Home › ENGINE ยท 2AZ-FE › ENGINE MECHANICAL › ENGINE UNIT

ENGINE UNIT > DISASSEMBLY

for Preparation Click here



1. REMOVE OIL FILLER CAP SUB-ASSEMBLY


    A128158
  1. Remove the oil filler cap.



2. REMOVE OIL FILLER CAP GASKET


    A128159
  1. Remove the oil filler cap gasket.



3. REMOVE VENTILATION VALVE SUB-ASSEMBLY


    A128160
  1. Remove the ventilation valve.



4. REMOVE SPARK PLUG


    A128161
  1. Remove the spark plugs.



5. REMOVE OIL FILTER SUB-ASSEMBLY


    A036541E01
  1. Using SST, remove the oil filter.

    SST
    09228-06501  

    HINT:
    Place a container for oil to be drained before removing the oil filter.



6. REMOVE OIL COOLER ASSEMBLY


    A135533
  1. Remove the oil filter union, plate washer, nut, oil cooler and O-ring.

  1. Remove the union bolt.



7. REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY


    A112210E01
  1. Remove the 2 bolts and disconnect the 2 engine wires.



    A127550E02
  1. Remove the 8 bolts, 2 nuts, and the cylinder head cover.



8. REMOVE CYLINDER HEAD COVER GASKET


    A144061
  1. Remove the cylinder head cover gasket.



9. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY
  1. Lift the engine upward using the chain block.

    NOTICE:
    Do not lift the engine more than necessary.



    A112212
  1. Remove the bolt, nut and V-ribbed belt tensioner.



10. REMOVE CRANKSHAFT POSITION SENSOR


    A094516E01
  1. Remove the wire harness clamp.

  1. Separate the wire harness from the wire harness clamp bracket.



    A063828
  1. Remove the 2 bolts and sensor.



11. REMOVE CAMSHAFT POSITION SENSOR


    A128164
  1. Remove the bolt and sensor.



12. REMOVE CRANKSHAFT PULLEY


    A013697E02
  1. Using SST, fix the pulley in place and loosen the pulley bolt.

    SST
    09213-54015   (91651-60855)
    09330-00021  



    A124860E01
  1. Using SST, remove the pulley bolt and pulley.

    SST
    09950-50013   (09951-05010, 09952-05010, 09953-05020, 09954-05021)
    09950-40011   (09957-04010)

    HINT:
    If necessary, remove the pulley and pulley bolt using SST.



13. REMOVE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY


    A124556
  1. Disconnect the camshaft timing oil control valve assembly connector.

  1. Remove the bolt and camshaft timing oil control valve assembly.



14. REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY


    A098348E01
  1. Remove the 2 nuts, tensioner and gasket.

    NOTICE:
    Do not turn the crankshaft without the chain tensioner.



15. REMOVE WATER PUMP PULLEY


A098715E03
  1. Using SST, remove the 4 bolts and water pump pulley.

    SST
    09960-10010   (09962-01000, 09963-00700)



16. REMOVE WATER PUMP ASSEMBLY


A094516E01
  1. Remove the clamp of the crankshaft position sensor from the water pump.

  1. Disconnect the wire of the crankshaft position sensor from the clamp bracket.



    B012052E03
  1. Remove the 4 bolts, 2 nuts and clamp bracket.



    A129792
  1. Using a screwdriver, pry between the water pump and cylinder block, and then remove the water pump.

    HINT:
    Tape the screwdriver tip before use.

    NOTICE:
    Be careful not to damage the contact surfaces of the water pump and cylinder block.



17. REMOVE OIL PAN DRAIN PLUG


    A128176
  1. Remove the oil pan drain plug and gasket.



18. REMOVE OIL PAN SUB-ASSEMBLY


    A114333
  1. Remove the 12 bolts and 2 nuts.



    A000019
  1. Insert the blade of oil pan seal cutter between the crankcase and oil pan. Cut through the sealer and remove the oil pan.

    NOTICE:
    Be careful not to damage the contact surfaces of the crankcase, chain cover and oil pan.



19. REMOVE TIMING CHAIN COVER SUB-ASSEMBLY


    A128178
  1. Using a E10 "TORX" socket, remove the stud bolt for the drive belt tensioner from the cylinder block.

  1. Remove the 12 bolts and 2 nuts.



    A128179
  1. Remove the timing chain cover by prying between the timing chain cover and cylinder head or cylinder block with a screwdriver.

    NOTICE:
    Be careful not to damage the contact surfaces of the timing chain cover, cylinder block and cylinder head.

    HINT:
    Tape the screwdriver tip before use.



20. REMOVE TIMING CHAIN CASE OIL SEAL


    A128180
  1. Using a screwdriver and a hammer, remove the oil seal.



21. REMOVE NO. 1 CRANKSHAFT POSITION SENSOR PLATE


    A132571
  1. Remove the crankshaft position sensor plate.



22. REMOVE TIMING CHAIN GUIDE


    A125373
  1. Remove the bolt and timing chain guide.



23. REMOVE CHAIN TENSIONER SLIPPER


    A125372
  1. Remove the bolt and chain tensioner slipper.



24. REMOVE NO. 1 CHAIN VIBRATION DAMPER


    A125371
  1. Remove the 2 bolts and chain vibration damper.



25. REMOVE CHAIN SUB-ASSEMBLY


    A128185
  1. Remove the chain sub-assembly.



26. REMOVE CRANKSHAFT TIMING SPROCKET


    A125374
  1. Remove the crankshaft timing sprocket.



27. REMOVE NO. 2 CHAIN SUB-ASSEMBLY


    A098351E01
  1. Turn the crankshaft by 90° counterclockwise to align the adjusting hole of the oil pump drive shaft sprocket with the groove of the oil pump.



    A098352E01
  1. Insert a 4 mm diameter bar into the adjusting hole of the oil pump drive shaft sprocket to lock the gear in position, and then remove the nut.



    B011415E03
  1. Remove the bolt, chain tensioner plate and spring.



    A063847
  1. Remove the chain tensioner, oil pump driven sprocket and chain.



28. REMOVE KEYS


    A131498
  1. Remove the 2 pulley set keys from the crankshaft.



29. REMOVE NO. 2 CAMSHAFT


    A098174E11
  1. Using several steps, uniformly loosen and remove the 10 bearing cap bolts in the sequence shown in the illustration.

  1. Remove the 5 bearing caps.



30. REMOVE CAMSHAFT


    A098175E04
  1. Using several steps, uniformly loosen and remove the 10 bearing cap bolts in the sequence shown in the illustration.

  1. Remove the 5 bearing caps.



31. REMOVE NO. 1 CAMSHAFT BEARING


A128191
Remove the No. 1 camshaft bearing.


32. REMOVE NO. 2 CAMSHAFT BEARING


    A032664
  1. Remove the No. 2 camshaft bearing.



33. REMOVE CAMSHAFT TIMING SPROCKET


    A032167
  1. Clamp the camshaft in a vise.

  1. Remove the flange bolt of the camshaft timing sprocket.



34. REMOVE CAMSHAFT TIMING GEAR ASSEMBLY


    A090848E03
  1. Clamp the camshaft in a vise, and make sure that the camshaft timing gear does not rotate.

  1. Cover all the oil ports except the advance side port shown in the illustration with vinyl tape.



    A031032
  1. Apply air pressure of 100 kPa (1.0 kgf/cm2, 14 psi) to the oil path, then turn the camshaft timing gear in the advance direction (counterclockwise) by hand.

    CAUTION:
    Cover the paths with a shop rag or piece of cloth to avoid oil splashes.

    HINT:
    Depending on the air pressure, the camshaft timing gear will turn to the advance angle side without applying force by hand. Also, if the pressure is difficult to apply because of air leakage from the port, the lock may be difficult to release.



    A032639
  1. Remove the flange bolt of the camshaft timing gear.

    NOTICE:
    1. Be sure not to remove the other 4 bolts.
    2. If planning to reuse the gear, be sure to release the straight pin lock before installing the gear.



35. REMOVE CYLINDER HEAD SUB-ASSEMBLY


    F050595E04
  1. Using several steps, uniformly loosen and remove the 10 cylinder head bolts and 10 plate washers with a 10 mm bi-hexagon wrench in the sequence shown in the illustration.

    NOTICE:
    Head warpage or cracking could result from removing the bolts in the wrong order.



    A126930
  1. Using a screwdriver with its tip wrapped with tape, pry between the cylinder head and cylinder block, and remove the cylinder head.

    NOTICE:
    Be careful not to damage the contact surfaces of the cylinder head and cylinder block.



36. REMOVE CYLINDER HEAD GASKET


    A126929
  1. Remove the cylinder head gasket.



37. REMOVE CYLINDER BLOCK WATER JACKET SPACER


    A128208
  1. Using needle-nose pliers, remove the cylinder block water jacket spacer.

    NOTICE:
    Be sure to remove the water jacket spacer if turning the cylinder block upside down.



38. REMOVE OIL CONTROL VALVE FILTER


    A128210
  1. Using an 8 mm socket hexagon wrench, remove the plug and filter.



39. REMOVE OIL PUMP ASSEMBLY


    A128253
  1. Remove the 3 bolts, oil pump and gasket.



40. REMOVE NO. 1 AND NO. 2 BALANCESHAFT SUB-ASSEMBLY


    A128197E01
  1. Uniformly loosen and remove the 8 bolts in the sequence shown in the illustration.



    A128203E02
  1. Remove the No. 1 and No. 2 balanceshafts.



41. REMOVE NO. 1 BALANCESHAFT BEARING


    A128204E02
  1. Remove the balanceshaft bearings.



42. REMOVE ENGINE REAR OIL SEAL


    A128201E01
  1. Using a knife, cut off the oil seal lip.

  1. Using a screwdriver with its tip taped, pry out the oil seal.

    NOTICE:
    After removing the oil seal, check the crankshaft for damage. If it is damaged, smooth the surface with 400-grit sandpaper.



43. REMOVE STIFFENING CRANKCASE ASSEMBLY


    A128202E02
  1. Uniformly loosen and remove the 11 bolts in the sequence shown in the illustration.



    A128205E01
  1. Using a screwdriver, remove the crankcase by prying between the crankcase and cylinder block.

    NOTICE:
    Be careful not to damage the contact surfaces of the crankcase and cylinder block.



    A128206
  1. Remove the O-ring from the cylinder block.



44. REMOVE PISTON SUB-ASSEMBLY WITH CONNECTING ROD


    A013469
  1. Using a ridge reamer, remove all the carbon from the top of the cylinder.



    A063893E01
  1. Check that the matchmarks on the connecting rod and cap are aligned to ensure the correct reassembly.

    HINT:
    The matchmarks on the connecting rods and caps are provided for ensuring the correct reassembly.



    A013397
  1. Using a 12 mm socket wrench, uniformly loosen the 2 bolts.

  1. Using the 2 removed connecting rod cap bolts, remove the connecting rod cap and lower bearing by wiggling the connecting rod cap right and left.

    HINT:
    Keep the lower bearing inserted in the connecting rod cap.

  1. Push the piston, connecting rod assembly and upper bearing through the top of the cylinder block.

    HINT:
    1. Keep the bearing, connecting rod and cap together.
    2. Arrange the piston and connecting rod assemblies in the correct order.



45. REMOVE CONNECTING ROD BEARING
  1. Remove the connecting rod bearings.

    HINT:
    Arrange the removed parts in the correct order.



46. REMOVE PISTON RING SET


    A128232E01
  1. Using a piston ring expander, remove the 2 compression rings.

  1. Remove the oil ring rail and oil ring expander by hand.

    HINT:
    Arrange the removed parts in the correct order.



47. REMOVE PISTON PIN HOLE SNAP RING


    A128233
  1. Using a screwdriver, pry out the 2 snap rings.



48. REMOVE PISTON


    A109729
  1. Gradually heat the piston to approximately 80 to 90°C (176 to 194°F).



    A106279
  1. Using a plastic hammer and brass bar, lightly tap out the piston pin and remove the connecting rod.

    HINT:
    1. The piston and pin are a matched set.
    2. Arrange the pistons, pins, rings, connecting rods and bearings in the correct order.



49. REMOVE CRANKSHAFT


    A128235E01
  1. Uniformly loosen and remove the 10 main bearing cap bolts in the sequence shown in the illustration.



    A087781
  1. Use 2 removed main bearing cap bolts to remove the 5 main bearing caps and 5 lower bearings.

    NOTICE:
    Insert the bolts into one of the caps. Ease the cap out by gently pulling up and applying force toward the front and back side of the cylinder block, as shown in the illustration. Take care not to damage the contact surfaces of the cap and cylinder block.

    HINT:
    1. Keep the lower bearing and main bearing cap together.
    2. Arrange the main bearing caps in the correct order.

  1. Lift out the crankshaft.



50. REMOVE UPPER CRANKSHAFT THRUST WASHER


    A013501
  1. Remove the upper thrust washers from the cylinder block.



51. REMOVE CRANKSHAFT BEARING


    A063901
  1. Remove the 5 upper main bearings from the cylinder block.

    HINT:
    Arrange the bearings in the correct order.



52. REMOVE NO. 2 CRANKSHAFT BEARING


    A063902
  1. Remove the 5 lower main bearings from the 5 main bearing caps.

    HINT:
    Arrange the bearings in the correct order.



53. REMOVE STUD BOLT


54. REMOVE NO. 1 OIL NOZZLE SUB-ASSEMBLY


    A128251E01
  1. Using a 5 mm hexagon wrench, remove the bolts and oil nozzles.



55. CLEAN CYLINDER BLOCK

NOTICE:
If the cylinder is washed at high temperatures, the cylinder liner will stick out beyond the cylinder block. Always wash the cylinder block at a temperature of 45°C (113°F) or less.