DTC C0210/33 Rear Speed Sensor RH Circuit |
DTC C0215/34 Rear Speed Sensor LH Circuit |
DTC C1273/73 Low Output Signal of Rear Speed Sensor RH (Test Mode DTC) |
DTC C1274/74 Low Output Signal of Rear Speed Sensor LH (Test Mode DTC) |

| DTC No. | DTC Detection Condition | Trouble Area |
| C0210/33 C0215/34 | When any of the following is detected:
|
|

| 1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION) |
Using the intelligent tester, check for any momentary interruption in the wire harness and connector corresponding to a DTC (Click here).
| Item (Display) | Measurement Item / Range (Display) | Normal Condition |
| RR Speed Open | RR speed sensor open detection / ERROR or NORMAL | ERROR: Momentary interruption NORMAL: Normal |
| RL Speed Open | RL speed sensor open detection / ERROR or NORMAL | ERROR: Momentary interruption NORMAL: Normal |
| Condition | Proceed to |
| There are no momentary interruptions | A |
| There are momentary interruptions | B |
| There is a constant open circuit | C |
|
| ||||
|
| ||||
| A | |
| 2.READ VALUE USING INTELLIGENT TESTER (REAR SPEED SENSOR) |
Turn the ignition switch off.
Connect the intelligent tester to the DLC3.
Start the engine.
Select the Data List mode on the intelligent tester.
| Item (Display) | Measurement Item / Range (Display) | Normal Condition |
| RR Wheel Speed | RR wheel speed sensor reading / min.: 0 mph (0 km/h), max.: 202 mph (326 km/h) | Actual wheel speed |
| RL Wheel Speed | RL wheel speed sensor reading / min.: 0 mph (0 km/h), max.: 202 mph (326 km/h) | Actual wheel speed |
Check that there is no difference between the speed value output from the speed sensor displayed on the intelligent tester and the speed value displayed on the speedometer when driving the vehicle.
|
| ||||
| OK | |
| 3.PERFORM TEST MODE (SIGNAL CHECK) |
Perform sensor check in the Test Mode procedure (Click here).
|
| ||||
| OK | |
| 4.RECONFIRM DTC |
Turn the ignition switch off.
Clear the DTC (Click here).
Start the engine.
Drive the vehicle at the speed of 20 mph (32 km/h) or more for at least 60 seconds.
Check if the same DTC is recorded (Click here).
| Condition | Proceed to |
| DTCs (C0210/33 and/or C0215/34) are not output | A |
| DTCs (C0210/33 and/or C0215/34) are output | B |
|
| ||||
| A | ||
| ||
| 5.CHECK REAR SPEED SENSOR INSTALLATION |
![]() |
Turn the ignition switch off.
Check the speed sensor installation.
|
| ||||
| OK | |
| 6.INSPECT REAR SPEED SENSOR |
![]() |
Turn the ignition switch off.
Disconnect the rear speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| 2 (RR+) - 1 (RR-) | Always | 0.9 to 2.1 kΩ |
| 2 (RR+) - Body ground | Always | 10 kΩ or higher |
| 1 (RR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| 2 (RL+) - 1 (RL-) | Always | 0.9 to 2.1 kΩ |
| 2 (RL+) - Body ground | Always | 10 kΩ or higher |
| 1 (RL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (SKID CONTROL SENSOR WIRE) |
![]() |
Disconnect the skid control sensor wire.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| f1 ("A"-1) - f1 ("B"-2) | Always | Below 1 Ω |
| f1 ("A"-1) - f1 ("B"-1) | Always | 10 kΩ or higher |
| f1 ("A"-1) - Body ground | Always | 10 kΩ or higher |
| f1 ("A"-2) - f1 ("B"-1) | Always | Below 1 Ω |
| f1 ("A"-2) - f1 ("B"-2) | Always | 10 kΩ or higher |
| f1 ("A"-2) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| g1 ("A"-1) - g1 ("B"-2) | Always | Below 1 Ω |
| g1 ("A"-1) - g1 ("B"-1) | Always | 10 kΩ or higher |
| g1 ("A"-1) - Body ground | Always | 10 kΩ or higher |
| g1 ("A"-2) - g1 ("B"-1) | Always | Below 1 Ω |
| g1 ("A"-2) - g1 ("B"-2) | Always | 10 kΩ or higher |
| g1 ("A"-2) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 8.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR) |
![]() |
Disconnect the skid control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A26-5 (RR+) - f1-1 (RR+) | Always | Below 1 Ω |
| A26-5 (RR+) - Body ground | Always | 10 kΩ or higher |
| A26-19 (RR-) - f1-2 (RR-) | Always | Below 1 Ω |
| A26-19 (RR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| A26-20 (RL+) - g1-1 (RL+) | Always | Below 1 Ω |
| A26-20 (RL+) - Body ground | Always | 10 kΩ or higher |
| A26-6 (RL-) - g1-2 (RL-) | Always | Below 1 Ω |
| A26-6 (RL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 9.CHECK SPEED SENSOR AND SPEED SENSOR ROTOR SERRATIONS |
![]() |
Reconnect the skid control sensor wire.
Reconnect the the rear speed sensor connector.
Connect the oscilloscope to the rear speed sensor terminal of the skid control ECU.
Check that a waveform is output when the tires are rotated.
|
| ||||
| OK | |
| 10.RECONFIRM DTC |
Reconnect the skid control ECU connector.
Clear the DTC (Click here).
Start the engine.
Drive the vehicle at the speed of 20 mph (32 km/h) or more for at least 60 seconds.
Check if the same DTC is recorded (Click here).
| Condition | Proceed to |
| DTCs (C0210/33 and/or C0215/34) are output | A |
| DTCs (C0210/33 and/or C0215/34) are not output | B |
|
| ||||
| A | ||
| ||
| 11.REPAIR OR REPLACE HARNESS OR CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR) |
Turn the ignition switch off.
Repair or replace the harness or connector.
Check for any momentary interruption between the skid control ECU and rear speed sensor (Click here).
Check that there is no momentary interruption.
| NEXT | |
| 12.RECONFIRM DTC |
Clear the DTC (Click here).
Start the engine.
Drive the vehicle at the speed of 20 mph (32 km/h) or more for at least 60 seconds.
Check if the same DTC is recorded (Click here).
| Condition | Proceed to |
| DTCs (C0210/33 and/or C0215/34) are not output | A |
| DTCs (C0210/33 and/or C0215/34) are output | B |
|
| ||||
| A | ||
| ||