Home › COMMUNICATION SYSTEM › CAN COMMUNICATION › CAN COMMUNICATION SYSTEM (for LHD)

CAN COMMUNICATION SYSTEM (for LHD) > TERMINALS OF ECU

for Preparation Click here


NOTICE:
  1. Turn the ignition switch off before measuring the resistance of the CAN main wire and CAN branch wires.
  2. After the ignition switch is turned off, check that the key reminder warning system and lighting system are not operating.
  3. Before measuring the resistance, leave the vehicle as is for at least 1 minute and do not operate the ignition switch, any other switches or the doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

HINT:
Operating the ignition switch, any other switches or any triggers related ECU and sensor communication on the CAN, which would cause resistance reading variations.

NOTICE:
This section describes the standard CAN values for all CAN related components.


CAN No. 1 BUS JUNCTION CONNECTOR (NO. 1 CAN J/C, NO. 2 CAN J/C)


  1. No. 1 CAN J/C


    C142744E04


    No. 1 CAN J/C connectors ("A" side, with earth terminal)
    Connector Color
    Wire Color (CAN-H)
    Wire Color (CAN-L)
    CAN Main Bus Wire (E42)
    White
    B
    W
    Center Airbag Sensor (E45)
    Black
    B
    W

    No. 1 CAN J/C connectors ("B" side, with earth terminal)
    Connector Color
    Wire Color (CAN-H)
    Wire Color (CAN-L)
    Yaw Rate Sensor*1 (E46)
    Blue
    B
    W
    DLC3 (E62)
    Gray
    B
    W
    Steering Angle Sensor*1 (E63)
    Brown
    B
    W
    Combination Meter (E43)
    White
    B
    W
    Main Body ECU (E44)
    Black
    B
    W
    *1: w/ VSC



  2. No. 2 CAN J/C (REAR OF THE VEHICLE)


    C137762E02


    Terminals
    Wiring Color
    Connects to
    A40-1 (CANH)
    B
    ECM (CANH)
    A40-7 (CANL)
    W
    ECM (CANL)
    A40-2 (CANH)
    B
    Skid Control ECU (CANH)
    A40-8 (CANL)
    W
    Skid Control ECU (CANL)



  3. No. 2 CAN J/C (FRONT OF THE VEHICLE)


    C137763E40


    Terminals
    Wiring Color
    Connects to
    E41-2 (CANH)
    B
    A/C Amplifier (CANH)
    E41-8 (CANL)
    W
    A/C Amplifier (CANL)
    E41-4 (CANH)
    B
    No. 1 CAN J/C (CANH)
    E41-10 (CANL)
    W
    No. 1 CAN J/C (CANL)
    E41-5 (CANH)
    B
    Navigation ECU*2 (CANH)
    E41-11 (CANL)
    W
    Navigation ECU*2 (CANL)
    *2: w/ Navigation system



  4. The connection diagram of the components which are connected to the CAN J/C


    C209555E01


CAN MS BUS JUNCTION CONNECTOR (NO. 3 CAN J/C)


  1. No. 3 CAN J/C (w/ TOYOTA Parking assist-sensor system)


    C142735E04


    No. 3 CAN J/C connectors ("A" side, with earth terminal)
    Connector Color
    Wire Color (CAN-H)
    Wire Color (CAN-L)
    Certification ECU*3 (O33)
    Gray
    B
    W
    Main Body ECU (O32)
    White
    B
    W
    Clearance warning ECU (O31)
    Blue
    B
    W
    *3: w/ Entry and start system


DLC3


    C125062E02
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E10-6 (CANH) - E10-14 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Ignition Switch off
    54 to 69 Ω
    E10-6 (CANH) - E10-4 (CG)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    E10-14 (CANL) - E10-4 (CG)
    W - W-B
    LOW-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    E10-6 (CANH) - E10-16 (BAT)
    B - L
    HIGH-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    E10-14 (CANL) - E10-16 (BAT)
    W - L
    LOW-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


SKID CONTROL ECU (w/o VSC)


    C131970E11
  1. Disconnect the A25 skid control ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A25-26 (CANH) - A25-15 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Ignition Switch off
    54 to 69 Ω
    A25-26 (CANH) - A25-4 (GND1)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    A25-15 (CANL) - A25-4 (GND1)
    W - W-B
    LOW-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    A25-26 (CANH) - A25-3 (+BS)
    B - L
    HIGH-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    A25-15 (CANL) - A25-3 (+BS)
    W - L
    LOW-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


SKID CONTROL ECU WITH ACTUATOR (w/ VSC)


    E069126E52
  1. Disconnect the A26 skid control ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    A26-11 (CANH) - A26-25 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Ignition Switch off
    54 to 69 Ω
    A26-11 (CANH) - A26-32 (GND1)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    A26-25 (CANL) - A26-32 (GND1)
    W - W-B
    LOW-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    A26-11 (CANH) - A26-31 (+BS)
    B - L
    HIGH-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    A26-25 (CANL)- A26-31 (+BS)
    W - L
    LOW-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


STEERING ANGLE SENSOR (w/ VSC)


    G026357E15
  1. Disconnect the E17 steering angle sensor connector.

  2. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E17-10 (CANH) - E17-9 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Ignition Switch off
    54 to 69 Ω
    E17-10 (CANH) - E17-2 (ESS)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    E17-9 (CANL) - E17-2 (ESS)
    W - W-B
    LOW-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    E17-10 (CANH) - E17-3 (BAT)
    B - W
    HIGH-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    E17-9 (CANL) - E17-3 (BAT)
    W - W
    LOW-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


YAW RATE SENSOR (w/ VSC)


    G026641E19
  1. Disconnect the E34 yaw rate sensor connector.

  2. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E34-3 (CANH) - E34-2 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Ignition Switch off
    54 to 69 Ω
    E34-3 (CANH) - E34-1 (GND)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    E34-2 (CANL) - E34-1 (GND)
    W - W-B
    LOW-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    E34-3 (CANH) - E10-16 (BAT)
    B - L
    HIGH-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    E34-2 (CANL) - E10-16 (BAT)
    W - L
    LOW-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


CENTER AIRBAG SENSOR ASSEMBLY


    C125063E05
  1. Disconnect the E30 center airbag sensor assembly connector.

  2. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E30-13 (CANH) - E30-22 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Ignition Switch off
    54 to 69 Ω
    E30-13 (CANH) - E30-25 (E1)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    E30-22 (CANL) - E30-25 (E1)
    W - W-B
    LOW-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    E30-13 (CANH) - E10-16 (BAT)
    B - L
    HIGH-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    E30-22 (CANL) - E10-16 (BAT)
    W - L
    LOW-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


ECM


  1. Disconnect the A24 and C58 ECM connector.


    A107881E50



  2. 2AZ-FE

    1. Disconnect the A24 and C58 ECM connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:

      Terminals
      Condition
      Specified Condition
      A24-41 (CANH) - A29-49 (CANL)
      Ignition Switch off
      108 to 132 Ω



    3. C136709E12
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:

      Terminals
      Wiring Color
      Terminal Description
      Condition
      Specified Condition
      A24-41 (CANH) - A24-49 (CANL)
      B - W
      HIGH-level CAN bus wire - LOW-level CAN bus wire
      Ignition Switch off
      108 to 132 Ω
      A24-41 (CANH) - C58-81 (E1)
      B - W-B
      HIGH-level CAN bus wire - Ground
      Ignition Switch off
      200 Ω or higher
      A24-49 (CANL) - C58-81 (E1)
      W - W-B
      LOW-level CAN bus wire - Ground
      Ignition Switch off
      200 Ω or higher
      A24-41 (CANH) - A24-20 (BATT)
      B - Y
      HIGH-level CAN bus wire - Battery positive
      Cable disconnected from negative (-) battery terminal
      6 kΩ or higher
      A24-49 (CANL) - A24-20 (BATT)
      W - Y
      LOW-level CAN bus wire - Battery positive
      Cable disconnected from negative (-) battery terminal
      6 kΩ or higher



  3. 2GR-FE


    A107881E51


    1. Disconnect the A55 and C55 ECM connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:

      Terminals
      Condition
      Specified Condition
      A55-41 (CANH) - A55-49 (CANL)
      Ignition Switch off
      108 to 132 Ω



    3. C136709E13
    4. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:

      Terminals
      Wiring Color
      Terminal Description
      Condition
      Specified Condition
      A55-41 (CANH) - A55-49 (CANL)
      B - W
      HIGH-level CAN bus wire - LOW-level CAN bus wire
      Ignition Switch off
      108 to 132 Ω
      A55-41 (CANH) - A55-32 (EC)
      B - W-B
      HIGH-level CAN bus wire - Ground
      Ignition Switch off
      200 Ω or higher
      A55-49 (CANL) - A55-32 (EC)
      W - W-B
      LOW-level CAN bus wire - Ground
      Ignition Switch off
      200 Ω or higher
      A55-41 (CANH) - A55-20 (BATT)
      B - Y
      HIGH-level CAN bus wire - Battery positive
      Cable disconnected from negative (-) battery terminal
      6 kΩ or higher
      A55-49 (CANL) - A55-20 (BATT)
      W - Y
      LOW-level CAN bus wire - Battery positive
      Cable disconnected from negative (-) battery terminal
      6 kΩ or higher


AIR CONDITIONING AMPLIFIER


    E124470E20
  1. Check the harness side connector (E38) of the air conditioning amplifier.

    1. Disconnect the connector (E38) from the air conditioning amplifier.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:

      Terminals
      Wiring Color
      Terminal Description
      Condition
      Specified Condition
      E38-11 (CANH) - E38-12 (CANL)
      B - W
      HIGH-level CAN bus wire - LOW-level CAN bus wire
      Ignition Switch off
      54 to 69 Ω
      E38-11 (CANH) - E38-14 (GND)
      B - W-B
      HIGH-level CAN bus wire - Ground
      Ignition Switch off
      200 Ω or higher
      E38-12 (CANL) - E38-14 (GND)
      W - W-B
      LOW-level CAN bus wire - Ground
      Ignition Switch off
      200 Ω or higher
      E38-11 (CANH) - E38-21 (B)
      B - GR
      HIGH-level CAN bus wire - Battery positive
      Cable disconnected from negative (-) battery terminal
      6 kΩ or higher
      E38-12 (CANL) - E38-21 (B)
      W - GR
      LOW-level CAN bus wire - Battery positive
      Cable disconnected from negative (-) battery terminal
      6 kΩ or higher


COMBINATION METER


    C133254E01
  1. Disconnect the F1 combination meter connector.

  2. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminals
    Condition
    Specified Condition
    F1-17 (CANH) - F1-18 (CANL)
    Ignition Switch off
    108 to 132 Ω



  3. C133255E01
  4. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F1-17 (CANH) - F1-18 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Ignition Switch off
    108 to 132 Ω
    F1-17 (CANH) - F1-12 (E2)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    F1-18 (CANL) - F1-12 (E2)
    W - W-B
    LOW-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    F1-17 (CANH) - F1-2 (B2)
    B - R
    HIGH-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    F1-18 (CANL) - F1-2 (B2)
    W - R
    LOW-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


MAIN BODY ECU (INSTRUMENT PANEL J/B)


  1. Disconnect the E8 main body ECU connector.


    C142736E01

  2. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    CAN No.1 Bus Branch Wire 
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E8-5 (CANH) - E8-6 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Ignition Switch off
    54 to 69 Ω
    E8-5 (CANH) - E10-4 (CG)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    E8-6 (CANL) - E10-4 (CG)
    W - W-B
    LOW-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    E8-5 (CANH) - E10-16 (BAT)
    B - L
    HIGH-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    E8-6 (CANL) - E10-16 (BAT)
    W - L
    LOW-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher

    CAN MS Bus Main Wire 
    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E8-16 (CANP) - E8-15 (CANN)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Ignition Switch off
    108 to 132 Ω
    E8-16 (CANP) - E10-4 (CG)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    E8-15 (CANN) - E10-4 (CG)
    W - W-B
    LOW-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    E8-16 (CANP) - E10-16 (BAT)
    B - L
    HIGH-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    E8-15 (CANN) - E10-16 (BAT)
    W - L
    LOW-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


NAVIGATION ECU (w/ Navigation System)
  1. Disconnect the navigation receiver assembly connectors.



  2. Measure the resistance according to the value(s) in the table below.


    E178165E08


    Standard Resistance:

    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F26-2 (CANH) - F26-3 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Ignition Switch off
    54 to 69 Ω
    F26-2 (CANH) - F27-7 (GND)
    B - BR
    HIGH-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    F26-3 (CANL) - F27-7 (GND)
    W - BR
    LOW-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    F26-2 (CANH) - F27-4 (B)
    B - L-Y
    HIGH-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    F26-3 (CANL) - F27-4 (B)
    W - L-Y
    LOW-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


CERTIFICATION ECU (w/ Entry and Start System)


    C142198E05
  1. Disconnect the certification ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    E74-27 (CANH) - E74-28 (CANL)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Ignition Switch off
    108 to 132 Ω
    E74-27 (CANH) - E74-17 (E)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    E74-28 (CANL) - E74-17 (E)
    W - W-B
    LOW-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    E74-27 (CANH) - E74-1 (+B)
    B - W
    HIGH-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    E74-28 (CANL) - E74-1 (+B)
    W - W
    LOW-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher


CLEARANCE WARNING ECU (w/ TOYOTA Parking Assist-sensor System)


    C142212E04
  1. Disconnect the clearance warning ECU connector.

  2. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:

    Terminals
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    O28-3 (R1) - O28-5 (R2)
    B - W
    HIGH-level CAN bus wire - LOW-level CAN bus wire
    Ignition Switch off
    54 to 69 Ω
    O28-3 (R1) - O28-17 (E)
    B - W-B
    HIGH-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    O28-5 (R2) - O28-17 (E)
    W - W-B
    LOW-level CAN bus wire - Ground
    Ignition Switch off
    200 Ω or higher
    O28-3 (R1) - E10-16 (BAT)
    B - L
    HIGH-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher
    O28-5 (R2) - E10-16 (BAT)
    W - L
    LOW-level CAN bus wire - Battery positive
    Cable disconnected from negative (-) battery terminal
    6 kΩ or higher