Home › ENGINE · 2AZ-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0351    Ignition Coil "A" Primary / Secondary Circuit

DTC    P0352    Ignition Coil "B" Primary / Secondary Circuit

DTC    P0353    Ignition Coil "C" Primary / Secondary Circuit

DTC    P0354    Ignition Coil "D" Primary / Secondary Circuit

for Preparation Click here


DESCRIPTION

HINT:
  1. These DTCs indicate malfunctions relating to the primary circuit.
  2. If DTC P0351 is set, check the No. 1 ignition coil assembly circuit.
  3. If DTC P0352 is set, check the No. 2 ignition coil assembly circuit.
  4. If DTC P0353 is set, check the No. 3 ignition coil assembly circuit.
  5. If DTC P0354 is set, check the No. 4 ignition coil assembly circuit.

A direct ignition system is used on this vehicle.
The direct ignition system is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil assembly and a spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. Spark of the spark plugs passes from the center electrode to the ground electrodes.
The ECM determines the ignition timing and transmits the ignition signals (IGT) to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches on and off the current to the primary coil. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil, the igniter sends back an ignition confirmation signal (IGF) to the ECM, for each cylinder ignition.

A204461E10


DTC No.
DTC Detection Condition
Trouble Area
P0351
P0352
P0353
P0354
No IGF signal to ECM while engine running
(1 trip detection logic)
  1. Ignition system
  2. Open or short in IGF1 or IGT circuit (1 to 4) between ignition coil assembly and ECM
  3. No. 1 to No. 4 ignition coil assemblies
  4. ECM

  1. A122717E03
    Reference: Inspection using an oscilloscope
  2. While cranking or idling the engine, check the waveform between terminals IGT (1 to 4) and E1, and IGF1 and E1 of the ECM connectors.

    HINT:
    The wavelength becomes shorter as the engine speed increases.

    Item
    Content
    ECM Terminal Names
    (1) Between IGT (1 to 4) and E1
    (2) Between IGF1 and E1
    Tester Range
    2 V/DIV., 20 ms./DIV.
    Condition
    Idling with warm engine

WIRING DIAGRAM


A142852E05


A142853E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ OUTPUT DTC
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / DTC.

  1. Read the DTCs.


Result:

Result
Proceed to
One of DTCs P0351, P0352, P0353 and P0354 is output.
A
Some of DTCs P0351, P0352, P0353 and P0354 are output.
B



B
Go to step 5
A


2.PERFORM SIMULATION TEST
  1. Clear the DTC (Click here).

  1. Change the arrangement of the ignition coil assemblies.

    NOTICE:
    Do not change the location of the connectors.

  1. Perform a simulation test.

    Result:

    Result
    Proceed to
    Same DTCs are output (same as DTCs that were cleared)
    A
    Other DTCs are output
    B



B
REPLACE IGNITION COIL ASSEMBLY (Click here)
A


3.INSPECT IGNITION COIL ASSEMBLY (POWER SOURCE)


    A194110E41
  1. Disconnect the ignition coil assembly connectors.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C11-1 (+B) - C11-4 (GND)
    Ignition switch ON
    11 to 14 V
    C12-1 (+B) - C12-4 (GND)
    Ignition switch ON
    11 to 14 V
    C13-1 (+B) - C13-4 (GND)
    Ignition switch ON
    11 to 14 V
    C14-1 (+B) - C14-4 (GND)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Ignition Coil Assembly)

  1. Reconnect the ignition coil assembly connectors.



NG
Go to step 5
OK


4.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
  1. Disconnect the ignition coil assembly connectors.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):

    Tester Connection
    Condition
    Specified Condition
    C11-3 (IGT1) - C24-85 (IGT1)
    Always
    Below 1 Ω
    C13-3 (IGT2) - C24-84 (IGT2)
    Always
    Below 1 Ω
    C12-3 (IGT3) - C24-83 (IGT3)
    Always
    Below 1 Ω
    C14-3 (IGT4) - C24-82 (IGT4)
    Always
    Below 1 Ω
    C11-2 (IGF) - C24-81 (IGF1)
    Always
    Below 1 Ω
    C12-2 (IGF) - C24-81 (IGF1)
    Always
    Below 1 Ω
    C13-2 (IGF) - C24-81 (IGF1)
    Always
    Below 1 Ω
    C14-2 (IGF) - C24-81 (IGF1)
    Always
    Below 1 Ω


    Standard Resistance (Check for Short):

    Tester Connection
    Condition
    Specified Condition
    C11-3 (IGT1) or C24-85 (IGT1) - Body ground
    Always
    10 kΩ or higher
    C13-3 (IGT2) or C24-84 (IGT2) - Body ground
    Always
    10 kΩ or higher
    C12-3 (IGT3) or C24-83 (IGT3) - Body ground
    Always
    10 kΩ or higher
    C14-3 (IGT4) or C24-82 (IGT4) - Body ground
    Always
    10 kΩ or higher
    C11-2 (IGF) or C24-81 (IGF1) - Body ground
    Always
    10 kΩ or higher
    C12-2 (IGF) or C24-81 (IGF1) - Body ground
    Always
    10 kΩ or higher
    C13-2 (IGF) or C24-81 (IGF1) - Body ground
    Always
    10 kΩ or higher
    C14-2 (IGF) or C24-81 (IGF1) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ignition coil assembly connectors.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION COIL ASSEMBLY - ECM)
OK

REPLACE ECM (Click here)  

5.INSPECT IGNITION COIL ASSEMBLY (GROUND CIRCUIT)


    A194110E42
  1. Disconnect the ignition coil assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    C11-4 (GND) - Body ground
    Always
    Below 1 Ω
    C12-4 (GND) - Body ground
    Always
    Below 1 Ω
    C13-4 (GND) - Body ground
    Always
    Below 1 Ω
    C14-4 (GND) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Ignition Coil Assembly)

  1. Reconnect the ignition coil assembly connectors.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION COIL ASSEMBLY - BODY GROUND)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (IGNITION COIL ASSEMBLY - IG2 RELAY)