DTC P0351 Ignition Coil "A" Primary / Secondary Circuit |
DTC P0352 Ignition Coil "B" Primary / Secondary Circuit |
DTC P0353 Ignition Coil "C" Primary / Secondary Circuit |
DTC P0354 Ignition Coil "D" Primary / Secondary Circuit |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0351 P0352 P0353 P0354 | No IGF signal to ECM while engine running (1 trip detection logic) |
|

| Item | Content |
| Terminals | CH1: IGT1, IGT2, IGT3, IGT4 - E1 CH2: IGF1 - E1 |
| Equipment Settings | 2 V/DIV. 20 ms./DIV. |
| Conditions | Cranking or idling |


| 1.INSPECT IGNITION COIL ASSEMBLY (POWER SOURCE) |
![]() |
Disconnect the C11 to C14 ignition coil connectors.
Measure the resistance between the terminals of the wire harness side connectors.
| Tester Connection | Specified Condition |
| GND (C11-4) - Body ground | Below 1 Ω |
| GND (C13-4) - Body ground | |
| GND (C12-4) - Body ground | |
| GND (C14-4) - Body ground |
Turn the ignition switch to the ON position.
Measure the voltage between the terminals of the wire harness side connectors.
| Tester Connection | Specified Condition |
| +B (C11-1) - GND (C11-4) | 9 to 14 V |
| +B (C13-1) - GND (C13-4) | |
| +B (C12-1) - GND (C12-4) | |
| +B (C14-1) - GND (C14-4) |
Reconnect the ignition coil connectors.
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM) |
![]() |
Disconnect the C11 to C14 ignition coil connectors.
Disconnect the C24 ECM connector.
Measure the resistance between the terminals of the wire harness side connectors.
| Tester Connection | Specified Condition |
| IGF (C11-2) - IGF1 (C24-81) | Below 1 Ω |
| IGF (C13-2) - IGF1 (C24-81) | |
| IGF (C12-2) - IGF1 (C24-81) | |
| IGF (C14-2) - IGF1 (C24-81) |
| Tester Connection | Specified Condition |
| IGT1 (C11-3) - IGT1 (C24-85) | Below 1 Ω |
| IGT2 (C13-3) - IGT2 (C24-84) | |
| IGT3 (C12-3) - IGT3 (C24-83) | |
| IGT4 (C14-3) - IGT4 (C24-82) |
| Tester Connection | Specified Condition |
| IGF (C11-2) or IGF1 (C24-81) - Body ground | 10 kΩ or higher |
| IGF (C13-2) or IGF1 (C24-81) - Body ground | |
| IGF (C12-2) or IGF1 (C24-81) - Body ground | |
| IGF (C14-2) or IGF1 (C24-81) - Body ground |
| Tester Connection | Specified Condition |
| IGT1 (C11-3) or IGT1 (C24-85) - Body ground | 10 kΩ or higher |
| IGT2 (C13-3) or IGT2 (C24-84) - Body ground | |
| IGT3 (C12-3) or IGT3 (C24-83) - Body ground | |
| IGT4 (C14-3) or IGT4 (C24-82) - Body ground |
Reconnect the ECM connector.
Reconnect the ignition coil connectors.
|
| ||||
| OK | |
| 3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0351, P0352, P0353 OR P0354) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and turn the tester on.
Clear the DTCs (Click here).
Shuffle arrangement of the ignition coils with igniters (among No. 1 to No. 4 cylinders).
Perform a simulation test.
Check the DTCs displayed on the tester.
| Display (DTC Output) | Proceed to |
| Same DTC output | A |
| Different ignition coil DTC output | B |
|
| ||||
| A | ||
| ||