AIR CONDITIONING SYSTEM > Air Conditioning Compressor Magnetic Clutch Circuit |

| 1.CHECK CAN COMMUNICATION SYSTEM |
Use the intelligent tester to check if the CAN Communication System is functioning normally.
| Result | Proceed to |
| CAN DTC is not output | A |
| CAN DTC is output | B |
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the intelligent tester main switch on.
Turn the A/C switch on and off.
Select the item below in the Data List, and read the display on the intelligent tester.
| Item | Measure Item | Normal Condition | Diagnostic Note |
| A/C Signal (A/C Signal) | A/C signal / ON or OFF | ON: A/C ON OFF: A/C OFF | - |
|
| ||||
| OK | |
| 3.INSPECT FUSE (A/C NO. 2) |
![]() |
Remove the A/C No. 2 fuse from the instrument panel J/B.
Measure the resistance of the fuse.
| Tester Item | Condition | Specified Condition |
| A/C No. 2 fuse | Always | Below 1 Ω |
Reconnect the A/C No. 2 fuse to the instrument panel J/B.
|
| ||||
| OK | |
| 4.INSPECT RELAY (MGC) |
![]() |
Remove the MGC relay from the engine room R/B and J/B.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| 3 - 5 | 10 kΩ or higher |
| 3 - 5 | Below 1 Ω (when battery voltage is applied to terminals 1 and 2) |
Install the MGC relay to the engine room R/B and J/B.
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (A/C AMPLIFIER - BATTERY) |
![]() |
Disconnect the connector from the A/C amplifier.
Measure the voltage according to the value(s) in the table below.
| Tester Connection (Symbols) | Condition | Specified Condition |
| E38-20 (MGC) - Body ground | Ignition switch: LOCK | Below 1 V |
| E38-20 (MGC) - Body ground | Ignition switch: ON | 10 to 14 V |
|
| ||||
| OK | |
| 6.INSPECT AIR CONDITIONING AMPLIFIER |
![]() |
Reconnect the connector to the A/C amplifier.
Measure the voltage according to the value(s) in the table below.
| Tester Connection (Symbols) | Condition | Specified Condition |
| E38-20 (MGC) - Body ground | Ignition switch: ON A/C switch: OFF | 10 to 14 V |
| E38-20 (MGC) - Body ground | Ignition switch: ON A/C switch: ON | Below 1 V |
|
| ||||
| OK | |
| 7.INSPECT A/C COMPRESSOR |
![]() |
Disconnect the connector from the A/C compressor.
![]() |
Disconnect the connector from the magnetic clutch.
Measure the resistance according to the value(s) in the table below.
| Tester Connection (Symbols) | Condition | Specified Condition |
| C53-3 (MG+) - A-1 | Always | Below 1 Ω |
| C53-3 (MG+) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 8.INSPECT MAGNETIC CLUTCH |
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A-1 - Body ground | Always | 3.4 to 3.8 Ω |
When connector terminal A1 is connected to the positive (+) battery terminal, check that the following occurs: 1) the magnetic clutch's operating sound can be heard, and 2) the magnetic clutch's hub and rotor lock.
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (ENGINE ROOM R/B AND J/B - BATTERY) |
![]() |
Remove the MGC relay from the engine room R/B and J/B.
Turn the ignition switch to the ON position.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| Relay block MGC relay terminal 5 - Body ground | 10 to 14 V |
| Relay block MGC relay terminal 1 - Body ground | 10 to 14 V |
|
| ||||
| OK | ||
| ||