ENGINE UNIT > DISASSEMBLY |
| 1. REMOVE OIL FILLER CAP SUB-ASSEMBLY |
![]() |
Remove the oil filler cap.
| 2. REMOVE OIL FILLER CAP GASKET |
![]() |
Remove the oil filler cap gasket.
| 3. REMOVE VENTILATION VALVE SUB-ASSEMBLY |
![]() |
Remove the ventilation valve.
| 4. REMOVE SPARK PLUG |
![]() |
Remove the spark plugs.
| 5. REMOVE OIL FILTER SUB-ASSEMBLY |
![]() |
Using SST, remove the oil filter.
| 6. REMOVE OIL COOLER ASSEMBLY |
![]() |
Remove the oil filter union, plate washer, nut, oil cooler and O-ring.
Remove the union bolt.
| 7. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY |
![]() |
Remove the 2 bolts and disconnect the 2 engine wires.
![]() |
Remove the 8 bolts, 2 nuts, and the cylinder head cover.
| 8. REMOVE CYLINDER HEAD COVER GASKET |
![]() |
Remove the cylinder head cover gasket.
| 9. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY |
Lift the engine upward using the chain block.
![]() |
Remove the bolt, nut and V-ribbed belt tensioner.
| 10. REMOVE CRANKSHAFT POSITION SENSOR |
![]() |
Remove the wire harness clamp.
Separate the wire harness from the wire harness clamp bracket.
![]() |
Remove the 2 bolts and sensor.
| 11. REMOVE CAMSHAFT POSITION SENSOR |
![]() |
Remove the bolt and sensor.
| 12. REMOVE CRANKSHAFT PULLEY |
![]() |
Using SST, fix the pulley in place and loosen the pulley bolt.
![]() |
Using SST, remove the pulley bolt and pulley.
| 13. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY |
![]() |
Disconnect the camshaft timing oil control valve assembly connector.
Remove the bolt and camshaft timing oil control valve assembly.
| 14. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY |
![]() |
Remove the 2 nuts, tensioner and gasket.
| 15. REMOVE WATER PUMP PULLEY |
![]() |
Using SST, remove the 4 bolts and water pump pulley.
| 16. REMOVE WATER PUMP ASSEMBLY |
![]() |
Remove the clamp of the crankshaft position sensor from the water pump.
Disconnect the wire of the crankshaft position sensor from the clamp bracket.
![]() |
Remove the 4 bolts, 2 nuts and clamp bracket.
![]() |
Using a screwdriver, pry between the water pump and cylinder block, and then remove the water pump.
| 17. REMOVE OIL PAN DRAIN PLUG |
![]() |
Remove the oil pan drain plug and gasket.
| 18. REMOVE OIL PAN SUB-ASSEMBLY |
![]() |
Remove the 12 bolts and 2 nuts.
![]() |
Insert the blade of oil pan seal cutter between the crankcase and oil pan. Cut through the sealer and remove the oil pan.
| 19. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY |
![]() |
Using a E10 "TORX" socket, remove the stud bolt for the drive belt tensioner from the cylinder block.
Remove the 12 bolts and 2 nuts.
![]() |
Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.
| 20. REMOVE TIMING CHAIN CASE OIL SEAL |
![]() |
Using a screwdriver and a hammer, remove the oil seal.
| 21. REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE |
![]() |
Remove the crankshaft position sensor plate.
| 22. REMOVE TIMING CHAIN GUIDE |
![]() |
Remove the bolt and timing chain guide.
| 23. REMOVE CHAIN TENSIONER SLIPPER |
![]() |
Remove the bolt and chain tensioner slipper.
| 24. REMOVE NO. 1 CHAIN VIBRATION DAMPER |
![]() |
Remove the 2 bolts and chain vibration damper.
| 25. REMOVE CHAIN SUB-ASSEMBLY |
![]() |
Remove the chain sub-assembly.
| 26. REMOVE CRANKSHAFT TIMING SPROCKET |
![]() |
Remove the crankshaft timing sprocket.
| 27. REMOVE NO. 2 CHAIN SUB-ASSEMBLY |
![]() |
Turn the crankshaft by 90° counterclockwise to align the adjusting hole of the oil pump drive shaft sprocket with the groove of the oil pump.
![]() |
Insert a 4 mm diameter bar into the adjusting hole of the oil pump drive shaft sprocket to lock the gear in position, and then remove the nut.
![]() |
Remove the bolt, chain tensioner plate and spring.
![]() |
Remove the chain tensioner, oil pump driven sprocket and chain.
| 28. REMOVE KEYS |
![]() |
Remove the 2 pulley set keys from the crankshaft.
| 29. REMOVE NO. 2 CAMSHAFT |
![]() |
Using several steps, uniformly loosen and remove the 10 bearing cap bolts in the sequence shown in the illustration.
Remove the 5 bearing caps.
| 30. REMOVE CAMSHAFT |
![]() |
Using several steps, uniformly loosen and remove the 10 bearing cap bolts in the sequence shown in the illustration.
Remove the 5 bearing caps.
| 31. REMOVE NO. 1 CAMSHAFT BEARING |
![]() |
| 32. REMOVE NO. 2 CAMSHAFT BEARING |
![]() |
Remove the No. 2 camshaft bearing.
| 33. REMOVE CAMSHAFT TIMING SPROCKET |
![]() |
Clamp the camshaft in a vise.
Remove the flange bolt of the camshaft timing sprocket.
| 34. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY |
![]() |
Clamp the camshaft in a vise, and make sure that the camshaft timing gear does not rotate.
Cover all the oil ports except the advance side port shown in the illustration with vinyl tape.
![]() |
Apply air pressure of 100 kPa (1.0 kgf/cm2, 14 psi) to the oil path, then turn the camshaft timing gear in the advance direction (counterclockwise) by hand.
![]() |
Remove the flange bolt of the camshaft timing gear.
| 35. REMOVE CYLINDER HEAD SUB-ASSEMBLY |
![]() |
Using several steps, uniformly loosen and remove the 10 cylinder head bolts and 10 plate washers with a 10 mm bi-hexagon wrench in the sequence shown in the illustration.
![]() |
Using a screwdriver with its tip wrapped with tape, pry between the cylinder head and cylinder block, and remove the cylinder head.
| 36. REMOVE CYLINDER HEAD GASKET |
![]() |
Remove the cylinder head gasket.
| 37. REMOVE CYLINDER BLOCK WATER JACKET SPACER |
![]() |
Using needle-nose pliers, remove the cylinder block water jacket spacer.
| 38. REMOVE OIL CONTROL VALVE FILTER |
![]() |
Using an 8 mm socket hexagon wrench, remove the plug and filter.
| 39. REMOVE OIL PUMP ASSEMBLY |
![]() |
Remove the 3 bolts, oil pump and gasket.
| 40. REMOVE NO. 1 AND NO. 2 BALANCESHAFT SUB-ASSEMBLY |
![]() |
Uniformly loosen and remove the 8 bolts in the sequence shown in the illustration.
![]() |
Remove the No. 1 and No. 2 balanceshafts.
| 41. REMOVE NO. 1 BALANCESHAFT BEARING |
![]() |
Remove the balanceshaft bearings.
| 42. REMOVE ENGINE REAR OIL SEAL |
![]() |
Using a knife, cut off the oil seal lip.
Using a screwdriver with its tip taped, pry out the oil seal.
| 43. REMOVE STIFFENING CRANKCASE ASSEMBLY |
![]() |
Uniformly loosen and remove the 11 bolts in the sequence shown in the illustration.
![]() |
Using a screwdriver, remove the crankcase by prying between the crankcase and cylinder block.
![]() |
Remove the O-ring from the cylinder block.
| 44. REMOVE PISTON SUB-ASSEMBLY WITH CONNECTING ROD |
![]() |
Using a ridge reamer, remove all the carbon from the top of the cylinder.
![]() |
Check that the matchmarks on the connecting rod and cap are aligned to ensure the correct reassembly.
![]() |
Using a 12 mm socket wrench, uniformly loosen the 2 bolts.
Using the 2 removed connecting rod cap bolts, remove the connecting rod cap and lower bearing by wiggling the connecting rod cap right and left.
Push the piston, connecting rod assembly and upper bearing through the top of the cylinder block.
| 45. REMOVE CONNECTING ROD BEARING |
Remove the connecting rod bearings.
| 46. REMOVE PISTON RING SET |
![]() |
Using a piston ring expander, remove the 2 compression rings.
Remove the oil ring rail and oil ring expander by hand.
| 47. REMOVE PISTON PIN HOLE SNAP RING |
![]() |
Using a screwdriver, pry out the 2 snap rings.
| 48. REMOVE PISTON |
![]() |
Gradually heat the piston to approximately 80 to 90°C (176 to 194°F).
![]() |
Using a plastic hammer and brass bar, lightly tap out the piston pin and remove the connecting rod.
| 49. REMOVE CRANKSHAFT |
![]() |
Uniformly loosen and remove the 10 main bearing cap bolts in the sequence shown in the illustration.
![]() |
Use 2 removed main bearing cap bolts to remove the 5 main bearing caps and 5 lower bearings.
Lift out the crankshaft.
| 50. REMOVE UPPER CRANKSHAFT THRUST WASHER |
![]() |
Remove the upper thrust washers from the cylinder block.
| 51. REMOVE CRANKSHAFT BEARING |
![]() |
Remove the 5 upper main bearings from the cylinder block.
| 52. REMOVE NO. 2 CRANKSHAFT BEARING |
![]() |
Remove the 5 lower main bearings from the 5 main bearing caps.
| 53. REMOVE STUD BOLT |
| 54. REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY |
![]() |
Using a 5 mm hexagon wrench, remove the bolts and oil nozzles.
| 55. CLEAN CYLINDER BLOCK |