ENTRY AND START SYSTEM > DATA LIST / ACTIVE TEST |
| READ DATA LIST |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Body / Data List.
Read the Data List according to the display on the intelligent tester.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| ACC SW | Engine switch on (ACC) / ON or OFF | ON: Engine switch on (ACC) OFF: Engine switch off | - |
| IG SW | Engine switch on (IG) / ON or OFF | ON: Engine switch on (IG) OFF: Engine switch off | - |
| Stop Light SW | Stop light switch / ON or OFF | ON: Brake pedal depressed OFF: Brake pedal released | - |
| St SW1 | Start switch 1 / ON or OFF | ON: Engine switch is pushed OFF: Engine switch is not pushed | - |
| St SW2 | Start switch 2 / ON or OFF | ON: Engine switch is pushed OFF: Engine switch is not pushed | - |
| Str Unlock SW | Steering lock condition / ON or OFF | ON: Steering is unlocked (Engine switch on (ACC)) OFF: Steering is locked (Engine switch off) | - |
| N SW / C SW | Neutral start switch / ON or OFF | ON: Shift position is P or N OFF: Shift position is neither P nor N | - |
| Shift P Sig | Shift P position signal / ON or OFF | ON: Shift position is P OFF: Shift position is not P | - |
| Vehicle Spd Sig | Vehicle speed signal / STOP or RUN | STOP: Vehicle is stopped RUN: Vehicle is running | - |
| E/G Cond | Engine condition / STOP or RUN | STOP: Engine is stopped RUN: Engine is running | - |
| IG1 Relay Mon 1 | IG1 outer relay monitor / ON or OFF | ON: Engine switch on (IG) OFF: Engine switch off | - |
| IG2 Relay Mon 1 | IG2 outer relay monitor / ON or OFF | ON: Engine switch on (IG) OFF: Engine switch off | - |
| IG1 Relay Mon 2 | IG1 inner relay monitor / ON or OFF | ON: Engine switch on (IG) OFF: Engine switch off | - |
| IG2 Relay Mon 2 | IG2 inner relay monitor / ON or OFF | ON: Engine switch on (IG) OFF: Engine switch off | - |
| ACC Relay Mon | ACC relay monitor / ON or OFF | ON: Engine switch on (ACC) OFF: Engine switch off | - |
| Latch Circuit | Latch circuit / ON or OFF | ON: Engine switch on (IG) or engine running OFF: Engine switch off or on (ACC) | - |
| Start Req Sig | Starter request signal monitor / ON or OFF | ON: ST relay is ON OFF: ST relay is OFF | Engine switch pressed and held with shift lever in P or N |
| Pwr Cond | Power supply condition / ALL, ACC ON, IG1 IG2, ST ON | ALL: All relays are OFF ACC ON: ACC relay is ON IG1: IG1 relay is ON IG2: IG2 relay is ON ST ON: ST request signal is ON | - |
| ACC Cut Sig | ACC relay cut signal / ON or OFF | ON: Engine is cranking OFF: Engine is not cranking | - |
| ST Relay Mon | STARTER relay monitor / ON or OFF | ON: Engine is cranking OFF: Engine is not cranking | Engine is cranking with engine switch on (IG) and shift lever in P or N |
| Comm Smrt/Wrls | Communication for certification ECU / OK or STOP | OK: Communication STOP: No communication | - |
| PERFORM ACTIVE TEST |
Connect the intelligent tester to the DLC3
Turn the engine switch on (IG).
Turn the intelligent tester on.
Enter the following menus: Body / Body / Active Test.
Perform the Active Test according to the display on the intelligent tester.
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Lighting Ind | Indicator for lighting | ON / OFF | - |
| Ind Condition | Engine switch indicator | Green / Amber / No Sig | - |
| S Lock Pwr | Power supply for steering lock ECU | ON / OFF | - |