DTC P0013 Camshaft Position "B" Actuator Circuit / Open (Bank 1) |
DTC P0023 Camshaft Position "B" Actuator Circuit / Open (Bank 2) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0013 | Open or short in OCV for exhaust camshaft (bank 1) circuit (1 trip detection logic) |
|
| P0023 | Open or short in OCV for exhaust camshaft (bank 2) circuit (1 trip detection logic) |
|

| 1.PERFORM ACTIVE TEST USING INTELLIGENT TESTER (OPERATE OCV) |
Connect the intelligent tester to the DLC3.
Start the engine and turn the tester on.
Warm up the engine.
Enter the following menus: Powertrain / Engine / Active Test / Active the VVT System (Bank 1) or Control the VVT System (Bank 2).
Check the engine speed while operating the Oil Control Valve (OCV) using the tester.
| Tester Operation | Specified Condition |
| OCV OFF | Normal engine speed |
| OCV ON | Engine idles roughly or stalls (soon after OCV switched from OFF to ON) |
|
| ||||
| OK | ||
| ||
| 2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY |
![]() |
Disconnect the C42 or C46 OCV connector.
Measure the resistance between the terminals of the OCV.
| Tester Connection | Condition | Specified Condition |
| 1 - 2 | 20°C (68°F) | 6.9 to 7.9 Ω |
Reconnect the OCV connector.
|
| ||||
| OK | ||
| ||
| 3.CHECK HARNESS AND CONNECTOR (OCV - ECM) |
![]() |
Disconnect the C42 or C46 OCV connector.
Disconnect the C58 (RHD) or C55 (LHD) ECM connector.
Measure the resistance between the terminals.
| Tester Connection | Specified Condition |
| OE1+ (C58-16) - C42-1 | Below 1 Ω |
| OE1- (C58-17) - C42-2 | Below 1 Ω |
| OE2+ (C58-14) - C46-1 | Below 1 Ω |
| OE2- (C58-15) - C46-2 | Below 1 Ω |
| Tester Connection | Specified Condition |
| OE1+ (C55-16) - C42-1 | Below 1 Ω |
| OE1- (C55-17) - C42-2 | Below 1 Ω |
| OE2+ (C55-14) - C46-1 | Below 1 Ω |
| OE2- (C55-15) - C46-2 | Below 1 Ω |
| Tester Connection | Specified Condition |
| OE1+ (C58-16) or C42-1 - Body ground | 10 kΩ or higher |
| OE1- (C58-17) or C42-2 - Body ground | 10 kΩ or higher |
| OE2+ (C58-14) or C46-1 - Body ground | 10 kΩ or higher |
| OE2- (C58-15) or C46-2 - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| OE1+ (C55-16) or C42-1 - Body ground | 10 kΩ or higher |
| OE1- (C55-17) or C42-2 - Body ground | 10 kΩ or higher |
| OE2+ (C55-14) or C46-1 - Body ground | 10 kΩ or higher |
| OE2- (C55-15) or C46-2 - Body ground | 10 kΩ or higher |
Reconnect the ECM connector.
Reconnect the OCV connector.
|
| ||||
| OK | ||
| ||