DTC P0031 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1) |
DTC P0032 Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1) |
DTC P0051 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 2 Sensor 1) |
DTC P0052 Oxygen (A/F) Sensor Heater Control Circuit High (Bank 2 Sensor 1) |


| DTC No. | DTC Detection Condition | Trouble Area |
| P0031 P0051 | Air-Fuel Ratio (A/F) sensor heater (bank 1, 2, sensor 1) current is less than 0.8 A (1 trip detection logic) |
|
| P0032 P0052 | Air-Fuel Ratio (A/F) sensor heater (bank 1, 2, sensor 1) current is more than 10 A (1 trip detection logic) |
|
| 1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the C15 or C35 A/F sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| HA1A (1) - +B (2) | 20°C (68°F) | 1.8 to 3.4 Ω |
| HA1A (1) - A1A- (4) | - | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| HA2A (1) - +B (2) | 20°C (68°F) | 1.8 to 3.4 Ω |
| HA2A (1) - A2A- (4) | - | 10 kΩ or higher |
Reconnect the A/F sensor connector.
|
| ||||
| OK | |
| 2.CHECK TERMINAL VOLTAGE (+B OF A/F SENSOR) |
![]() |
Disconnect the C15 or C35 A/F sensor connector.
Turn the ignition switch to the ON position.
Measure the voltage between the terminals of the A/F sensor connector and body ground.
| Tester Connection | Specified Condition |
| +B (C15-2) - Body ground | 9 to 14 V |
| +B (C35-2) - Body ground | 9 to 14 V |
|
| ||||
| NG | |
| 3.INSPECT FUSE (A/F) |
Remove the A/F sensor fuse from the No. 1 integration relay.
Measure the A/F sensor fuse resistance.
Reinstall the A/F fuse.
|
| ||||
| OK | |
| 4.INSPECT ENGINE ROOM JUNCTION BLOCK (EFI RELAY, A/F RELAY) |
![]() |
Remove the engine room junction block from the engine room R/B.
Inspect the EFI relay.
Measure the EFI relay resistance.
| Tester Connection | Specified Condition |
| 1E-12 - 1E-6 | 10 kΩ or higher |
| 1E-12 - 1E-6 | Below 1 Ω (Apply battery voltage between terminals 1E-9 and 1E-10) |
Inspect the A/F relay.
Measure the A/F relay resistance.
| Tester Connection | Specified Condition |
| 1G-1 - 1A-4 | 10 kΩ or higher |
| 1G-1 - 1A-4 | Below 1 Ω (Apply battery voltage between terminals 1E-9 and 1E-10) |
|
| ||||
| OK | |
| 5.INSPECT FUSE (EFI MAIN) |
![]() |
Remove the EFI MAIN fuse from the engine room R/B.
Measure the EFI MAIN fuse resistance.
Reinstall the EFI MAIN fuse.
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (A/F SENSOR - A/F RELAY) |
![]() |
Disconnect the C15 or C35 A/F sensor connector.
Remove the engine room junction block from the engine room R/B.
Measure the resistance between the terminals.
| Tester Connection | Specified Condition |
| +B (C15-2) - 1A-4 (Engine room R/B) | Below 1 Ω |
| +B (C35-2) - 1A-4 (Engine room R/B) | Below 1 Ω |
| Tester Connection | Specified Condition |
| +B (C15-2) or 1A-4 (Engine room R/B) - Body ground | 10 kΩ or higher |
| +B (C35-2) or 1A-4 (Engine room R/B) - Body ground | 10 kΩ or higher |
Reinstall the engine room junction block.
Reconnect the A/F sensor connector.
|
| ||||
| OK | ||
| ||
| 7.CHECK HARNESS AND CONNECTOR |
![]() |
Disconnect the C15 or C35 A/F sensor connector.
Disconnect the C58 (RHD) or C55 (LHD) ECM connector.
Measure the resistance between the terminals.
| Tester Connection | Specified Condition |
| HA1A (C58-86) - HA1A (C15-1) | Below 1 Ω |
| HA2A (C58-109) - HA2A (C35-1) | Below 1 Ω |
| Tester Connection | Specified Condition |
| HA1A (C55-86) - HA1A (C15-1) | Below 1 Ω |
| HA2A (C55-109) - HA2A (C35-1) | Below 1 Ω |
| Tester Connection | Specified Condition |
| HA1A (C58-86) or HA1A (C15-1) - Body ground | 10 kΩ or higher |
| HA2A (C58-109) or HA2A (C35-1) - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| HA1A (C55-86) or HA1A (C15-1) - Body ground | 10 kΩ or higher |
| HA2A (C55-109) or HA2A (C35-1) - Body ground | 10 kΩ or higher |
Reconnect the ECM connector.
Reconnect the A/F sensor connectors.
|
| ||||
| OK | |
| 8.CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the intelligent tester ON.
Clear the DTCs (Click here).
Start the engine.
Allow the engine to idle for 1 minute or more.
Select the following menu items: Powertrain / Engine / DTC.
Read the DTCs.
| Display (DTC Output) | Proceed to |
| No output | A |
| P0031, P0032, P0051 and/or P0052 | B |
|
| ||||
| A | ||
| ||