STEERING COLUMN ASSEMBLY > INSTALLATION |
| 1. INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY |
Align the matchmarks on the steering intermediate shaft assembly and the steering column assembly.
![]() |
Install the bolt.
| 2. INSTALL STEERING COLUMN ASSEMBLY |
![]() |
Install the steering column assembly with the bolt and 2 nuts.
Connect the connectors and wire harness clamps to the steering column assembly.
![]() |
Align the matchmarks on the steering intermediate shaft assembly and the power steering link assembly.
![]() |
Install the bolt.
![]() |
Install the clamp to the steering column hole shield.
| 3. INSTALL NO. 1 AIR DUCT |
![]() |
Engage the 2 claws to install the No. 1 air duct.
| 4. TURN FRONT WHEELS TO FACE STRAIGHT AHEAD |
| 5. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY |
![]() |
Install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly with the clamp.
Connect the connectors to the turn signal switch assembly with spiral cable sub-assembly.
| 6. INSTALL STEERING COLUMN COVER |
![]() |
Engage the claw to install the upper steering column cover.
![]() |
Engage the 2 claws to install the lower steering column cover.
Install the 2 screws.
| 7. ADJUST SPIRAL CABLE SUB-ASSEMBLY |
Check that the ignition switch is off.
Check that the battery negative (-) cable is disconnected.
![]() |
Rotate the spiral cable counterclockwise slowly by hand until it feels firm.
![]() |
Rotate the spiral cable clockwise approximately 2.5 turns to align the marks.
| 8. INSTALL STEERING WHEEL ASSEMBLY |
![]() |
Align the matchmarks on the steering wheel assembly and steering main shaft.
Install the steering wheel assembly set nut.
Connect the connectors to the spiral cable sub-assembly.
| 9. INSPECT STEERING WHEEL CENTER POINT |
| 10. INSTALL STEERING PAD |
Check that the ignition switch is off.
Check that the battery negative (-) terminal is disconnected.
![]() |
Support the steering pad with one hand.
Connect the 2 airbag connectors to the steering pad.
Connect the horn connector to the steering pad.
Confirm that the circumference groove of the "TORX" screw fits in the screw case, and place the steering pad onto the steering wheel assembly.
![]() |
Using a "TORX" socket (T30), tighten the 2 "TORX" screws.
| 11. INSTALL NO. 3 LOWER STEERING WHEEL COVER |
![]() |
Engage the claw and install the No. 3 lower steering wheel cover.
| 12. INSTALL NO. 2 LOWER STEERING WHEEL COVER |
![]() |
Engage the claw and install the No. 2 lower steering wheel cover.
| 13. INSTALL LOWER INSTRUMENT PANEL FINISH PANEL LH |
![]() |
Install the air hose and connect the connector.
Engage the 2 claws and the DLC3.
Engage the claw and the 4 clips.
Instal the lower instrument panel finish panel LH with the screw <B> and bolt <A>.
| 14. INSTALL COWL SIDE TRIM SUB-ASSEMBLY LH |
![]() |
Engage the 2 clips.
Install the cowl side trim sub-assembly LH with the cowl side trim clip.
| 15. INSTALL FRONT DOOR SCUFF PLATE LH |
![]() |
Engage the 7 claws and 3 clips, then install the front door scuff plate LH.
| 16. INSTALL FRONT WHEEL LH |
| 17. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 18. INSPECT STEERING PAD |
![]() |
With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one:
Make sure that the horn sounds.
| 19. INSPECT SRS WARNING LIGHT |