Home › ENGINE · 2GR-FE › ENGINE CONTROL SYSTEM › SFI SYSTEM

DTC    P0351    Ignition Coil "A" Primary / Secondary Circuit

DTC    P0352    Ignition Coil "B" Primary / Secondary Circuit

DTC    P0353    Ignition Coil "C" Primary / Secondary Circuit

DTC    P0354    Ignition Coil "D" Primary / Secondary Circuit

DTC    P0355    Ignition Coil "E" Primary / Secondary Circuit

DTC    P0356    Ignition Coil "F" Primary / Secondary Circuit

for Preparation Click here


DESCRIPTION

HINT:
  1. These DTCs indicate malfunctions relating to the primary circuit.
  2. If DTC P0351 is set, check the No. 1 ignition coil circuit.
  3. If DTC P0352 is set, check the No. 2 ignition coil circuit.
  4. If DTC P0353 is set, check the No. 3 ignition coil circuit.
  5. If DTC P0354 is set, check the No. 4 ignition coil circuit.
  6. If DTC P0355 is set, check the No. 5 ignition coil circuit.
  7. If DTC P0356 is set, check the No. 6 ignition coil circuit.

A Direct Ignition System (DIS) is used on this vehicle.
The DIS is a 1-cylinder ignition system in which each cylinder is ignited by one ignition coil and spark plug is connected to the end of each secondary wiring. A powerful voltage, generated in the secondary wiring, is applied directly to each spark plug. The sparks of the spark plugs pass from the center electrode to the ground electrodes.
The ECM determines the ignition timing and transmits the ignition signals (IGT) to each cylinder. Using the IGT signal, the ECM turns the power transistor inside the igniter on and off. The power transistor, in turn, switches on and off the current to the primary coil. When the current to the primary coil is cut off, a powerful voltage is generated in the secondary coil. This voltage is applied to the spark plugs, causing them to spark inside the cylinders. As the ECM cuts the current to the primary coil off, the igniter sends back an ignition confirmation signal (IGF) to the ECM, for each cylinder ignition.

A133853E16


DTC No.
DTC Detection Condition
Trouble Area
P0351
P0352
P0353
P0354
P0355
P0356
No IGF signal to ECM while engine is running
(1 trip detection logic)
  1. Ignition system
  2. Open or short in IGF1 or IGT (1 to 6) circuit between ignition coil and ECM
  3. No. 1 to No. 6 ignition coils
  4. ECM

  1. A140641E02
    Reference: Inspection using an oscilloscope.
  2. While cranking or idling the engine, check the waveform between terminals IGT (1 to 6) and E1, and IGF1 and E1 of the ECM connector.
    Item
    Content
    Terminals
    CH1: IGT1, IGT2, IGT3, IGT4, IGT5, IGT6 - E1
    CH2: IGF1 - E1
    Equipment Settings
    2 V/DIV.
    20 ms./DIV.
    Conditions
    Cranking or idling

WIRING DIAGRAM


A241186E01


A141114E02


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can be helpful in determining whether the vehicle was running or stopped, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, as well as other data recorded at the time of a malfunction (Click here).

1.INSPECT IGNITION COIL ASSEMBLY (POWER SOURCE)


    A054393E66
  1. Disconnect the C11, C13, C12, C14, C38 or C39 ignition coil connector.

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Specified Condition
    C11-1 - Body ground
    11 to 14 V
    C13-1 - Body ground
    11 to 14 V
    C12-1 - Body ground
    11 to 14 V
    C14-1 - Body ground
    11 to 14 V
    C38-1 - Body ground
    11 to 14 V
    C39-1 - Body ground
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Specified Condition
    C11-4 - Body ground
    Below 1 Ω
    C13-4 - Body ground
    Below 1 Ω
    C12-4 - Body ground
    Below 1 Ω
    C14-4 - Body ground
    Below 1 Ω
    C38-4 - Body ground
    Below 1 Ω
    C39-4 - Body ground
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK HARNESS AND CONNECTOR (IGNITION COIL ASSEMBLY - ECM (IGT SIGNAL TERMINAL))


    A105983E36
  1. Disconnect the C11, C13, C12, C14, C38 or C39 ignition coil connector.

  1. Disconnect the ECM C58 (RHD) or C55 (LHD) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance (Check for open):
    RHD:
    Tester Connection
    Specified Condition
    IGT1 (C11-3) - IGT1 (C58-40)
    Below 1 Ω
    IGT2 (C13-3) - IGT2 (C58-39)
    Below 1 Ω
    IGT3 (C12-3) - IGT3 (C58-38)
    Below 1 Ω
    IGT4 (C14-3) - IGT4 (C58-37)
    Below 1 Ω
    IGT5 (C38-3) - IGT5 (C58-36)
    Below 1 Ω
    IGT6 (C39-3) - IGT6 (C58-35)
    Below 1 Ω
    LHD:
    Tester Connection
    Specified Condition
    IGT1 (C11-3) - IGT1 (C55-40)
    Below 1 Ω
    IGT2 (C13-3) - IGT2 (C55-39)
    Below 1 Ω
    IGT3 (C12-3) - IGT3 (C55-38)
    Below 1 Ω
    IGT4 (C14-3) - IGT4 (C55-37)
    Below 1 Ω
    IGT5 (C38-3) - IGT5 (C55-36)
    Below 1 Ω
    IGT6 (C39-3) - IGT6 (C55-35)
    Below 1 Ω


    Standard resistance (Check for short):
    RHD:
    Tester Connection
    Specified Condition
    IGT1 (C11-3) or IGT1 (C58-40) - Body ground
    10 kΩ or higher
    IGT2 (C13-3) or IGT2 (C58-39) - Body ground
    10 kΩ or higher
    IGT3 (C12-3) or IGT3 (C58-38) - Body ground
    10 kΩ or higher
    IGT4 (C14-3) or IGT4 (C58-37) - Body ground
    10 kΩ or higher
    IGT5 (C38-3) or IGT5 (C58-36) - Body ground
    10 kΩ or higher
    IGT6 (C39-3) or IGT6 (C58-35) - Body ground
    10 kΩ or higher
    LHD:
    Tester Connection
    Specified Condition
    IGT1 (C11-3) or IGT1 (C55-40) - Body ground
    10 kΩ or higher
    IGT2 (C13-3) or IGT2 (C55-39) - Body ground
    10 kΩ or higher
    IGT3 (C12-3) or IGT3 (C55-38) - Body ground
    10 kΩ or higher
    IGT4 (C14-3) or IGT4 (C55-37) - Body ground
    10 kΩ or higher
    IGT5 (C38-3) or IGT5 (C55-36) - Body ground
    10 kΩ or higher
    IGT6 (C39-3) or IGT6 (C55-35) - Body ground
    10 kΩ or higher


    Standard resistance (Check for open):
    RHD:
    Tester Connection
    Specified Condition
    IGF (C11-2) - IGF1 (C58-106)
    Below 1 Ω
    IGF (C13-2) - IGF1 (C58-106)
    Below 1 Ω
    IGF (C12-2) - IGF1 (C58-106)
    Below 1 Ω
    IGF (C14-2) - IGF1 (C58-106)
    Below 1 Ω
    IGF (C38-2) - IGF1 (C58-106)
    Below 1 Ω
    IGF (C39-2) - IGF1 (C58-106)
    Below 1 Ω
    LHD:
    Tester Connection
    Specified Condition
    IGF (C11-2) - IGF1 (C55-106)
    Below 1 Ω
    IGF (C13-2) - IGF1 (C55-106)
    Below 1 Ω
    IGF (C12-2) - IGF1 (C55-106)
    Below 1 Ω
    IGF (C14-2) - IGF1 (C55-106)
    Below 1 Ω
    IGF (C38-2) - IGF1 (C55-106)
    Below 1 Ω
    IGF (C39-2) - IGF1 (C55-106)
    Below 1 Ω


    Standard resistance (Check for short):
    RHD:
    Tester Connection
    Specified Condition
    IGF (C11-2) or IGF1 (C58-106) - Body ground
    10 kΩ or higher
    IGF (C13-2) or IGF1 (C58-106) - Body ground
    10 kΩ or higher
    IGF (C12-2) or IGF1 (C58-106) - Body ground
    10 kΩ or higher
    IGF (C14-2) or IGF1 (C58-106) - Body ground
    10 kΩ or higher
    IGF (C38-2) or IGF1 (C58-106) - Body ground
    10 kΩ or higher
    IGF (C39-2) or IGF1 (C58-106) - Body ground
    10 kΩ or higher
    LHD:
    Tester Connection
    Specified Condition
    IGF (C11-2) or IGF1 (C55-106) - Body ground
    10 kΩ or higher
    IGF (C13-2) or IGF1 (C55-106) - Body ground
    10 kΩ or higher
    IGF (C12-2) or IGF1 (C55-106) - Body ground
    10 kΩ or higher
    IGF (C14-2) or IGF1 (C55-106) - Body ground
    10 kΩ or higher
    IGF (C38-2) or IGF1 (C55-106) - Body ground
    10 kΩ or higher
    IGF (C39-2) or IGF1 (C55-106) - Body ground
    10 kΩ or higher

  1. Reconnect the ignition coil connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.PERFORM SIMULATION TEST
  1. Clear the DTC(s) (Click here).

  1. Change the arrangement of the ignition coils (with igniters).

    NOTICE:
    Do not change the location of the connectors.

  1. Perform a simulation test.

    Result:

    Display (DTC Output)
    Proceed to
    Same DTCs (that have been erased)
    A
    Other DTCs
    B



B
REPLACE IGNITION COIL ASSEMBLY (Click here)
A

REPLACE ECM (Click here)