HOOD LOCK CONTROL CABLE ASSEMBLY > REMOVAL |
| 1. REMOVE FRONT WHEEL |
| 2. REMOVE COOL AIR INTAKE DUCT SEAL (for 2GR-FE) |
![]() |
Remove the 7 clips and intake duct seal.
| 3. REMOVE FRONT BUMPER ASSEMBLY (w/o Headlight Cleaner System) |
![]() |
Put protective tape around the front bumper assembly.
![]() |
Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.
![]() |
Remove the 8 screws, 2 clips, 2 radiator grille protectors and bolt.
![]() |
Disengage the 2 claws and disconnect the front bumper assembly as shown in the illustration.
Disconnect 2 fog light connectors.
w/ TOYOTA Parking Assist-sensor System:
Disengage the clamp and disconnect the clearance sonar connector.
Remove the front bumper assembly.
| 4. REMOVE FRONT BUMPER ASSEMBLY (w/ Headlight Cleaner System) |
![]() |
Put protective tape around the front bumper assembly.
![]() |
Using a screwdriver, turn the pin 90 degrees and remove the pin hold clip.
![]() |
Remove the 8 screws, 2 clips, 2 radiator grille protectors and bolt.
![]() |
Disengage the 2 claws and disconnect the front bumper assembly as shown in the illustration.
Disconnect 2 fog light connectors.
w/ TOYOTA Parking Assist-sensor System:
Disengage the clamp and disconnect the clearance sonar connector.
![]() |
Disconnect the headlight cleaner washer hose, and then remove the front bumper assembly.
| 5. REMOVE FRONT FENDER LINER (w/o Front Fender Mudguard) |
![]() |
Remove the 5 clips and bolt.
Remove the 5 screws, grommet and the front fender liner.
| 6. REMOVE FRONT FENDER MUDGUARD SUB-ASSEMBLY (w/ Front Fender Mudguard) |
![]() |
Remove the 3 screws and front fender mudguard sub-assembly.
| 7. REMOVE FRONT FENDER LINER (w/ Front Fender Mudguard) |
![]() |
Remove the 4 clips and bolt.
Remove the 3 screws, grommet and the front fender liner.
| 8. REMOVE HIGH PITCHED HORN ASSEMBLY |
![]() |
Disconnect the connector.
Remove the bolt and the high pitched horn assembly.
| 9. REMOVE HOOD LOCK ASSEMBLY |
![]() |
Disconnect the connector.
Remove the 3 bolts.
![]() |
Disconnect the hood lock control cable.
Remove the hood lock assembly.
| 10. REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY (for LHD) |
![]() |
Disconnect the hood lock control cable and remove the hood lock control lever.
| 11. REMOVE HOOD LOCK CONTROL LEVER SUB-ASSEMBLY (for RHD) |
![]() |
Disconnect the hood lock control cable and remove the hood lock control lever.
| 12. REMOVE HOOD LOCK CONTROL CABLE ASSEMBLY (for LHD) |
Using a screwdriver, disconnect the clamps shown in the illustration.

| Area | Part Name | Area | Part Name |
| A | Hood lock control cable | H | Grommet |
| B | Clamp | I | Side member outer |
| C | Wire harness | J | Radiator |
| D | Pillar | K | Radiator support cover (for 2GR-FE) |
| E | Nut | L | Front fender apron |
| F | Radiator support upper | M | Brace |
| G | Hood lock protector | - | - |
Pull the cable from the engine compartment and remove it.
| 13. REMOVE HOOD LOCK CONTROL CABLE ASSEMBLY (for RHD) |
Using a screwdriver, disconnect the clamps shown in the illustration.

| Area | Part Name | Area | Part Name |
| A | Hood lock control cable | G | Side member outer |
| B | Clamp | H | Radiator |
| C | Washer hose | I | Radiator support cover (for 2GR-FE) |
| D | Radiator support upper | J | Front fender apron |
| E | Hood lock protector | K | Brace |
| F | Grommet | L | Pillar |
Pull the cable from the engine compartment and remove it.