ENTRY AND START SYSTEM > TERMINALS OF ECU |
| CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) |
Disconnect the E74 certification ECU (smart key ECU assembly) connector.

Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| E74-1 (+B1) - Body ground | W - Body ground | +B power supply | Always | 11 to 14 V |
| E74-17 (E) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the E74 certification ECU (smart key ECU assembly) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| E74-3 (TSW1) - E74-17 (E) | GR - W-B*1 LG - W-B*2 | Entry lock switch (driver side) signal | Entry lock switch (driver side) not pushed | 11 to 14 V |
| E74-3 (TSW1) - E74-17 (E) | GR - W-B*1 LG - W-B*2 | Entry lock switch (driver side) signal | Entry lock switch (driver side) pushed | Below 2 V |
| E74-4 (TSW2) - E74-17 (E) | L - W-B*1 GR - W-B*2 | Entry lock switch (front passenger side) signal | Entry lock switch (front passenger side) not pushed | 11 to 14 V |
| E74-4 (TSW2) - E74-17 (E) | L - W-B*1 GR - W-B*2 | Entry lock switch (front passenger side) signal | Entry lock switch (front passenger side) pushed | Below 2 V |
| E74-5 (SEL1) - E74-17 (E) | V - W-B*1 P - W-B*2 | Touch sensor activation control signal | Move the key more than 5 m (16.4 ft.) away from the front door (driver side) | 11 to 14 V |
| E74-5 (SEL1) - E74-17 (E) | V - W-B*1 P - W-B*2 | Touch sensor activation control signal | Key brought close to door outside handle assembly | Below 1 V |
| E74-6 (SEL2) - E74-17 (E) | P - W-B*1 V - W-B*2 | Touch sensor activation control signal | Move the key more than 5 m (16.4 ft) away from the front door (front passenger side) | 11 to 14 V |
| E74-6 (SEL2) - E74-17 (E) | P - W-B*1 V - W-B*2 | Touch sensor activation control signal | Key brought close to door outside handle assembly | Below 1 V |
| E74-7 (TSW5) - E74-17 (E) | G - W-B | Luggage compartment door opener outer switch signal | Luggage compartment door opener outer switch OFF | 11 to 14 V |
| E74-7 (TSW5) - E74-17 (E) | G - W-B | Luggage compartment door opener outer switch signal | Luggage compartment door opener outer switch ON | Below 1 V |
| E74-11 (CLG5) - E74-12 (CG5B) | R - W | Indoor electrical key oscillator (front floor) sensor signal | 30 seconds after driver side door opened and closed, engine switch off | Below 1 V |
| E74-11 (CLG5) - E74-12 (CG5B) | R - W | Indoor electrical key oscillator (front floor) sensor signal | Within 30 seconds driver side door opened and closed, engine switch off | Alternating between 5 V and below 1 V |
| E74-13 (CLG6) - E74-14 (CG6B) | Y - B | Indoor electrical key oscillator (rear floor) sensor signal | 30 seconds after driver side door opened and closed, engine switch off | Below 1 V |
| E74-13 (CLG6) - E74-14 (CG6B) | Y - B | Indoor electrical key oscillator (rear floor) sensor signal | Within 30 seconds driver side door opened and closed, engine switch off | Alternating between 5 V and below 1 V |
| E74-15 (CLG7) - E74-16 (CG7B) | R - W | Indoor electrical key oscillator (luggage compartment) sensor signal | Luggage compartment door opener outer switch OFF | Below 1 V |
| E74-15 (CLG7) - E74-16 (CG7B) | R - W | Indoor electrical key oscillator (luggage compartment) sensor signal | Luggage compartment door opener outer switch ON | Alternating between 5 V and below 1 V |
| E74-18 (IG) - Body ground | LG - Body ground | Ignition power supply | Engine switch off | Below 1 V |
| E74-18 (IG) - Body ground | LG - Body ground | Ignition power supply | Engine switch on (IG) | 11 to 14 V |
| E74-19 (ACC) - Body ground | L - Body ground | ACC power supply | Engine switch off | Below 1 V |
| E74-19 (ACC) - Body ground | L - Body ground | ACC power supply | Engine switch on (ACC) | 11 to 14 V |
| E74-22 (SEN1) - E74-17 (E) | B - W-B*1 BE - W-B*2 | Touch sensor detection signal | Door outside handle assembly (driver side) touched | Below 2 V |
| E74-22 (SEN1) - E74-17 (E) | B - W-B*1 BE - W-B*2 | Touch sensor detection signal | Door outside handle assembly (driver side) not touched | 11 to 14 V |
| E74-23 (SEN2) - E74-17 (E) | BE - W-B*1 B - W-B*2 | Touch sensor detection signal | Door outside handle assembly (front passenger side) touched | Below 2 V |
| E74-23 (SEN2) - E74-17 (E) | BE - W-B*1 B - W-B*2 | Touch sensor detection signal | Door outside handle assembly (front passenger side) not touched | 11 to 14 V |
| E74-29 (RC0) - E74-17 (E) | G - W-B | Entry door control receiver power source | Engine switch off, all doors closed and electrical key switch on | 4.5 to 5.5 V |
| E74-29 (RC0) - E74-17 (E) | G - W-B | Entry door control receiver power source | Engine switch off, all doors closed and electrical key switch off | Below 1 V |
| E74-31 (CLG8) - E74-32 (CG8B) | V - P | Outside electrical key oscillator (luggage compartment) sensor signal | Luggage compartment door opener outer switch off | Below 1 V |
| E74-31 (CLG8) - E74-32 (CG8B) | V - P | Outside electrical key oscillator (luggage compartment) sensor signal | Luggage compartment door opener outer switch on | Alternating between 5 V and below 1 V |
| E74-33 (CLG1) - E74-34 (CG1B) | LG - L*1 GR - BR*2 | Door electrical key oscillator (driver side) sensor signal | All doors closed, all doors locked and engine switch off | Alternating between 5 V and below 1 V |
| E74-33 (CLG1) - E74-34 (CG1B) | LG - L*1 GR - BR*2 | Door electrical key oscillator (driver side) sensor signal | Door unlocked or door open | Below 1 V |
| E74-35 (CLG2) - E74-36 (CG2B) | GR - BR*1 LG - L*2 | Door electrical key oscillator (front passenger side) sensor signal | All doors closed, all doors locked and engine switch off | Alternating between 5 V and below 1 V |
| E74-35 (CLG2) - E74-36 (CG2B) | GR - BR*1 LG - L*2 | Door electrical key oscillator (front passenger side) sensor signal | Door unlocked or door open | Below 1 V |
| E74-37 (ASEL) - Body ground*3 | V - Body ground | Tuner select signal | Engine switch off, luggage compartment door opener outer switch is on | 4.5 to 5.5 V |
| E74-37 (ASEL) - Body ground*3 | V - Body ground | Tuner select signal | Engine switch off, luggage compartment door opener outer switch is off | Below 1 V |
| E74-38 (RDA) - E74-17 (E) | Y - W-B | Entry door control receiver data input signal | Engine switch off, all doors closed and electrical key switch off | 11 to 14 V |
| E74-38 (RDA) - E74-17 (E) | Y - W-B | Entry door control receiver data input signal | Engine switch off, all doors closed and electrical key switch on | Pulse generation |
| E74-38 (RDA) - Body ground | Y - Body ground | Tuner input signal | Engine switch off, all doors closed, the electrical key is not in the detection area | 11 to 14 V |
| E74-38 (RDA) - Body ground | Y - Body ground | Tuner input signal | The electrical key is in the detection area | Pulse generation |
| E74-39 (RSSI) - E74-17 (E) | R - W-B | Entry door control receiver electric wave existence signal | Engine switch off, all doors closed, the electrical key is not in the detection area | 11 to 14 V |
| E74-39 (RSSI) - E74-17 (E) | R - W-B | Entry door control receiver electric wave existence signal | Engine switch off, all doors closed, the electrical key is in the detection area | Below 1 V |
| CHECK MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY) |
Disconnect the IA, IF and IM instrument panel junction block assembly connectors.

Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| IA-1 (BATB) - Body ground | B - Body ground | +B (BATB) power supply | Always | 11 to 14 V |
| IF-10 (GND1) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
| IM-9 (GND2) - Body ground | W-B - Body ground | Ground | Always | Below 1 Ω |
Reconnect the IA, IF and IM instrument panel junction block assembly connectors.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| E6-5 (LSWR) - Body ground | GR - Body ground | Rear right door lock position switch input | Rear right door UNLOCK | Below 1 V |
| E6-5 (LSWR) - Body ground | GR - Body ground | Rear right door lock position switch input | Rear right door LOCK | 11 to 14 V (or pulse generation) |
| E6-7 (RCTY) - Body ground | GR - Body ground | Rear right door courtesy switch input | Rear right door CLOSED | 11 to 14 V (or pulse generation) |
| E6-7 (RCTY) - Body ground | GR - Body ground | Rear right door courtesy switch input | Rear right door OPEN | Below 1 V |
| E6-21 (PCTY) - Body ground | Y - Body ground*1 L - Body ground*2 | Passenger door courtesy switch input | Passenger door CLOSED | 11 to 14 V (or pulse generation) |
| E6-21 (PCTY) - Body ground | Y - Body ground*1 L - Body ground*2 | Passenger door courtesy switch input | Passenger door OPEN | Below 1 V |
| E6-25 (LGCY) - Body ground | W - Body ground | Luggage compartment door courtesy switch input | Luggage compartment door CLOSED | 11 to 14 V (or pulse generation) |
| E6-25 (LGCY) - Body ground | W - Body ground | Luggage compartment door courtesy switch input | Luggage compartment door OPEN | Below 1 V |
| E6-27 (LSWP) - Body ground | LG - Body ground*1 L - Body ground*2 | Passenger door lock position switch input | Passenger door UNLOCK | Below 1 V |
| E6-27 (LSWP) - Body ground | LG - Body ground*1 L - Body ground*2 | Passenger door lock position switch input | Passenger door LOCK | 11 to 14 V (or pulse generation) |
| E7-9 (LSWD) - Body ground | L - Body ground*1 Y - Body ground*2 | Driver door lock position switch input | Driver door UNLOCK | Below 1 V |
| E7-9 (LSWD) - Body ground | L - Body ground*1 Y - Body ground*2 | Driver door lock position switch input | Driver door LOCK | 11 to 14 V (or pulse generation) |
| E7-24 (DCTY) - Body ground | L - Body ground*1 Y - Body ground*2 | Driver door courtesy switch | Driver door CLOSED | 11 to 14 V (or pulse generation) |
| E7-24 (DCTY) - Body ground | L - Body ground*1 Y - Body ground*2 | Driver door courtesy switch | Driver door OPEN | Below 1 V |
| E8-2 (TCAN) - Body ground | BE - Body ground | Luggage compartment door lock cylinder input | Luggage compartment door lock cylinder FREE position | 11 to 14 V (or pulse generation) |
| E8-2 (TCAN) - Body ground | BE - Body ground | Luggage compartment door lock cylinder input | Luggage compartment door lock cylinder CANCEL position | Below 1 V |
| IO-7 (LCTY) - Body ground | LG - Body ground | Rear left door courtesy switch input | Rear left door CLOSED | 11 to 14 V (or pulse generation) |
| IO-7 (LCTY) - Body ground | LG - Body ground | Rear left door courtesy switch input | Rear left door OPEN | Below 1 V |
| IP-5 (LSWL) - Body ground | GR - Body ground | Rear left door lock position switch input | Rear left door UNLOCK | Below 1 V |
| IP-5 (LSWL) - Body ground | GR - Body ground | Rear left door lock position switch input | Rear left door LOCK | 11 to 14 V (or pulse generation) |
| COMBINATION METER ASSEMBLY |
Disconnect the F1 combination meter assembly connector.

Measure the voltage according to the value(s) in the table below.
| Tester Connection | Wiring Color | Terminal Description | Condition | Specified Condition |
| F1-1 (B) - Body ground | L - Body ground | Battery | Always | 11 to 14 V |
| F1-2 (B2) - Body ground | R - Body ground | Battery | Always | 11 to 14 V |
| F1-13 (IG+) - Body ground | GR - Body ground | Ignition switch signal | Engine switch off | Below 1 V |
| F1-13 (IG+) - Body ground | GR - Body ground | Ignition switch signal | Engine switch on (IG) | 11 to 14 V |
| F1-16 (FE) - Body ground | P - Body ground | Ground (Power ground) | Always | Below 1 V |
| F1-24 (ES) - Body ground | BR - Body ground | Ground (Signal ground) | Always | Below 1 V |