Home › ENGINE · 2GR-FE › STARTING › ENTRY AND START SYSTEM

ENTRY AND START SYSTEM > TERMINALS OF ECU

for Preparation Click here



CHECK MAIN BODY ECU (INSTRUMENT PANEL J/B)

B112605E03

  1. Disconnect the IR, IA, IK, ID, IF, IM E6, E7 and E8 ECU connectors.

  2. Measure the voltage and resistance of the wire harness side connector.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E7-6 (AM1) - Body ground
    L - Body ground
    +B power supply
    Always
    11 to 14 V
    E6-1 (AM2) - Body ground
    L - Body ground
    +B power supply
    Always
    11 to 14 V
    E7-17 (SSW1) - Body ground
    L - Body ground
    Engine switch signal
    Engine switch pushed
    Below 1 Ω
    E7-17 (SSW1) - Body ground
    L - Body ground
    Engine switch signal
    Engine switch not pushed
    10 kΩ or higher
    E7-16 (SSW2) - Body ground
    V - Body ground
    Engine switch signal
    Engine switch pushed
    Below 1 Ω
    E7-16 (SSW2) - Body ground
    V - Body ground
    Engine switch signal
    Engine switch not pushed
    10 kΩ or higher
    E8-1 (GND3) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    IR-9 (LIN1) - Body ground
    BE - Body ground
    LIN line
    Always
    10 kΩ or higher
    IA-1 (BATB) - Body ground
    B - Body ground
    +B Power supply
    Always
    11 to 14 V
    IF-10 (GND1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    IM-9 (GND2) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    E8-15 (CANN) - Body ground
    W - Body ground
    CAN Line
    Always
    10 kΩ or higher
    E8-16 (CANP) - Body ground
    B - Body ground
    CAN Line
    Always
    10 kΩ or higher
    E8-5 (CANH) - Body ground
    B - Body ground
    CAN Line
    Always
    10 kΩ or higher
    E8-6 (CANL) - Body ground
    W - Body ground
    CAN Line
    Always
    10 kΩ or higher
    IA-1 (ACC) - Body ground
    B - Body ground
    ACC power supply
    Always
    11 to 14 V
    IA-1 (IG) - Body ground
    B - Body ground
    IG power supply
    Always
    11 to 14 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the ECU connectors.

  4. Measure the voltage of the connector.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E7-22 (ACCD) - E8-1 (GND3)
    W - W-B
    ACC signal
    Engine switch on (ACC)
    Output voltage at terminal AM1 or AM2 is -2 V or more.
    E7-22 (ACCD) - E8-1 (GND3)
    W - W-B
    ACC signal
    Engine switch off
    Below 1 V
    E7-3 (IG1D) - E8-1 (GND3)
    P - W-B
    IG1 signal
    Engine switch on (IG)
    Output voltage at terminal AM1 or AM2 is -2 V or more.
    E7-3 (IG1D) - E8-1 (GND3)
    P - W-B
    IG1 signal
    Engine switch on (ACC)
    Below 1 V
    E6-11 (IG2D) - E8-1 (GND3)
    LG - W-B
    IG2 signal
    Engine switch on (IG)
    Output voltage at terminal AM1 or AM2 is -2 V or more.
    E6-11 (IG2D) - E8-1 (GND3)
    LG - W-B
    IG2 signal
    Engine switch on (ACC)
    Below 1 V
    IL-7 (STP) - E8-1 (GND3)
    L - W-B
    Stop light signal
    Brake pedal depressed
    Output voltage at terminal AM1 or AM2 is -2 V or more.
    IL-7 (STP) - E8-1 (GND3)
    L - W-B
    Stop light signal
    Brake pedal released
    Below 1 V
    E7-19 (SLR+) - E8-1 (GND3)
    BR - W-B
    Steering lock motor signal
    Steering lock motor operating
    Below 1 V
    E7-19 (SLR+) - E8-1 (GND3)
    BR - W-B
    Steering lock motor signal
    Steering lock motor does not operate
    Output voltage at terminal AM1 or AM2 is -2 V or more.
    E7-18 (SLP) - E8-1 (GND3)
    P - W-B
    Steering lock actuator position signal
    Steering lock is locked
    Pulse generation
    (See waveform 3)
    E7-18 (SLP) - E8-1 (GND3)
    P - W-B
    Steering lock actuator position signal
    Steering lock is released
    Pulse generation
    (See waveform 3)
    E8-9 (SPD) - E8-1 (GND3)
    V - W-B
    Vehicle speed signal
    Engine switch on (IG), rotate rear wheel slowly
    Pulse generation
    (See waveform 1)
    E8-8 (TACH) - E8-1 (GND3)
    B - W-B
    Tachometer signal
    Engine running
    Pulse generation
    (See waveform 2)
    E9-2 (P) - E8-1 (GND3)
    G - W-B
    Shift lock signal
    Shift lever P position
    Output voltage at terminal AM1 or AM2 is -2 V or more.
    E9-2 (P) - E8-1 (GND3)
    G - W-B
    Shift lock signal
    Shift lever not P position
    Below 1 V
    E6-3 (ACCR) - E8-1 (GND3)
    P - W-B
    Starter assist signal
    Brake pedal depressed, shift lever P position, engine switch is pushed once → on (IG)
    0.1 to 0.8 V *1
    → Output voltage at terminal AM1 or AM2 is -2 V or more.
    E9-4 (STSW) - E8-1 (GND3)
    GR - W-B
    Starter activation request signal
    Brake pedal depressed, engine switch held on (ST)
    Output voltage at terminal AM1 or AM2 is -2 V or more.
    E7-8 (STR) - E8-1 (GND3)
    G - W-B
    Park/neutral position switch
    Engine switch on (IG), Shift lever except P or N position → P or N position
    Below 1 V → Pulse generation *3
    E9-6 (STR2) - E8-1 (GND3)
    V - W-B
    Starter signal (Sub)
    Brake pedal depressed, shift lever P or N position, engine switch on (ST)
    Output voltage at terminal AM1 or AM2 is -3.5 V or more. *2
    E7-15 (INDS) - E8-1 (GND3)
    LG - W-B
    Vehicle condition signal
    Brake pedal depressed, shift lever P position.
    Output voltage at terminal AM1 or AM2 is -3 V or more.
    E7-14 (INDW) - E8-1 (GND3)
    P - W-B
    Warning signal
    Brake pedal depressed, shift lever P position, engine switch on (ACC, IG)
    Output voltage at terminal AM1 or AM2 is -3 V or more.
    E7-25 (SWIL) - E8-1 (GND3)
    BE - W-B
    Illumination signal
    Light control switch TAIL or HEAD
    Output voltage at terminal AM1 or AM2 is -2 V or more.

    HINT:
    *1: Voltage is output only when the engine is cranking.
    *2: Voltage is output for 0.3 seconds when the engine is cranking to start. Disconnect the C55 connector from the ECM and ST CUT relay before measuring the voltage.
    *3: Remove the ST CUT relay before measuring the voltage.

    If the result is not as specified, the ECU may have a malfunction.



  5. Using an oscilloscope, check the signal waveform of the ECU.



      I042329E01
    1. Waveform 1
      Waveform 1 (Reference): 
      Terminal No.
      E8-9 (SPD) - Body ground
      Tool Setting
      5 V/DIV., 10 ms./DIV.
      Vehicle Condition
      Driving at approx. 20 km/h (12 mph)

      HINT:
      As the vehicle speed increases, the wavelength shortens.



    2. I042330E01
    3. Waveform 2
      Waveform 2 (Reference): 
      Terminal No.
      E8-8 (TACH) - Body ground
      Tool Setting
      5 V/DIV., 10 ms./DIV.
      Vehicle Condition
      Engine idling

      HINT:
      As the engine revolution speed increases, the wavelength shortens.



    4. A130277E01
    5. Waveform 3
      Waveform 3 (Reference): 
      Terminal No.
      E7-18 (SLP) - Body ground
      Tool Setting
      2 V/DIV., 100 ms./DIV.
      Vehicle Condition
      Steering lock/unlock


CHECK CERTIFICATION ECU

E125964E14

  1. Disconnect the E74 ECU connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E74-1 (+B) - Body ground
    W - Body ground
    +B power supply
    Always
    11 to 14 V
    E74-10 (LIN) - Body ground
    BE - Body ground
    LIN line
    Always
    10 kΩ or higher
    E74-17 (E) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the ECU connector.

  4. Measure the voltage of the connector.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E74-18 (IG) - Body ground
    LG - Body ground
    Ignition power supply
    Engine switch on (IG)
    11 to 14 V
    E74-18 (IG) - Body ground
    LG - Body ground
    Ignition power supply
    Engine switch off
    Below 1 V
    If the result is not as specified, the ECU may have a malfunction.


CHECK ECM (for LHD)

B193552E11

  1. Disconnect the C55 and A55 ECM connectors.

  2. Measure the voltage and resistance of the wire harness side connectors.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A55-2 (+B) - Body ground
    R - Body ground
    Power source of ECM
    Engine switch on (IG)
    11 to 14 V
    A55-1 (+B2) - Body ground
    R - Body ground
    Power source of ECM
    Engine switch on (IG)
    11 to 14 V
    A55-28 (IGSW) - Body ground
    Y - Body ground
    Ignition switch signal
    Engine switch on (IG)
    11 to 14 V
    C55-22 (E01) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    C55-21 (E02) - Body ground
    B-W - Body ground
    Ground
    Always
    Below 1 Ω
    C55-104 (E03) - Body ground
    B - Body ground
    Ground
    Always
    Below 1 Ω
    C55-23 (E04) - Body ground
    W - Body ground
    Ground
    Always
    Below 1 Ω
    C55-46 (E05) - Body ground
    W - Body ground
    Ground
    Always
    Below 1 Ω
    C55-81 (E1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    C55-20 (ME01) - Body ground
    B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the ECM connectors.

  4. Measure the voltage of the connectors.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A55-48 (STA) - C55-81 (E1)
    V - W-B
    Starter relay operation signal
    Cranking
    11 to 14 V
    A55-13 (ACCR) - C55-81 (E1)
    R - W-B
    ACC relay cut signal (output)
    Brake pedal depressed, shift lever P position, engine switch is pushed once → on (IG)
    0.1 to 0.8 V *1 → Output voltage at terminal AM1 or AM2 is -2 V or more.
    A55-15 (TACH) - C55-81 (E1)
    B - W-B
    Engine revolution signal (output)
    Idling
    Pulse generation (see waveform 1)
    A55-36 (STP) - C55-81 (E1)
    W - W-B
    Stop light switch signal (input)
    Brake pedal depressed
    7.5 to 14 V
    A55-36 (STP) - C55-81 (E1)
    W - W-B
    Stop light switch signal (input)
    Brake pedal released
    Below 1.5 V
    C55-63 (STAR) - C55-81 (E1)
    R - W-B
    Starter signal (Main)
    Brake pedal depressed, shift lever P or N position engine switch on (ST)
    11 to 14 V
    C55-62 (NSW) - C55-81 (E1)
    L-B - W-B
    PNP switch signal
    Shift lever P or N position → except P or N position
    Below 1 V → pulse generation
    A55-14 (STSW) - C55-81 (E1)
    R - W-B
    Starter activation request signal
    Brake pedal depressed, engine switch held on (ST)
    Output voltage at terminal AM1 or AM2 is -2 V or more.

    HINT:
    *1: Voltage is output only when the engine is cranking.

    If the result is not as specified, the ECM may have a malfunction.



  5. I042330E01
  6. Using an oscilloscope, check the signal waveform of the ECM.
    Waveform 1 (Reference): 
    Terminal No.
    A55-15 (TACH) - C55-81 (E1)
    Tool Setting
    5 V/DIV., 10 ms./DIV.
    Vehicle Condition
    Engine idling

    HINT:
    As the vehicle speed increases, the wavelength shortens.


CHECK ECM (for RHD)

B193552E10

  1. Disconnect the C58 and A24 ECM connectors.

  2. Measure the voltage and resistance of the wire harness side connectors.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A24-2 (+B) - Body ground
    R - Body ground
    Power source of ECM
    Engine switch on (IG)
    11 to 14 V
    A24-1 (+B2) - Body ground
    R - Body ground
    Power source of ECM
    Engine switch on (IG)
    11 to 14 V
    A24-28 (IGSW) - Body ground
    Y - Body ground
    Ignition switch signal
    Engine switch on (IG)
    11 to 14 V
    C58-22 (E01) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    C58-21 (E02) - Body ground
    B-W - Body ground
    Ground
    Always
    Below 1 Ω
    C58-104 (E03) - Body ground
    B - Body ground
    Ground
    Always
    Below 1 Ω
    C58-23 (E04) - Body ground
    W - Body ground
    Ground
    Always
    Below 1 Ω
    C58-46 (E05) - Body ground
    W - Body ground
    Ground
    Always
    Below 1 Ω
    C58-81 (E1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    C58-20 (ME01) - Body ground
    B - Body ground
    Ground
    Always
    Below 1 Ω
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the ECM connectors.

  4. Measure the voltage of the connectors.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A24-48 (STA) - C58-81 (E1)
    V - W-B
    Starter relay operation signal
    Cranking
    11 to 14 V
    A24-13 (ACCR) - C58-81 (E1)
    R - W-B
    ACC relay cut signal (output)
    Brake pedal depressed, shift lever P position, engine switch is pushed once → on (IG)
    0.1 to 0.8 V *1 → Output voltage at terminal AM1 or AM2 is -2 V or more.
    A24-15 (TACH) - C58-81 (E1)
    B - W-B
    Engine revolution signal (output)
    Idling
    Pulse generation (see waveform 1)
    A24-36 (STP) - C58-81 (E1)
    W - W-B
    Stop light switch signal (input)
    Brake pedal depressed
    7.5 to 14 V
    A24-36 (STP) - C58-81 (E1)
    W - W-B
    Stop light switch signal (input)
    Brake pedal released
    Below 1.5 V
    C58-63 (STAR) - C58-81 (E1)
    R - W-B
    Starter signal (Main)
    Brake pedal depressed, shift lever P or N position engine switch on (ST)
    11 to 14 V
    C58-62 (NSW) - C58-81 (E1)
    L-B - W-B
    PNP switch signal
    Shift lever P or N position → except P or N position
    Below 1 V → pulse generation
    A24-14 (STSW) - C58-81 (E1)
    R - W-B
    Starter activation request signal
    Brake pedal depressed, engine switch held on (ST)
    Output voltage at terminal AM1 or AM2 is -2 V or more.

    HINT:
    *1: Voltage is output only when the engine is cranking.

    If the result is not as specified, the ECM may have a malfunction.



  5. I042330E01
  6. Using an oscilloscope, check the signal waveform of the ECM.
    Waveform 1 (Reference): 
    Terminal No.
    A24-15 (TACH) - C58-81 (E1)
    Tool Setting
    5 V/DIV., 10 ms./DIV.
    Vehicle Condition
    Engine idling

    HINT:
    As the vehicle speed increases, the wavelength shortens.


CHECK STEERING LOCK ECU

B106649E35

  1. Disconnect the E69 ECU connector.

  2. Measure the voltage and resistance of the wire harness side connector.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E69-7 (B) - Body ground
    P - Body ground
    +B power supply
    Always
    11 to 14 V
    E69-6 (IG2) - Body ground
    B - Body ground
    Ignition power supply
    Engine switch on (IG)
    11 to 14 V
    E69-6 (IG2) - Body ground
    B - Body ground
    Ignition power supply
    Engine switch off
    Below 1 V
    E69-1 (GND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    E69-2 (SGND) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω

    1. If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the E69 ECU connector.

  4. Measure the voltage of the connector.

    Tester Connection
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E69-4 (SLP1) - E69-1 (GND)
    P - W-B
    Steering lock actuator position signal
    Steering is locked
    11 to 14 V
    E69-4 (SLP1) - E69-1 (GND)
    P - W-B
    Steering lock actuator position signal
    Steering is released
    Below 1 V

    1. If the result is not as specified, the ECU may have a malfunction.