DTC P2237 Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 1 Sensor 1) |
DTC P2238 Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 1 Sensor 1) |
DTC P2239 Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 1 Sensor 1) |
DTC P2240 Oxygen (A/F) Sensor Pumping Current Circuit / Open (Bank 2 Sensor 1) |
DTC P2241 Oxygen (A/F) Sensor Pumping Current Circuit Low (Bank 2 Sensor 1) |
DTC P2242 Oxygen (A/F) Sensor Pumping Current Circuit High (Bank 2 Sensor 1) |
DTC P2252 Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 1 Sensor 1) |
DTC P2253 Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 1 Sensor 1) |
DTC P2255 Oxygen (A/F) Sensor Reference Ground Circuit Low (Bank 2 Sensor 1) |
DTC P2256 Oxygen (A/F) Sensor Reference Ground Circuit High (Bank 2 Sensor 1) |

| DTC No. | DTC Detection Condition | Trouble Area |
| P2237 P2240 | Open in the circuit between terminals AF+ and AF- of the air fuel ratio sensor while engine running. (2 trip detection logic) |
|
| P2238 P2241 |
(1 trip detection logic): (a) AF+ voltage is 0.5 V or less (b) (AF+) - (AF-) = 0.1 V or less
(2 trip detection logic) |
|
| P2239 P2242 | AF+ voltage is more than 4.5 V for 5.0 seconds or more (2 trip detection logic) |
|
| P2252 P2255 | AF- voltage is 0.5 V or less for 5.0 seconds or more (2 trip detection logic) |
|
| P2253 P2256 | AF- voltage is more than 4.5 V for 5.0 seconds or more (2 trip detection logic) |
|
| Tester Display (Sensor) | Injection Volume | Status | Voltage |
| AFS B1S1 or AFS B2S1 (A/F) | +25 % | Rich | Less than 3.1 V |
| AFS B1S1 or AFS B2S1 (A/F) | -12.5 % | Lean | More than 3.4 V |
| O2S B1S2 or O2S B2S2 (HO2) | +25 % | Rich | More than 0.55 V |
| O2S B1S2 or O2S B2S2 (HO2) | -12.5 % | Lean | Less than 0.4 V |
| Case | A/F Sensor (Sensor 1) Output Voltage | HO2 Sensor (Sensor 2) Output Voltage | Main Suspected Trouble Areas | ||
| 1 | Injection Volume +25 % -12.5 % | ![]() | Injection Volume +25 % -12.5 % | ![]() | - |
| Output Voltage More than 3.4 V Less than 3.1 V | ![]() | Output Voltage More than 0.55 V Less than 0.4 V | ![]() | ||
| 2 | Injection Volume +25 % -12.5 % | ![]() | Injection Volume +25 % -12.5 % | ![]() |
|
| Output Voltage Almost no reaction | ![]() | Output Voltage More than 0.55 V Less than 0.4 V | ![]() | ||
| 3 | Injection Volume +25 % -12.5 % | ![]() | Injection Volume +25 % -12.5 % | ![]() |
|
| Output Voltage More than 3.4 V Less than 3.1 V | ![]() | Output Voltage Almost no reaction | ![]() | ||
| 4 | Injection volume +25 % -12.5 % | ![]() | Injection Volume +25 % -12.5 % | ![]() |
|
| Output Voltage Almost no reaction | ![]() | Output Voltage Almost no reaction | ![]() | ||
| 1.INSPECT AIR FUEL RATIO SENSOR (HEATER RESISTANCE) |
![]() |
Disconnect the C15 or C35 A/F sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| HA1A (1) - +B (2) | 20°C (68°F) | 1.8 to 3.4 Ω |
| HA1A (1) - A1A- (4) | - | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| HA2A (1) - +B (2) | 20°C (68°F) | 1.8 to 3.4 Ω |
| HA2A (1) - A2A- (4) | - | 10 kΩ or higher |
Reconnect the A/F sensor connector.
|
| ||||
| OK | |
| 2.INSPECT A/F FUSE |
![]() |
Remove the A/F fuse from the engine room junction block.
Measure the A/F fuse resistance.
Reinstall the A/F fuse.
|
| ||||
| OK | |
| 3.INSPECT ENGINE ROOM JUNCTION BLOCK (A/F RELAY) |
![]() |
Remove the engine room junction block from the engine room R/B.
Inspect the A/F relay.
Measure the A/F relay resistance.
| Tester Connection | Specified Condition |
| 1G-1 - 1A-4 | 10 kΩ or higher |
| 1G-1 - 1A-4 | Below 1 Ω (Apply battery voltage between terminals 1E-6 and 1E-10) |
Reinstall the engine room junction block.
|
| ||||
| OK | |
| 4.CHECK HARNESS AND CONNECTOR (A/F SENSOR - ECM) |
![]() |
Disconnect the C15 and C35 A/F sensor connectors.
Turn the engine switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| +B (C15-2) - Body ground | 9 to 14 V |
| +B (C35-2) - Body ground | 9 to 14 V |
Turn the engine switch off.
Disconnect the C58 (RHD) or C55 (LHD) ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| HA1A (C15-1) - HA1A (C58-86) | Below 1 Ω |
| A1A+ (C15-3) - A1A+ (C58-93) | Below 1 Ω |
| A1A- (C15-4) - A1A- (C58-116) | Below 1 Ω |
| HA2A (C35-1) - HA2A (C58-109) | Below 1 Ω |
| A2A+ (C35-3) - A2A+ (C58-120) | Below 1 Ω |
| A2A- (C35-4) - A2A- (C58-119) | Below 1 Ω |
| Tester Connection | Specified Condition |
| HA1A (C15-1) - HA1A (C55-86) | Below 1 Ω |
| A1A+ (C15-3) - A1A+ (C55-93) | Below 1 Ω |
| A1A- (C15-4) - A1A- (C55-116) | Below 1 Ω |
| HA2A (C35-1) - HA2A (C55-109) | Below 1 Ω |
| A2A+ (C35-3) - A2A+ (C55-120) | Below 1 Ω |
| A2A- (C35-4) - A2A- (C55-119) | Below 1 Ω |
| Tester Connection | Specified Condition |
| HA1A (C15-1) or HA1A (C58-86) - Body ground | 10 kΩ or higher |
| A1A+ (C15-3) or A1A+ (C58-93) - Body ground | 10 kΩ or higher |
| A1A- (C15-4) or A1A- (C58-116) - Body ground | 10 kΩ or higher |
| HA2A (C35-1) or HA2A (C58-109) - Body ground | 10 kΩ or higher |
| A2A+ (C35-3) or A2A+ (C58-120) - Body ground | 10 kΩ or higher |
| A2A- (C35-4) or A2A- (C58-119)- Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| HA1A (C15-1) or HA1A (C55-86) - Body ground | 10 kΩ or higher |
| A1A+ (C15-3) or A1A+ (C55-93) - Body ground | 10 kΩ or higher |
| A1A- (C15-4) or A1A- (C55-116) - Body ground | 10 kΩ or higher |
| HA2A (C35-1) or HA2A (C55-109) - Body ground | 10 kΩ or higher |
| A2A+ (C35-3) or A2A+ (C55-120) - Body ground | 10 kΩ or higher |
| A2A- (C35-4) or A2A- (C55-119)- Body ground | 10 kΩ or higher |
Reconnect the ECM connector.
Reconnect the A/F sensor connector.

|
| ||||
| OK | |
| 5.REPLACE AIR FUEL RATIO SENSOR |
Replace the air fuel ration sensor (Click here).
| NEXT | |
| 6.PERFORM CONFIRMATION DRIVING PATTERN |
Drive the vehicle referring to the Confirmation Driving Pattern on DTC P2195 .
| NEXT | |
| 7.CHECK WHETHER DTC OUTPUT RECURS |
Connect intelligent tester to the DLC3.
Turn the engine switch on (IG).
Turn the tester on.
Select the following menu items: Powertrain / Engine and ECT / Trouble Codes / Pending.
Read pending DTCs.
| Result | Proceed to |
| No output | A |
| P2237, P2238, P2239, P2240, P2241, P2242, P2252, P2253, P2255 or P2256 | B |
|
| ||||
| A | ||
| ||