CAN COMMUNICATION SYSTEM (for LHD) > Short to GND in CAN Bus Line |
| Symptoms | Trouble Area |
| The resistance between terminals 6 (CANH) and 4 (CG), or terminals 14 (CANL) and 4 (CG) of the DLC3 is below 200 Ω. |
|


| 1.CHECK FOR SHORT TO GND IN CAN BUS WIRE (DLC3 BRANCH WIRE) |
![]() |
Turn the ignition switch off.
Disconnect the DLC3 branch wire connector (E62) from the No. 1 CAN J/C B side (without earth terminal).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| E10-6 (CANH) - E10-4 (CG) | Ignition switch off | 200 Ω or higher |
| E10-14 (CANL) - E10-4 (CG) | Ignition switch off | 200 Ω or higher |
Reconnect the DLC3 branch wire connector (E62) to the No. 1 CAN J/C B side (without earth terminal).
|
| ||||
| OK | |
| 2.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN J/C SIDE) |
![]() |
Disconnect the CAN main bus wire connector (E42) from the No. 1 CAN J/C A side (with earth terminal).
![]() |
Using an ohmmeter, measure the resistance between terminals 6 (CANH) and 4 (CG), and between terminals 14 (CANL) and 4 (CG) of the DLC3 each time a connector is disconnected.
| Tester Connection | Condition | Specified Value |
| E10-6 (CANH) - E10-4 (CG) | Ignition switch off | 200 Ω or higher |
| E10-14 (CANL) - E10-4 (CG) | Ignition switch off | 200 Ω or higher |
|
| ||||
| NG | |
| 3.CHECK FOR SHORT TO GND IN CAN BUS WIRE |
![]() |
Disconnect connectors from the No. 1 CAN J/C one at a time.
Using an ohmmeter, measure the resistance between terminals 6 (CANH) and 4 (CG), and between terminals 14 (CANL) and 4 (CG) of the DLC3 each time a connector is disconnected.


| No. 1 CAN J/C connectors ("A" side, with earth terminal) | Connector Color | Wire Color (CAN-H) | Wire Color (CAN-L) |
| Airbag Sensor Assembly Center (E45) | Black | B | W |
| No. 1 CAN J/C connectors ("A" side, with earth terminal) | Connector Color | Wire Color (CAN-H) | Wire Color (CAN-L) |
| Yaw Rate Sensor (E46)* | Blue | B | W |
| Steering Angle Sensor (E63)* | Brown | B | W |
| Combination Meter (E43) | White | B | W |
| Main Body ECU (E44) | Black | B | W |
| Symptom | Proceed to |
| The resistance between terminals 6 (CANH) and 4 (CG), or the resistance between 14 (CANL) and 4 (CG) is still below 200 Ω when all the specified connectors are disconnected from the No. 1 CAN J/C. (There is a short to GND in the CAN main bus wires between the No. 1 CAN J/C and No. 2 CAN J/C.) | A |
| The resistance between terminals 6 (CANH) and 4 (CG), or the resistance between 14 (CANL) and 4 (CG) becomes normal (200 Ω or more) when a connector is disconnected from the CAN J/C. (There is a short to GND in one of the areas that relate to the disconnected bus wires.) | B |
When there is a short to GND in one or more of the bus wires that connect to an ECU (or sensor):
Reconnect all of the connectors to the No. 1 CAN J/C, except for the one that was disconnected last (the bus wire that is shorted to GND). Check that the resistance shown on the tester is normal (200 Ω or more) to confirm that there is a short to GND in one branch wire only.
|
| ||||
| B | |
| 4.RECONNECT CONNECTOR |
Reconnect the connector of the bus wire that is shorted to GND to the No. 1 CAN J/C (the connector that caused the bus wire resistance to change to 200 Ω or more when it was disconnected).
| NEXT | |
| 5.CHECK FOR SHORT TO GND IN CAN BUS WIRE |
![]() |
Disconnect the connector that includes terminals CANH and CANL from the ECU (or sensor) to which the bus wire shorted to GND is connected (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| E10-6 (CANH) - E10-4 (CG) | Ignition switch off | 200 Ω or higher |
| E10-14 (CANL) - E10-4 (CG) | Ignition switch off | 200 Ω or higher |
|
| ||||
| OK | ||
| ||
| 6.CHECK FOR SHORT TO GND IN CAN BUS WIRE |
![]() |
Reconnect the CAN main bus wire connector (E42) to the No. 1 CAN J/C A side (with earth terminal).
Disconnect the No. 2 CAN J/C connector (A40).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| E10-6 (CANH) - E10-4 (CG) | Ignition switch off | 200 Ω or higher |
| E10-14 (CANL) - E10-4 (CG) | Ignition switch off | 200 Ω or higher |
|
| ||||
| NG | |
| 7.CHECK FOR SHORT TO GND IN CAN BUS WIRE (NO. 1 CAN J/C - NO. 2 CAN J/C) |
![]() |
Disconnect the No. 2 CAN J/C connector (E41).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| E41-4 (CANH) - E10-4 (CG) | Ignition switch off | 200 Ω or higher |
| E41-10 (CANL) - E10-4 (CG) | Ignition switch off | 200 Ω or higher |
|
| ||||
| OK | |
| 8.RECONNECT CONNECTOR |
Reconnect the No. 2 CAN J/C connector (A40).
| NEXT | |
| 9.CHECK FOR SHORT TO GND IN CAN BUS WIRE (A/C AMPLIFIER) |
![]() |
Disconnect the A/C amplifier connector (E38).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| E41-1 (CANH) - E10-4 (CG) | Ignition switch off | 200 Ω or higher |
| E41-7 (CANL) - E10-4 (CG) | Ignition switch off | 200 Ω or higher |
|
| ||||
| OK | ||
| ||
| 10.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECM MAIN BUS WIRE) |
![]() |
Disconnect the No. 2 CAN J/C connector (A40).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| A40-1 (CANH) - E10-4 (CG) | Ignition switch off | 200 Ω or higher |
| A40-7 (CANL) - E10-4 (CG) | Ignition switch off | 200 Ω or higher |
|
| ||||
| NG | |
| 11.CHECK FOR SHORT TO GND IN CAN BUS WIRE (ECM) |
![]() |
Disconnect the ECM connector (A24 or A55).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| A40-1 (CANH) - E10-4 (CG) | Ignition switch off | 200 Ω or higher |
| A40-7 (CANL) - E10-4 (CG) | Ignition switch off | 200 Ω or higher |
|
| ||||
| OK | ||
| ||
| 12.CHECK FOR SHORT TO GND IN CAN BUS WIRE (SKID CONTROL ECU) |
![]() |
Disconnect the skid control ECU connector (A25 or A26).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Value |
| A40-2 (CANH) - E10-4 (CG) | Ignition switch off | 200 Ω or higher |
| A40-8 (CANL) - E10-4 (CG) | Ignition switch off | 200 Ω or higher |
|
| ||||
| NG | ||
| ||