Home › ENGINE · 2GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0705    Transmission Range Sensor Circuit Malfunction (PRNDL Input)

for Preparation Click here


DESCRIPTION

The park/neutral position switch detects the shift lever position and sends signals to the ECM.

DTC No.
DTC Detection Condition
Trouble Area
P0705
(A) Any 2 or more signals of the following are ON simultaneously (2-trip detection logic):
  1. P input signal
  2. N input signal.
  3. R input signal
  4. D input signal
(B) Any 2 or more signals of the following are ON simultaneously (2-trip detection logic):
  1. NSW input signal
  2. R input signal
  3. D input signal
(C) Any of following conditions is met for 2.0 sec. or more with the shift lever in the S position (2-trip detection logic).
  1. NSW input signal is ON.
  2. P input signal is ON.
  3. N input signal is ON.
  4. R input signal is ON.
(D) All switches are OFF simultaneously for NSW, P, R, N and D.
  1. Short in park/neutral position switch circuit
  2. Park/neutral position switch
  3. ECM

WIRING DIAGRAM


A143786E05


INSPECTION PROCEDURE

HINT:
According to the DATA LIST displayed on the intelligent tester, you can read the values of the switches, sensors, actuators and so on without parts removal. Reading the DATA LIST as the first step in troubleshooting is one method to shorten labor time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


READ DATA LIST
  1. Turn the engine switch off.

  2. Connect the intelligent tester together to the DLC3.

  3. Turn the engine switch on (IG).

  4. Turn the tester on.

  5. Select the item "Powertrain / Engine / Data List".

  6. According to the display on the tester, read the "DATA LIST".

    Item
    Measurement Item / Range (Display)
    Normal Condition
    Diagnostic Note
    Neutral Position SW Signal
    PNP SW Status / ON or OFF
    Shift lever position is;
    P and N: ON
    Except P or N: OFF
    When the shift lever position displayed on the intelligent tester differs from the actual position, adjustment of the PNP switch or the shift cable may be incorrect.
    Shift SW status (R Range)
    PNP SW Status / ON or OFF
    Shift lever position is;
    R: ON
    Except R: OFF
    ↑
    Shift SW status (D Range)
    PNP SW Status / ON or OFF
    Shift lever position is;
    D and S: ON
    Except D or S: OFF
    ↑

1.CHECK HARNESS AND CONNECTOR (BATTERY - PARK/NEUTRAL POSITION SWITCH)


    C117645E12
  1. Disconnect the park/neutral position switch connector.

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Specified Condition
    RB (C1-1) - Body ground
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK ECM (OUTPUT SIGNAL)


    C117645E12
  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Specified Condition
    B (C1-4) - Body ground
    Below 2 V



NG
Go to step 11
OK


3.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ST RELAY)


    A137047E18
  1. Disconnect the C1 park/neutral position switch connector.

  1. Remove the ST relay from the engine room relay block.

  1. Measure the resistance between the terminals.

    Standard resistance:
    Tester Connection
    Specified Condition
    L (C1-9) - ST relay terminal 1
    Below 1 Ω

  1. Reconnect the park/neutral position switch connector.

  1. Install the ST relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT ST RELAY


    B016200E02
  1. Remove the ST relay from the engine room relay block.

  1. Measure the resistance between the terminals.

    Standard resistance:
    Tester Connection
    Specified Condition
    3 - 5
    10 kΩ or higher
    3 - 5
    Below 1 Ω
    Apply battery voltage between terminals 1 and 2

  1. Install the ST relay.



NG
REPLACE ST RELAY
OK


5.CHECK HARNESS AND CONNECTOR (ST RELAY - BODY GROUND)


    A137046E01
  1. Remove the ST relay from the engine room relay block.

  1. Measure the resistance between the terminals.

    Standard resistance:
    Tester Connection
    Specified Condition
    ST relay terminal 2 - Body ground
    Below 1 Ω

  1. Install the ST relay.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    C110340E51
  1. Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

    Standard resistance:
    Shift Position
    Tester Connection
    Specified Condition
    P
    2 - 6 and 4 - 5
    Below 1 Ω
    Except P
    10 kΩ or higher
    R
    2 - 1
    Below 1 Ω
    Except R
    10 kΩ or higher
    N
    2 - 9 and 4 - 5
    Below 1 Ω
    Except N
    10 kΩ or higher
    D, S, ''+'' and ''-''
    2 - 7
    Below 1 Ω
    Except D, S, ''+'' and ''-''
    10 kΩ or higher



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)
OK


7.CHECK HARNESS AND CONNECTOR


    C136857E18
  1. Connect the park/neutral position switch connector.

  1. Disconnect the ECM connectors.

  1. Turn the engine switch on (IG), and measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.

    Standard voltage:

    Shift Position
    Tester Connection
    Specified Condition
    P
    C58-24*1 (P) - Body ground
    C55-24*2 (P) - Body ground
    10 to 14 V
    Except P
    Below 1 V
    N
    C58-27*1 (N) - Body ground
    C55-27*2 (N) - Body ground
    10 to 14 V
    Except N
    Below 1 V
    R
    C58-25*1 (R) - Body ground
    C55-25*2 (R) - Body ground
    10 to 14 V*3
    Except R
    Below 1 V
    D and S
    C58-26*1 (D) - Body ground
    C55-26*2 (D) - Body ground
    10 to 14 V
    Except D and S
    Below 1 V
    S, ''+'' and ''-''
    A24-25*1 (S) - Body ground
    A55-25*2 (S) - Body ground
    10 to 14 V
    Except S, ''+'' and ''-''
    Below 1 V

    HINT:
    *1: RHD
    *2: LHD
    *3: The voltage will drop slightly due to lighting up of the back up light.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK HARNESS AND CONNECTOR


    C110345E21
  1. Disconnect the transmission control switch connector of the shift lock control unit assembly.

  1. Turn the engine switch on (IG).

  1. Measure the voltage between the terminals.

    Standard voltage:
    Tester Connection
    Specified Condition
    3 - Body ground
    10 to 14 V

  1. Reconnect the transmission control switch connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


9.INSPECT TRANSMISSION CONTROL SWITCH


    C136860E04
  1. Measure the resistance according to the value(s) in the table below when the shift lever is moved to each position.

    Standard resistance:
    Shift Position
    Tester Connection
    Specified Condition
    S, ''+'' and ''-''
    3 - 7
    Below 1 Ω
    Except S, ''+'' and ''-''
    10 kΩ or higher



NG
REPLACE TRANSMISSION CONTROL SWITCH
OK


10.CHECK HARNESS AND CONNECTOR


    C136857E19
  1. Connect the park/neutral position switch connector.

  1. Disconnect the ECM connectors.

  1. Turn the engine switch on (IG), and measure the voltage according to the value(s) in the table below when the shift lever is moved to each position.

    Standard voltage:

    Shift Position
    Tester Connection
    Specified Condition
    P
    C58-24*1 (P) - Body ground
    C55-24*2 (P) - Body ground
    10 to 14 V
    Except P
    Below 1 V
    N
    C58-27*1 (N) - Body ground
    C55-27*2 (N) - Body ground
    10 to 14 V
    Except N
    Below 1 V
    R
    C58-25*1 (R) - Body ground
    C55-25*2 (R) - Body ground
    10 to 14 V*3
    Except R
    Below 1 V
    D and S
    C58-26*1 (D) - Body ground
    C55-26*2 (D) - Body ground
    10 to 14 V
    Except D and S
    Below 1 V
    S, ''+'' and ''-''
    A24-25*1 (S) - Body ground
    A55-25*2 (S) - Body ground
    10 to 14 V
    Except S, ''+'' and ''-''
    Below 1 V

    HINT:
    *1: RHD
    *2: LHD
    *3: The voltage will drop slightly due to lighting up of the back up light.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

11.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH - ECM)


    C136861E28
  1. Disconnect the C58 (RHD) or C55 (LHD) ECM connector.

  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    RHD:
    Tester Connection
    Specified Condition
    B (C1-4) - NSW (C58-62)
    Below 1 Ω
    LHD:
    Tester Connection
    Specified Condition
    B (C1-4) - NSW (C55-62)
    Below 1 Ω


    Standard resistance (Check for short):
    RHD:
    Tester Connection
    Specified Condition
    B (C1-4) or NSW (C58-62) - Body ground
    10 kΩ or higher
    LHD:
    Tester Connection
    Specified Condition
    B (C1-4) or NSW (C55-62) - Body ground
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)