AIRBAG SYSTEM > SYSTEM DESCRIPTION |
| GENERAL |
In conjunction with impact absorbing structure for a front collision, the SRS (Supplemental Restraint System) driver airbag and front passenger airbag were designed to supplement seat belts in the event of a front collision in order to help reduce shock to the head and chest of the driver and front passenger. This system is a 3-sensor type airbag system to detect the impact during a front collision using the center airbag sensor assembly and front airbag sensors. It also operates the airbag system and seat belt pretensioner.
In order to detect the extent of the collision during the initial stages of the collision in further details, the front airbag sensors have been changed from mechanical type to electrical type deceleration sensors. Accordingly, the deployment of the driver airbag and front passenger airbag is controlled in two stages according to the severity of the impact.
In conjunction with impact absorbing structure for a side collision, the side airbag and curtain shield airbag were designed to help reduce shock to the driver, front passenger, and rear outer passengers in the event of a side collision.
The curtain shield airbag that helps reduce shock to the front and rear seat occupants with a single curtain shield airbag has been adopted. In conjunction with this system, the side airbag sensors have been installed at the bottom of the center pillars and the rear airbag sensors have been installed at the bottom of the rear pillars.
In this system, a front side collision is detected by the side airbag sensor in order to simultaneously deploy the side and curtain shield airbags. A rear side collision is detected by the rear airbag sensor and the center airbag sensor assembly in order to deploy the curtain shield airbag.
The center airbag sensor assembly sends the airbag deployment signal to the ECM through CAN (Controller Area Network) to operate the fuel pump control.
| CONSTRUCTION AND OPERATION |
FRONT AIRBAG SENSOR
The front airbag sensors are installed on the right and left radiator supports respectively.
The front airbag sensor use an electrical type deceleration sensor.
The deceleration sensor is built into the front airbag sensor, and the distortion that is created in the sensor is converted into an electric signal based on the vehicle deceleration rate during a frontal collision. Accordingly, the extent of the initial collision can be detected in detail.
SIDE AIRBAG SENSOR
The side airbag sensors are installed on the bottom of the right and left center pillars respectively.
The side airbag sensor consists of the deceleration sensor and ignition control circuit.
The deceleration sensor is built into the side airbag sensor, and the distortion that is created in the sensor is converted into an electric signal based on the vehicle deceleration rate during a front side collision. Accordingly, the extent of the initial collision can be detected in detail.
REAR AIRBAG SENSOR
The rear airbag sensors are installed on the right and left rear pillars respectively.
The rear airbag sensor consists of the deceleration sensor and ignition control circuit.
The deceleration sensor is built into the rear airbag sensor, and the distortion that is created in the sensor is converted into an electric signal based on the vehicle deceleration rate during a rear side collision. Accordingly, the extent of the initial collision can be detected in detail.
CENTER AIRBAG SENSOR ASSEMBLY
General
Deceleration sensor and ignition control circuit
Safing sensor
Electronic safing sensor
Backup power source
Diagnostic circuit
Memory circuit
SRS WARNING LIGHT
The SRS warning light is located on the combination meter assembly. It comes on to inform the driver of system trouble when a malfunction is detected in self-diagnosis of the center airbag sensor assembly. Under normal operating conditions, when the ignition switch is turned to the ON position, it comes on for approximately 6 seconds and then goes off.
| DEPLOYMENT CONDITION |
The center airbag sensor assembly determines whether ignition is necessary based on signals from the deceleration sensor and the front airbag sensor (*1). If the safing sensor turns on simultaneously, current flows to the squibs to deploy the SRS as shown in the illustration below.

The center airbag sensor assembly determines whether ignition is necessary based on signals from the side airbag sensor. If the safing sensor turns on simultaneously, current flows to the squib to deploy the SRS as shown in the illustration below.

The center airbag sensor assembly determines whether ignition is necessary based on signals from the rear airbag sensor. If the safing sensor turns on simultaneously, current flows to the squib to deploy the SRS as shown in the illustration below (*1).
