - Body ground | 10 to 14 V*3
|
| Except R | Below 1 V | |
| D and S | C58-26*1 (D) - Body ground C55-26*2 (D) - Body ground | 10 to 14 V |
| Except D and S | Below 1 V | |
| S, ''+'' and ''-'' | A24-25*1 (S) - Body ground A55-25*2 (S) - Body ground | 10 to 14 V |
| Except S, ''+'' and ''-'' | Below 1 V |
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR |
![]() |
Disconnect the transmission control switch connector of the shift lock control unit assembly.
Turn the ignition switch to the ON position.
Measure the voltage between the terminals.
| Tester Connection | Specified Condition |
| 3 - Body ground | 10 to 14 V |
Reconnect the transmission control switch connector.
|
| ||||
| OK | |
| 9.INSPECT TRANSMISSION CONTROL SWITCH |
![]() |
Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.
| Shift Position | Tester Connection | Specified Condition |
| S, ''+'' and ''-'' | 3 - 7 | Below 1 Ω |
| Except S, ''+'' and ''-'' | 10 kΩ or higher |
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR |
![]() |
Connect the park/neutral position switch connector.
Disconnect the ECM connectors.
Turn the ignition switch to the ON position, and measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.
| Shift Position | Tester Connection | Specified Condition |
| P | C58-24*1 (P) - Body ground C55-24*2 (P) - Body ground | 10 to 14 V |
| Except P | Below 1 V | |
| N | C58-27*1 (N) - Body ground C55-27*2 (N) - Body ground | 10 to 14 V |
| Except N | Below 1 V | |
| R | C58-25*1 (R) - Body ground C55-25*2 (R) - Body ground | 10 to 14 V*3
|
| Except R | Below 1 V | |
| D and S | C58-26*1 (D) - Body ground C55-26*2 (D) - Body ground | 10 to 14 V |
| Except D and S | Below 1 V | |
| S, ''+'' and ''-'' | A24-25*1 (S) - Body ground A55-25*2 (S) - Body ground | 10 to 14 V |
| Except S, ''+'' and ''-'' | Below 1 V |
|
| ||||
| OK | ||
| ||
| 11.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM) |
![]() |
Disconnect the ECM connectors.
Turn the ignition switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| B (C1-4) - NSW (C58-62) | Below 1 Ω |
| Tester Connection | Specified Condition |
| B (C1-4) - NSW (C55-62) | Below 1 Ω |
| Tester Connection | Specified Condition |
| B (C1-4) or NSW (C58-62) - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| B (C1-4) or NSW (C55-62) - Body ground | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||