DTC P2A00 A/F Sensor Circuit Slow Response (Bank 1 Sensor 1) |
DTC P2A03 A/F Sensor Circuit Slow Response (Bank 2 Sensor 1) |

| DTC No. | DTC Detection Conditions | Trouble Area |
| P2A00 P2A03 | Calculated value for air-fuel ratio (A/F) sensor response rate deterioration level is less than threshold |
|

| Tester Display (Sensor) | Injection Volume | Status | Voltage |
| AFS B1 S1 or AFS B2 S1 (A/F) | +25 % | Rich | Less than 3.0 V |
| AFS B1 S1 or AFS B2 S1 (A/F) | -12.5 % | Lean | More than 3.35 V |
| O2S B1 S2 or O2S B2 S2 (HO2) | +25 % | Rich | More than 0.55 V |
| O2S B1 S2 or O2S B2 S2 (HO2) | -12.5 % | Lean | Less than 0.4 V |
| Case | A/F Sensor (Sensor 1) Output Voltage | HO2 Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Area | ||
| 1 | Injection Volume +25 % -12.5 % | ![]() | Injection Volume +25 % -12.5 % | ![]() | - |
| Output Voltage More than 3.35 V Less than 3.0 V | ![]() | Output Voltage More than 0.55 V Less than 0.4 V | ![]() | ||
| 2 | Injection Volume +25 % -12.5 % | ![]() | Injection Volume +25 % -12.5 % | ![]() |
|
| Output Voltage Almost no reaction | ![]() | Output Voltage More than 0.55 V Less than 0.4 V | ![]() | ||
| 3 | Injection Volume +25 % -12.5 % | ![]() | Injection Volume +25 % -12.5 % | ![]() |
|
| Output Voltage More than 3.35 V Less than 3.0 V | ![]() | Output Voltage Almost no reaction | ![]() | ||
| 4 | Injection Volume +25 % -12.5 % | ![]() | Injection Volume +25 % -12.5 % | ![]() |
|
| Output Voltage Almost no reaction | ![]() | Output Voltage Almost no reaction | ![]() | ||
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P2A00 AND/OR P2A03) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the tester on.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
| Display (DTC Output) | Proceed to |
| P2A00 and/or P2A03 | A |
| P2A00 and/or P2A03 and other DTCs | B |
|
| ||||
| A | |
| 2.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the C15 or C35 A/F sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| HA1A (1) - +B (2) | 20°C (68°F) | 1.8 to 3.4 Ω |
| HA1A (1) - A1A- (4) | - | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| HA2A (1) - +B (2) | 20°C (68°F) | 1.8 to 3.4 Ω |
| HA2A (1) - A2A- (4) | - | 10 kΩ or higher |
Reconnect the A/F sensor connector.
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM) |
![]() |
Disconnect the C15 and C35 A/F sensor connectors.
Turn the ignition switch to the ON position.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| +B (C15-2) - Body ground | 9 to 14 V |
| +B (C35-2) - Body ground | 9 to 14 V |
Turn the ignition switch off.
Disconnect the C58 (RHD) or C55 (LHD) ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| HA1A (C15-1) - HA1A (C58-86) | Below 1 Ω |
| A1A+ (C15-3) - A1A+ (C58-93) | Below 1 Ω |
| A1A- (C15-4) - A1A- (C58-116) | Below 1 Ω |
| HA2A (C35-1) - HA2A (C58-109) | Below 1 Ω |
| A2A+ (C35-3) - A2A+ (C58-120) | Below 1 Ω |
| A2A- (C35-4) - A2A- (C58-119) | Below 1 Ω |
| Tester Connections | Specified Condition |
| HA1A (C15-1) - HA1A (C55-86) | Below 1 Ω |
| A1A+ (C15-3) - A1A+ (C55-93) | Below 1 Ω |
| A1A- (C15-4) - A1A- (C55-116) | Below 1 Ω |
| HA2A (C35-1) - HA2A (C55-109) | Below 1 Ω |
| A2A+ (C35-3) - A2A+ (C55-120) | Below 1 Ω |
| A2A- (C35-4) - A2A- (C55-119) | Below 1 Ω |
| Tester Connection | Specified Condition |
| HA1A (C15-1) or HA1A (C58-86) - Body ground | 10 kΩ or higher |
| A1A+ (C15-3) or A1A+ (C58-93) - Body ground | 10 kΩ or higher |
| A1A- (C15-4) or A1A- (C58-116) - Body ground | 10 kΩ or higher |
| HA2A (C35-1) or HA2A (C58-109) - Body ground | 10 kΩ or higher |
| A2A+ (C35-3) or A2A+ (C58-120) - Body ground | 10 kΩ or higher |
| A2A- (C35-4) or A2A- (C58-119)- Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| HA1A (C15-1) or HA1A (C55-86) - Body ground | 10 kΩ or higher |
| A1A+ (C15-3) or A1A+ (C55-93) - Body ground | 10 kΩ or higher |
| A1A- (C15-4) or A1A- (C55-116) - Body ground | 10 kΩ or higher |
| HA2A (C35-1) or HA2A (C55-109) - Body ground | 10 kΩ or higher |
| A2A+ (C35-3) or A2A+ (C55-120) - Body ground | 10 kΩ or higher |
| A2A- (C35-4) or A2A- (C55-119) - Body ground | 10 kΩ or higher |
Reconnect the ECM connector.
Reconnect the A/F sensor connector.
|
| ||||
| OK | |
| 4.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00 AND/OR P2A03) |
Read the DTCs using the intelligent tester.
Enter the following menus: Powertrain / Engine / DTC.
| Display (DTC Output) | Proceed to |
| P2A00 and/or P2A03 | A |
| No output | B |
|
| ||||
| A | |
| 6.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ratio sensor (Click here).
| NEXT | |
| 7.PERFORM CONFIRMATION DRIVING PATTERN |
| NEXT | |
| 8.CHECK WHETHER DTC OUTPUT RECURS (DTC P2A00 AND/OR P2A03) |
Read the DTCs using the intelligent tester.
Enter the following menus: Powertrain / Engine / DTC.
| Display (DTC Output) | Proceed to |
| No output | A |
| P2A00 and/or P2A03 | B |
|
| ||||
| A | ||
| ||