SFI SYSTEM > ECM Power Source Circuit |

| 1.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND) |
![]() |
Disconnect the C58 (RHD) or C55 (LHD) ECM connector.
Measure the resistance between the terminals.
| Tester Connection | Specified Condition |
| E1 (C58-81) - Body ground | Below 1 Ω |
| Tester Connection | Specified Condition |
| E1 (C55-81) - Body ground | Below 1 Ω |
Reconnect the ECM connector.
|
| ||||
| OK | |
| 2.CHECK ENGINE ROOM JUNCTION BLOCK (EFI RELAY VOLTAGE) |
![]() |
Remove the engine room junction block from the engine room R/B.
Turn the ignition switch to the ON position.
Measure the voltage between the terminals.
| Tester Connection | Specified Condition |
| 1E-6 - Body ground | 9 to 14 V |
|
| ||||
| NG | |
| 3.INSPECT EFI MAIN FUSE |
![]() |
Remove the EFI MAIN fuse from the engine room R/B.
Measure the EFI MAIN fuse resistance.
Reinstall the EFI MAIN fuse.
|
| ||||
| OK | |
| Go to step 6 |
| 4.CHECK HARNESS AND CONNECTOR (ENGINE ROOM JUNCTION BLOCK - BATTERY) |
![]() |
Disconnect the negative battery terminal.
Disconnect the positive battery terminal.
Remove the engine room junction block from the engine room R/B.
Measure the resistance between the terminals.
| Tester Connection | Specified Condition |
| 1G-1 - Positive battery terminal | Below 1 Ω |
| Tester Connection | Specified Condition |
| 1G-1 or Positive battery terminal - Body ground | 10 kΩ or higher |
Reinstall the engine room junction block.
Reconnect the positive battery terminal.
Reconnect the negative battery terminal.
|
| ||||
| OK | ||
| ||
| 5.INSPECT ENGINE ROOM JUNCTION BLOCK (EFI RELAY) |
![]() |
Remove the engine room junction block from the engine room R/B.
Measure the resistance between the terminals.
| Tester Connection | Specified Condition |
| 1E-6 - 1E-12 | 10 kΩ or higher |
| 1E-6 - 1E-12 | Below 1 Ω (Apply battery voltage between terminals 1E-9 and 1E-11) |
Reinstall the engine room junction block.
|
| ||||
| OK | |
| 6.INSPECT EFI NO. 2 FUSE |
![]() |
Remove the EFI No. 2 fuse from the engine room R/B.
Measure the EFI No. 2 fuse resistance.
Reinstall the EFI No. 2 fuse.
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (ECM - ENGINE ROOM JUNCTION BLOCK) |
![]() |
Disconnect the A24 (RHD) or A55 (LHD) ECM connector.
Remove the engine room junction block from the engine room R/B.
Measure the resistance between the terminals.
| Tester Connection | Specified Condition |
| 1E-6 - +B (A24-2) | Below 1 Ω |
| 1E-6 - +B2 (A24-1) | Below 1 Ω |
| Tester Connection | Specified Condition |
| 1E-6 - +B (A55-2) | Below 1 Ω |
| 1E-6 - +B2 (A55-1) | Below 1 Ω |
| Tester Connection | Specified Condition |
| 1E-6 or +B (A24-2) - Body ground | 10 kΩ or higher |
| 1E-6 or +B2 (A24-1) - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| 1E-6 or +B (A55-2) - Body ground | 10 kΩ or higher |
| 1E-6 or +B2 (A55-1) - Body ground | 10 kΩ or higher |
Reinstall the engine room junction block.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 8.INSPECT ECM (IGSW VOLTAGE) |
![]() |
Disconnect the A24 (RHD) or A55 (LHD) ECM connector.
Measure the voltage between the terminals.
| Tester Connection | Specified Condition |
| IGSW (A24-28) - Body ground | 9 to 14 V |
| Tester Connection | Specified Condition |
| IGSW (A55-28) - Body ground | 9 to 14 V |
Reconnect the ECM connector.
|
| ||||
| NG | |
| 9.INSPECT IGNITION RELAY NO. 2 |
![]() |
Remove the IG2 relay from the engine room R/B.
Measure the resistance between the terminals.
| Tester Connection | Specified Condition |
| 3 - 5 | 10 kΩ or higher |
| 3 - 5 | Below 1 Ω (Apply battery voltage between terminals 1 and 2) |
Reinstall the IG2 relay.
|
| ||||
| OK | |
| 10.CHECK HARNESS AND CONNECTOR (IG2 RELAY - BODY GROUND) |
![]() |
Remove the IG2 relay from the engine room R/B.
Measure the resistance between the terminals.
| Tester Connection | Specified Condition |
| IG2 relay terminal 2 - Body ground | Below 1 Ω |
Reinstall the IG2 relay.
| Result | Proceed to |
| OK | A |
| NG | B |
|
| ||||
| A | |
| 11.INSPECT IGNITION SWITCH ASSEMBLY |
![]() |
Disconnect the E23 ignition switch connector.
Measure the resistance between the terminals.
| Tester Connection | Ignition Switch Position | Specified Condition |
| All terminals | LOCK | 10 kΩ or higher |
| 2 - 4 | ACC | Below 1 Ω |
| 1 - 2 - 4, 5 - 6 | ON | |
| 1 - 3 - 4, 5 - 6 - 7 | START |
Reconnect the ignition switch connector.
|
| ||||
| OK | ||
| ||
| 12.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND) |
![]() |
Disconnect the A24 (RHD) or A55 (LHD) ECM connector.
Measure the resistance between the terminals.
| Tester Connection | Specified Condition |
| MREL (A24-24) - Body ground | Below 1 Ω |
| Tester Connection | Specified Condition |
| MREL (A55-24) - Body ground | Below 1 Ω |
Reconnect the ECM connector.
|
| ||||
| OK | ||
| ||