Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM (for LHD)

CAN COMMUNICATION SYSTEM (for LHD) > Short to B+ in CAN Bus Line

for Preparation Click here


DESCRIPTION

A short to B+ is suspected in the CAN bus wire when the resistance between terminals 6 (CANH) and 16 (BAT), or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ.

Symptom
Trouble Area
The resistance between terminals 6 (CANH) and 16 (BAT), or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ.
  1. Short to B+ in CAN bus wire
  2. Skid control ECU
  3. Steering angle sensor
  4. Yaw rate sensor
  5. ECM
  6. Main body ECU
  7. A/C amplifier
  8. Center airbag sensor assembly
  9. Combination meter

WIRING DIAGRAM


C142702E01


C142703E01


INSPECTION PROCEDURE

NOTICE:
  1. Turn the ignition switch off before measuring the resistance of the CAN main wire and CAN branch wires.
  2. After the ignition switch is turned off, check that the key reminder warning system and lighting system are not operating.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
Operating the ignition switch, any other switches or any triggers related ECU and sensor communication on the CAN, which would cause resistance reading variations.

1.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (DLC3 BRANCH WIRE)


    C133233E01
  1. Turn the ignition switch off.

  1. Disconnect the DLC3 branch wire connector (E62) from the No. 1 CAN J/C "B" side (without earth terminal).

    NOTICE:
    1. Before disconnecting the connector, make a note of where it is connected.
    2. Reconnect the connector to its original position.



    C126231E12
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E10-6 (CANH) - E10-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E10-14 (CANL) - E10-16 (BAT)
    Ignition switch off
    6 kΩ or higher

  1. Reconnect the DLC3 branch wire connector (E62) to the No. 1 CAN J/C "B" side (without earth terminal).



NG
REPAIR OR REPLACE DLC3 BRANCH WIRE OR CONNECTOR
OK


2.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 CAN J/C SIDE)


    C133228E01
  1. Disconnect the CAN main bus wire connector (E42) from the No. 1 CAN J/C "A" side (with earth terminal).



    C126231E12
  1. Measure the resistance between terminals 6 (CANH) and 16 (BAT), and between terminals 14 (CANL) and 16 (BAT) of the DLC3 each time a connector is disconnected.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E10-6 (CANH) - E10-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E10-14 (CANL) - E10-16 (BAT)
    Ignition switch off
    6 kΩ or higher



OK
Go to step 6
NG


3.CHECK FOR SHORT TO B+ IN CAN BUS WIRE


    C126231E12
  1. Disconnect connectors from the No. 1 CAN J/C one at a time.

    HINT:
    Disconnect the ECU and sensor connectors other than the DLC3 branch wires and CAN main bus wires between the No. 1 CAN J/C.



  1. Measure the resistance between terminals 6 (CANH) and 16 (BAT), and between terminals 14 (CANL) and 16 (BAT) of the DLC3 each time a connector is disconnected.


    C133265E02


    C137761E02


    No. 1 CAN J/C connectors ("A" side, with earth terminal)
    Connector Color
    Wire Color (CAN-H)
    Wire Color (CAN-L)
    Airbag Sensor Assembly Center (E45)
    Black
    B
    W

    No. 1 CAN J/C connectors ("A" side, with earth terminal)
    Connector Color
    Wire Color (CAN-H)
    Wire Color (CAN-L)
    Yaw Rate Sensor (E46)*
    Blue
    B
    W
    Steering Angle Sensor (E63)*
    Brown
    B
    W
    Combination Meter (E43)
    White
    B
    W
    Main Body ECU (E44)
    Black
    B
    W
    *: with VSC

    NOTICE:
    Do not reconnect the disconnected connectors until this inspection is complete because there may be a short to B+ in 2 or more CAN bus wires.


    Result:

    Symptom
    Proceed to
    The resistance between terminals 6 (CANH) and 16 (BAT), or the resistance between 14 (CANL) and 16 (BAT) is still below 6 kΩ when all the specified connectors are disconnected from the No. 1 CAN J/C. (There is a short to B+ in the CAN main bus wires between the No. 1 CAN J/C and No. 2 CAN J/C.)
    OK
    The resistance between terminals 6 (CANH) and 16 (BAT), or the resistance between 14 (CANL) and 16 (BAT) becomes normal (6 kΩ or more) when a connector is disconnected from the No. 1 CAN J/C. (There is a short to B+ in one of the areas that relate to one or more of the disconnected bus wires.)
    NG

  1. When there is a short to B+ in one or more of the bus wires that connect to an ECU (or sensor):

    1. Reconnect all of the connectors to the No. 1 CAN J/C, except for the one that was disconnected last (the bus wire that is shorted to B+). Check that the resistance shown on the tester is normal (6 kΩ or more) to confirm that there is a short to B+ in one bus wire only.

      HINT:
      1. The connectors connected to the No. 1 CAN J/C can be distinguished according to the color of the communication bus wires and the shape of the connectors.
      2. Reconnecting the connectors to non-specified positions on the No. 1 CAN J/C does not affect system operation. However, it is preferred to reconnect the connectors to their specified positions to avoid negative effects on the wiring such as tension on the wiring harnesses, and to make future maintenance easier.


NEXT


4.RECONNECT CONNECTOR
  1. Reconnect the connector of the bus wire that is shorted to B+ to the No. 1 CAN J/C (the connector that caused the bus wire resistance to change to 6 kΩ or more when it was disconnected).


NEXT


5.CHECK FOR SHORT TO B+ IN CAN BUS WIRE


    C126231E12
  1. Disconnect the connector that includes terminals CANH and CANL from the ECU (or sensor) to which the bus wire shorted to B+ is connected. (Click here)

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E10-6 (CANH) - E10-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E10-14 (CANL) - E10-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    HINT:
    If the resistance changes to 6 kΩ or higher when the connector is disconnected from the ECU (or sensor), there may be a short in the ECU (or sensor).



NG
REPAIR OR REPLACE CORRESPONDING ECU OR SENSOR BUS LINE OR CONNECTOR
OK

REPLACE CORRESPONDING ECU OR SENSOR 

6.CHECK FOR SHORT TO B+ IN CAN BUS WIRE


    C133245E47
  1. Reconnect the CAN main bus wire connector (E42) to the No. 1 CAN J/C A side (with earth terminal).

  1. Disconnect the No. 2 CAN J/C connector (A40).



    C126231E12
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E10-6 (CANH) - E10-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E10-14 (CANL) - E10-16 (BAT)
    Ignition switch off
    6 kΩ or higher



OK
Go to step 10
NG


7.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 CAN J/C - NO. 2 CAN J/C)


    C133246E45
  1. Disconnect the No. 2 CAN J/C connector (E41).



    C126231E12
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E10-6 (CANH) - E10-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E10-14 (CANL) - E10-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    HINT:
    Measure the resistance with the No. 2 CAN J/C connector (A40) disconnected.



NG
REPAIR OR REPLACE CAN BUS MAIN WIRE (NO. 1 CAN J/C - NO. 2 CAN J/C)
OK


8.RECONNECT CONNECTOR
  1. Reconnect the No. 2 CAN J/C connector (A40).


NEXT


9.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (A/C AMPLIFIER)


    C133246E46
  1. Disconnect the A/C amplifier connector (E38).



    C126231E14
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    E41-1 (CANH) - E10-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E41-7 (CANL) - E10-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    HINT:
    Measure the resistance with the No. 2 CAN J/C connector (E41) disconnected.



NG
REPAIR OR REPLACE A/C AMPLIFIER BRANCH LINE OR CONNECTOR
OK

REPLACE A/C AMPLIFIER 

10.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECM MAIN BUS WIRE)


    C133245E44
  1. Disconnect the No. 2 CAN J/C connector (A40).



    C126231E14
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    A40-1 (CANH) - E10-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    A40-7 (CANL) - E10-16 (BAT)
    Ignition switch off
    6 kΩ or higher



OK
Go to step 12
NG


11.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECM)


    C133245E44
  1. Disconnect the ECM connector (A24 or A55).



    C126231E14
  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    A40-1 (CANH) - E10-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    A40-7 (CANL) - E10-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    HINT:
    Measure the resistance with the No. 2 CAN J/C connector (A40) disconnected.



NG
REPAIR OR REPLACE CAN BUS MAIN WIRE OR CONNECTOR (ECM - NO. 2 CAN J/C)
OK

REPLACE ECM 

12.CHECK FOR SHORT TO B+ IN CAN BUS WIRE (SKID CONTROL ECU)


    C133245E45
    C126231E14
  1. Disconnect the skid control ECU connector (A25 or A26).

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Value
    A40-2 (CANH) - E10-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    A40-8 (CANL) - E10-16 (BAT)
    Ignition switch off
    6 kΩ or higher



OK
REPLACE BRAKE ACTUATOR ASSEMBLY
NG

REPAIR OR REPLACE SKID CONTROL ECU BRANCH WIRE OR CONNECTOR