DTC P0031 Oxygen (A/F) Sensor Heater Control Circuit Low (Bank 1 Sensor 1) |
DTC P0032 Oxygen (A/F) Sensor Heater Control Circuit High (Bank 1 Sensor 1) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0031 | Air-Fuel Ratio (A/F) sensor heater current less than 0.8 A (1 trip detection logic) |
|
| P0032 | Air-Fuel Ratio (A/F) sensor heater current more than 10 A (1 trip detection logic) |
|
| 1.INSPECT AIR-FUEL RATIO SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the C15 A/F sensor connector.
Measure the resistance between the terminals of the A/F sensor connector.
| Tester Connection | Specified Condition |
| HA1A (1) - +B (2) | 1.8 to 3.4 Ω at 20°C (68°F) |
| HA1A (1) - A1A- (4) | 10 kΩ or higher |
Reconnect the A/F sensor connector.
|
| ||||
| OK | |
| 2.CHECK TERMINAL VOLTAGE (+B OF A/F SENSOR) |
![]() |
Disconnect the C15 A/F sensor connector.
Turn the ignition switch to the ON position.
Measure the voltage between the terminal of the A/F sensor connector and body ground.
| Tester Connection | Specified Condition |
| +B (C15-2) - Body ground | 9 to 14 V |
Reconnect the A/F sensor connector.
|
| ||||
| NG | |
| 3.INSPECT ENGINE ROOM J/B (EFI RELAY, EFI MAIN FUSE) |
![]() |
Inspect the EFI MAIN fuse.
Remove the EFI MAIN fuse from the engine room J/B.
Measure the EFI MAIN fuse resistance.
Reinstall the EFI MAIN fuse.
Inspect the EFI relay.
Remove the engine room J/B from the engine room R/B.
Measure the EFI relay resistance.
| Tester Connection | Specified Condition |
| 1E-7 - 1E-12 | 10 kΩ or higher |
| Below 1 Ω (Apply battery voltage between terminals 1E-9 and 1E-11) |
Reinstall the engine room J/B.
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (A/F SENSOR - EFI RELAY) |
![]() |
Disconnect the C15 A/F sensor connector.
Remove the engine room J/B from the engine room R/B.
Disconnect the 1E engine room J/B connector.
Measure the resistance between the terminals.
| Tester Connection | Specified Condition |
| +B (C15-2) - Engine room J/B (1E-7) | Below 1 Ω |
| Tester Connection | Specified Condition |
| +B (C15-2) or Engine room J/B (1E-7) - Body ground | 10 kΩ or higher |
Reconnect the A/F sensor connector.
Reconnect the engine room J/B connector.
Reinstall the engine room J/B.
|
| ||||
| OK | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM) |
![]() |
Disconnect the C15 A/F sensor connector.
Disconnect the C24 ECM connector.
Measure the resistance between the terminals of the wire harness side connectors.
| Tester Connection | Specified Condition |
| HA1A (C15-1) - HA1A (C24-109) | Below 1 Ω |
| Tester Connection | Specified Condition |
| HA1A (C15-1) or HA1A (C24-109) - Body ground | 10 kΩ or higher |
Reconnect the A/F sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 6.CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the tester on.
Clear the DTCs (Click here).
Start the engine.
Allow the engine to idle for 1 minute or more.
Select the following menu items: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Display (DTC Output) | Proceed to |
| No output | A |
| P0031 or P0032 | B |
|
| ||||
| A | ||
| ||