DTC P0300 Random / Multiple Cylinder Misfire Detected |
DTC P0301 Cylinder 1 Misfire Detected |
DTC P0302 Cylinder 2 Misfire Detected |
DTC P0303 Cylinder 3 Misfire Detected |
DTC P0304 Cylinder 4 Misfire Detected |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0300 | Simultaneous misfiring of several cylinders occurs and one of following conditions below is detected (2 trip detection logic):
|
|
| P0301 P0302 P0303 P0304 | Misfiring of a specific cylinder occurs and one of following conditions below is detected (2 trip detection logic):
|
| Engine Speed | Duration |
| Idling | 8 minutes or more |
| 1000 | 4.5 minutes or more |
| 2000 | 2.5 minutes or more |
| 3000 | 1.5 minutes or more |
| 1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE DTCS) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / DTC.
Read the DTCs.
| Result | Proceed to |
| DTC P0300, P0301, P0302, P0303 and/or P0304 are output | A |
| DTC P0300, P0301, P0302, P0303 and/or P0304 and other DTCs are output | B |
|
| ||||
| A | |
| 2.CHECK PCV HOSE CONNECTIONS |
Check the PCV hose connections.
|
| ||||
| OK | |
| 3.READ VALUE USING INTELLIGENT TESTER (MISFIRE RPM AND MISFIRE LOAD) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Misfire RPM and Misfire Load.
Read and note the Misfire RPM and Misfire Load values.
| NEXT | |
| 4.READ VALUE USING INTELLIGENT TESTER (CYLINDER #1, #2, #3 AND #4 MISFIRE COUNT) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Cylinder #1 (to #4) Misfire Count.
Read each value for Cylinder #1 (to #4) Misfire Count displayed on the tester. If no misfire counts occur in any cylinders, perform steps [A] and [B] and then check the misfire counts again.
Drive the vehicle with the Misfire RPM and Misfire Load noted in the "READ VALUE USING INTELLIGENT TESTER (MISFIRE RPM AND MISFIRE LOAD)" procedures above [A].
Read the Cylinder #1 (to #4) Misfire Count or DTCs displayed on the tester [B].
| Result (Misfire Count) | Proceed to |
| Most misfires occur in only 1 or 2 cylinders | A |
| 3 cylinders or more have equal misfire counts | B |
|
| ||||
| A | |
| 5.INSPECT SPARK PLUG |
Inspect the spark plug of the misfiring cylinder .
|
| ||||
| OK | |
| 6.CHECK FOR SPARK (SPARK TEST) |
Perform a spark test .
|
| ||||
| OK | |
| 7.CHECK CYLINDER COMPRESSION PRESSURE OF MISFIRING CYLINDER |
Measure the cylinder compression pressure of the misfiring cylinder .
|
| ||||
| OK | |
| 8.CHECK FUEL INJECTOR ASSEMBLY (POWER SOURCE) |
![]() |
Disconnect the fuel injector assembly connectors.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C7-1 - Body ground | Ignition switch ON | 11 to 14 V |
| C8-1 - Body ground | Ignition switch ON | 11 to 14 V |
| C9-1 - Body ground | Ignition switch ON | 11 to 14 V |
| C10-1 - Body ground | Ignition switch ON | 11 to 14 V |
| *1 | Front view of wire harness connector (to Fuel Injector Assembly) |
Turn the ignition switch off.
Reconnect the fuel injector assembly connectors.
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM) |
Disconnect the fuel injector assembly connectors.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C7-2 - C24-108 (#10) | Always | Below 1 Ω |
| C9-2 - C24-107 (#20) | Always | Below 1 Ω |
| C8-2 - C24-106 (#30) | Always | Below 1 Ω |
| C10-2 - C24-105 (#40) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| C7-2 or C24-108 (#10) - Body ground | Always | 10 kΩ or higher |
| C9-2 or C24-107 (#20) - Body ground | Always | 10 kΩ or higher |
| C8-2 or C24-106 (#30) - Body ground | Always | 10 kΩ or higher |
| C10-2 or C24-105 (#40) - Body ground | Always | 10 kΩ or higher |
Reconnect the fuel injector assembly connectors.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 10.INSPECT FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER |
Inspect the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).
|
| ||||
| OK | |
| 11.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leaks.
|
| ||||
| OK | |
| 12.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 13.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Coolant Temp.
Read the Coolant Temp twice, when the engine is both cold and warmed up.
|
| ||||
| OK | |
| 14.READ VALUE USING INTELLIGENT TESTER (MAF) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF and Coolant Temp.
Allow the engine to idle until Coolant Temp reaches 75 °C (167°F) or higher.
Read the MAF with the engine in an idling condition and at an engine speed of 2500 rpm.
|
| ||||
| OK | |
| 15.CHECK VALVE TIMING |
![]() |
Remove the cylinder head cover.
Turn the crankshaft pulley, then align its groove with the timing mark "0" on the timing chain cover.
Check that the point marks on the camshaft timing gears are aligned with the timing chain cover surface as shown in the illustration.
If not, turn the crankshaft 1 revolution (360°), then align the marks as above.
| *1 | Alignment Marks |
| *2 | Groove |
Reinstall the cylinder head cover.
|
| ||||
| OK | |
| 16.CHECK VALVE CLEARANCE OF MISFIRING CYLINDER |
Check the valve clearance (Click here).
|
| ||||
|
| ||||
| 17.CHECK INTAKE SYSTEM |
Check the intake system for vacuum leaks.
|
| ||||
| OK | |
| 18.CHECK FUEL PRESSURE |
Check the fuel pressure .
|
| ||||
| OK | |
| 19.READ VALUE USING INTELLIGENT TESTER (COOLANT TEMP) |
Check the fuel pressure .
|
| ||||
| OK | |
| 20.READ VALUE USING INTELLIGENT TESTER (MAF) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF and Coolant Temp.
Allow the engine to idle until Coolant Temp reaches 75 °C (167°F) or higher.
Read the MAF with the engine in an idling condition and at an engine speed of 2500 rpm.
|
| ||||
| OK | |
| 21.CHECK VALVE TIMING |
![]() |
Remove the cylinder head cover.
Turn the crankshaft pulley, then align its groove with the timing mark "0" on the timing chain cover.
Check that the point marks on the camshaft timing gears are aligned with the timing chain cover surface as shown in the illustration.
If not, turn the crankshaft 1 revolution (360°), then align the marks as above.
| *1 | Alignment Marks |
| *2 | Groove |
Reinstall the cylinder head cover.
|
| ||||
| OK | |
| 22.INSPECT SPARK PLUG |
Inspect the spark plug of the misfiring cylinder .
|
| ||||
| OK | |
| 23.CHECK FOR SPARK (SPARK TEST) |
Perform a spark test .
|
| ||||
| OK | |
| 24.CHECK CYLINDER COMPRESSION PRESSURE |
Measure the cylinder compression pressure of the misfiring cylinder .
|
| ||||
| OK | |
| 25.CHECK FUEL INJECTOR ASSEMBLY (POWER SOURCE) |
![]() |
Disconnect the fuel injector assembly connectors.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C7-1 - Body ground | Ignition switch ON | 11 to 14 V |
| C8-1 - Body ground | Ignition switch ON | 11 to 14 V |
| C9-1 - Body ground | Ignition switch ON | 11 to 14 V |
| C10-1 - Body ground | Ignition switch ON | 11 to 14 V |
| *1 | Front view of wire harness connector (to Fuel Injector Assembly) |
Turn the ignition switch off.
Reconnect the fuel injector assembly connectors.
|
| ||||
| OK | |
| 26.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM) |
Disconnect the fuel injector assembly connectors.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C7-2 - C24-108 (#10) | Always | Below 1 Ω |
| C9-2 - C24-107 (#20) | Always | Below 1 Ω |
| C8-2 - C24-106 (#30) | Always | Below 1 Ω |
| C10-2 - C24-105 (#40) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| C7-2 or C24-108 (#10) - Body ground | Always | 10 kΩ or higher |
| C9-2 or C24-107 (#20) - Body ground | Always | 10 kΩ or higher |
| C8-2 or C24-106 (#30) - Body ground | Always | 10 kΩ or higher |
| C10-2 or C24-105 (#40) - Body ground | Always | 10 kΩ or higher |
Reconnect the fuel injector assembly connectors.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 27.INSPECT FUEL INJECTOR ASSEMBLY OF MISFIRING CYLINDER |
Inspect the fuel injector assembly injection (whether fuel volume is high or low, and whether injection pattern is poor) (Click here).
|
| ||||
| OK | |
| 28.CHECK VALVE CLEARANCE OF MISFIRING CYLINDER |
Check the valve clearance (Click here).
|
| ||||
| OK | |
| 29.CHECK HARNESS AND CONNECTOR |
Check the connection and terminal contact pressure of connectors and wire harness between the mass air flow meter and ECM (Click here).
| NEXT | |
| 30.PERFORM CONFIRMATION DRIVING PATTERN |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs (Click here).
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
| NEXT | |
| 31.CHECK WHETHER DTC OUTPUT RECURS (DTC P0300, P0301, P0302, P0303, P0304) |
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0300, P0301, P0302, P0303 or P0304.
Check the DTC judgment result.
| Result | Proceed to |
| ABNORMAL (DTC P0300, P0301, P0302, P0303 or P0304 is output) | A |
| NORMAL (DTC is not output) | B |
|
| ||||
| A | |
| 32.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER SUB-ASSEMBLY - ECM) |
Disconnect the mass air flow meter sub-assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| C2-5 (VG) - C24-118 (VG) | Always | Below 1 Ω |
| C2-4 (E2G) - C24-116 (E2G) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| C2-5 (VG) or C24-118 (VG) - Body ground | Always | 10 kΩ or higher |
Reconnect the ECM connector.
Reconnect the mass air flow meter sub-assembly connector.
|
| ||||
| OK | |
| 33.REPLACE MASS AIR FLOW METER |
Replace the mass air flow meter (Click here).
| NEXT | |
| 34.PERFORM CONFIRMATION DRIVING PATTERN |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON.
Turn the tester on.
Clear the DTCs (Click here).
Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.
| NEXT | |
| 35.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
Input the DTC: P0300, P0301, P0302, P0303 or P0304.
Check the DTC judgment result.
| Result | Proceed to |
| NORMAL (DTC is not output) | A |
| ABNORMAL (DTC P0300, P0301, P0302, P0303 or P0304 is output) | B |
|
| ||||
| A | ||
| ||
| 36.CHANGE TO NORMAL SPARK PLUG AND CHECK SPARK OF MISFIRING CYLINDER |
Change the installed spark plug to a known good spark plug.
Perform a spark test .
|
| ||||
| OK | ||
| ||
| 37.CHANGE TO NORMAL IGNITION COIL ASSEMBLY AND CHECK SPARK OF MISFIRING CYLINDER |
Change the installed ignition coil assembly to a known good ignition coil assembly.
Perform a spark test .
|
| ||||
| OK | ||
| ||
| 38.CHECK FUEL LINE |
Check the fuel lines for leaks or blockage.
|
| ||||
| OK | ||
| ||