ENGINE UNIT > REASSEMBLY |
| 1. INSTALL RING PIN |
Using a plastic hammer, tap into the ring pin.

| Item | Protrusion |
| Pin A | 6 mm (0.236 in.) |
| Pin B | 5 mm (0.197 in.) |
| 2. INSTALL STUD BOLT |
Install the stud bolts as shown in the illustration.

| 3. INSTALL STRAIGHT PIN |
Using a plastic hammer, tap into the straight pin.

| Item | Protrusion |
| Pin A | 8 mm (0.315 in.) |
| Pin B | 7.5 mm (0.295 in.) |
| Pin C | 12 mm (0.472 in.) |
| Pin D | 5 mm (0.197 in.) |
| 4. INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY |
![]() |
Using a 5 mm hexagon wrench, install the oil nozzles with the bolts.
| 5. INSTALL PISTON |
![]() |
Using a screwdriver, install a new snap ring at one end of the piston pin hole.
Gradually heat the piston to approximately 80 to 90°C (176 to 194°F).
![]() |
Align the front marks of the piston and connecting rod, and push in the piston with your thumb.
Using a screwdriver, install a new snap ring on the other end of the piston pin hole.
![]() |
Check the fitting condition between the piston and piston pin by trying to move the piston back and forth on the piston pin.
| 6. INSTALL PISTON RING SET |
![]() |
Install the oil ring expander and oil ring rail by hand.
![]() |
Using a piston ring expander, install the 2 compression rings so that the paint marks are positioned as shown in the illustration.
![]() |
Position the piston rings so that the ring ends are as shown in the illustration.
| 7. INSTALL CRANKSHAFT BEARING |
![]() |
Install the upper bearing with an oil groove on the cylinder block.
| 8. INSTALL NO. 2 CRANKSHAFT BEARING |
![]() |
Install the lower bearing on the bearing cap.
| 9. INSTALL UPPER CRANKSHAFT THRUST WASHER |
![]() |
Install the 2 thrust washers under the No. 3 journal of the cylinder block with the oil grooves facing outward.
Apply engine oil to the crankshaft thrust washer.
| 10. INSTALL CRANKSHAFT |
Apply engine oil to the upper bearing and install the crankshaft on the cylinder block.
Apply engine oil to the lower bearing.
![]() |
Examine the front marks and install the bearing caps on the cylinder block.
Apply a light coat of engine oil to the threads and under the bearing cap bolts.
Install the crankshaft bearing cap bolts.
Step 1
![]() |
Install and uniformly tighten the 10 main bearing cap bolts in the sequence shown in the illustration.
![]() |
Retighten the 10 main bearing cap bolts in the sequence shown in the illustration.
Step 2
![]() |
Mark the front of the bearing cap bolts with paint.
Retighten the bearing cap bolts by 90°in the numerical order shown in the illustration.
Check that the paint mark is now at a 90°angle to the front.
Check that the crankshaft turns smoothly.
Check the crankshaft thrust clearance .
| 11. INSTALL CONNECTING ROD BEARING |
![]() |
Align the bearing claw with the groove of the connecting rod or connecting cap.
| 12. INSTALL PISTON SUB-ASSEMBLY WITH CONNECTING ROD |
Apply engine oil to the cylinder walls, the pistons, and the surfaces of connecting rod bearings.
![]() |
Check the position of the piston ring ends.
![]() |
Using a piston ring compressor, push the correctly numbered piston and connecting rod assemblies into each cylinder with the front mark of the piston facing forward.
![]() |
Check that the protrusion of the connecting rod cap is facing in the correct direction.
Apply a light coat of engine oil to the threads and under the heads of the connecting rod cap bolts.
Install the connecting cap bolts.
Step 1
![]() |
Install and alternately tighten the bolts of the connecting rod cap in several steps.
Step 2
![]() |
Mark the front of the connecting rod cap bolts with paint.
Retighten the cap bolts by 90°as shown in the illustration.
Check that the crankshaft turns smoothly.
Check the connecting rod thrust clearance .
| 13. INSTALL NO. 1 BALANCESHAFT BEARING |
![]() |
Install the bearings in the crankcase and balanceshaft housing.
Apply a light coat of engine oil to the bearings.
| 14. INSTALL NO. 1 AND NO. 2 BALANCESHAFT SUB-ASSEMBLY |
![]() |
Rotate the driven gear No. 1 of balanceshaft No. 1 in the rotating direction until it hits the stopper.
![]() |
Align the timing marks of the No. 1 and No. 2 balanceshafts as shown in the illustration.
![]() |
Place the No. 1 and No. 2 balanceshafts on the crankcase.
Apply a light coat of engine oil under the heads of the balanceshaft housing bolts.
Install the balanceshaft housing bolts.
Step 1
![]() |
Install and uniformly tighten the 8 bolts in the sequence shown in the illustration.
Step 2
![]() |
Mark the front side of each balanceshaft housing bolt head with paint.
Retighten the bolts by 90°as shown in the illustration.
Check that the paint marks are now at a 90°angle to the front.
| 15. INSTALL STIFFENING CRANKCASE ASSEMBLY |
![]() |
Place a new O-ring on the cylinder block, as shown in the illustration.
Temporarily tighten the pulley set bolt.
![]() |
Turn the crankshaft to set the crank pins of the No. 1 and No. 4 cylinders to the bottom.
![]() |
Apply seal packing in a continuous bead (diameter: 2.5 to 3.0 mm (0.098 to 0.118 in.)) to the places shown in the illustration.
![]() |
Install the stiffening crankcase so that the reference holes on the balanceshafts are positioned as shown in the illustration.
![]() |
Temporarily install the crankcase with the 11 bolts.
| Item | Length |
| Bolt A | 122 mm (4.803 in.) |
| Bolt B | 45 mm (1.772 in.) |
![]() |
Uniformly tighten the 11 bolts in the sequence shown in the illustration.
Wipe off the excess seal packing with a clean piece of cloth.
![]() |
Turn the crankshaft again to set the key groove to the bottom. Make sure that the timing marks are aligned as shown in the illustration.
Remove the pulley set bolt.
| 16. INSTALL OIL PUMP ASSEMBLY |
![]() |
Install a new gasket and oil pump with the 3 bolts.
| 17. INSTALL ENGINE REAR OIL SEAL |
![]() |
Using SST and a hammer, evenly tap the oil seal until its surface is flush with the rear oil seal retainer edge.
Apply MP grease to a new oil seal lip.
| 18. INSTALL OIL CONTROL VALVE FILTER |
Check that no foreign matter is on the mesh part of the filter.
![]() |
Using an 8 mm socket hexagon wrench, install a new gasket and the oil control valve filter with the screw plug.
| 19. INSTALL CYLINDER BLOCK WATER JACKET SPACER |
![]() |
Install the water jacket spacer as shown in the illustration.
| 20. INSTALL CYLINDER HEAD GASKET |
![]() |
Place a new gasket on the cylinder block surface with the Lot No. stamp facing upward.
| 21. INSTALL CYLINDER HEAD SUB-ASSEMBLY |
Apply a light coat of engine oil to the bolt threads and the area beneath the bolt heads that come in contact with the washers.
Install the bolts and plate washers to the cylinder head.
![]() |
Using several steps, uniformly install and tighten the 10 cylinder head set bolts and plate washers with a 10 mm bi-hexagon wrench in the order shown in the illustration.
![]() |
Mark the front side of the cylinder head bolt with paint.
Retighten the cylinder head bolts 90° in the sequence shown in the illustration.
Check that the paint mark is now at a 90° angle to the front.
| 22. INSTALL CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY |
![]() |
Apply a light coat of engine oil to a new O-ring, then install it onto the camshaft timing oil control valve.
![]() |
Install the camshaft timing oil control valve with the bolt.
| 23. INSTALL CAMSHAFT TIMING GEAR ASSEMBLY |
![]() |
Put the camshaft timing gear and camshaft together with the straight pin and key groove misaligned, as shown in the illustration.
Turn the camshaft timing gear as shown in the illustration while pushing it gently against the camshaft. Push further at the position where the pin fits into the groove.
Check that there is no clearance between the gear and camshaft.
Tighten the flange bolt with the camshaft timing gear fixed in place.
Check that the camshaft timing gear can move to the retard angle side (the right direction) and is locked in the most retarded position.
| 24. INSTALL CAMSHAFT TIMING SPROCKET |
![]() |
Clamp the camshaft in a vise.
Tighten the flange bolt with the camshaft timing sprocket fixed.
| 25. INSTALL NO. 1 CAMSHAFT BEARING |
![]() |
Install the No. 1 camshaft bearing.
| 26. INSTALL NO. 2 CAMSHAFT BEARING |
![]() |
Install the No. 2 camshaft bearing.
| 27. INSTALL CAMSHAFT |
Apply a light coat of engine oil to the journal portion of the camshaft.
![]() |
Examine the front marks and numbers, and check that the order is as shown in the illustration. Then install the bearing caps into the cylinder head.
Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.
![]() |
Using several steps, uniformly tighten the 10 bearing cap bolts in the sequence shown in the illustration.
| 28. INSTALL NO. 2 CAMSHAFT |
Apply a light coat of engine oil to the journal portion of the No. 2 camshaft.
![]() |
Examine the front marks and numbers, and check that the order is as shown in the illustration. Then install the bearing caps onto the cylinder head.
Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.
![]() |
Using several steps, uniformly tighten the 10 bearing cap bolts in the sequence shown in the illustration.
| 29. INSTALL KEYS |
![]() |
Install the 2 keys.
| 30. INSTALL NO. 2 CHAIN SUB-ASSEMBLY |
![]() |
Set the crankshaft key into the left horizontal position.
Turn the drive shaft so that the cutout faces upward.
![]() |
Align the yellow mark links with the timing marks of each gear as shown in the illustration.
Install the sprockets onto the crankshaft and oil pump shaft with the chain wrapped on the gears.
Temporarily tighten the oil pump drive shaft sprocket with the nut.
![]() |
Insert the damper spring into the adjusting hole, and then install the chain tensioner plate with the bolt.
![]() |
Align the adjusting hole of the oil pump drive shaft sprocket with the groove of the oil pump.
Insert a 4 mm diameter bar into the adjusting hole of the oil pump drive shaft gear to lock the gear in position, and then tighten the nut.
![]() |
Rotate the crankshaft clockwise by 90°, and align the crankshaft key to the top.
| 31. INSTALL CRANKSHAFT TIMING SPROCKET |
![]() |
Install the crankshaft timing sprocket.
| 32. INSTALL NO. 1 CHAIN VIBRATION DAMPER |
![]() |
Install the chain vibration damper with the 2 bolts.
| 33. INSTALL CHAIN SUB-ASSEMBLY |
![]() |
Set the No. 1 cylinder to TDC/compression.
Turn the camshafts with a wrench (using the hexagonal lobe) to align the timing marks of the camshaft timing gear with each timing mark located on the No. 1 and No. 2 bearing caps as shown in the illustration.
![]() |
Using the crankshaft pulley bolt, turn the crankshaft to position with the key on the crankshaft upward.
![]() |
Install the chain onto the crankshaft timing sprocket with the gold or pink mark link aligned with the timing mark on the crankshaft.
![]() |
Using SST and a hammer, tap in the crankshaft timing sprocket.
![]() |
Align the gold or yellow link with each timing mark located on the camshaft timing gear and sprocket, then install the chain.
| 34. INSTALL CHAIN TENSIONER SLIPPER |
![]() |
Install the chain tensioner slipper with the bolt.
| 35. INSTALL TIMING CHAIN GUIDE |
![]() |
Install the timing chain guide with the bolt.
| 36. INSTALL NO. 1 CRANKSHAFT POSITION SENSOR PLATE |
![]() |
Install the sensor plate with the "F" mark facing forward.
| 37. INSTALL TIMING CHAIN CASE OIL SEAL |
![]() |
Using SST, tap in a new oil seal until its surface is flush with the timing chain cover edge.
Apply a light coat of MP grease to the lip of the oil seal.
| 38. INSTALL TIMING CHAIN COVER SUB-ASSEMBLY |
Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the timing chain cover, cylinder head and cylinder block.
![]() |
Apply seal packing (diameter: 4.0 to 4.5 mm (0.157 to 0.177 in.)) as shown in the illustration.
Apply seal packing in a continuous bead as shown in the illustration.

![]() |
Install the timing chain cover with the 12 bolts and 2 nuts.
| Item | Length |
| Bolt A | 30 mm (1.18 in.) length for 10 mm head |
| Bolt B | 30 mm (1.18 in.) length for 12 mm head |
| Bolt C | 40 mm (1.57 in.) length for 14 mm head |
Using a E10 "torx" socket, install the stud bolt to the drive belt tensioner.
| 39. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY |
![]() |
Install the V-ribbed belt tensioner with the bolt and nut.
| 40. INSTALL OIL PAN SUB-ASSEMBLY |
![]() |
Remove any old packing material and be careful not to drop any oil on the contact surfaces of the cylinder block and oil pan.
Apply a continuous bead of seal packing (Diameter 3.0 to 4.0 mm (0.118 to 0.157 in.)) as shown in the illustration.
Install the oil pan to the cylinder block.
![]() |
Uniformly tighten the 12 bolts and 2 nuts in the sequence shown in the illustration.
| 41. INSTALL OIL PAN DRAIN PLUG |
![]() |
Install a new gasket and oil pan drain plug with a new gasket.
| 42. INSTALL WATER PUMP ASSEMBLY |
Remove any old seal packing material from the contact surface.
![]() |
Apply a continuous line of seal packing as shown in the illustration.
![]() |
Install the water pump and clamp bracket with the 4 bolts and 2 nuts.
![]() |
Install the wire of the crankshaft position sensor onto the clamp bracket.
Install the clamp of the crankshaft position sensor onto the water pump.
| 43. INSTALL WATER PUMP PULLEY |
![]() |
Using SST, install the water pump pulley with the 4 bolts.
| 44. INSTALL CRANKSHAFT POSITION SENSOR |
![]() |
Apply a light coat of engine oil to the O-ring of the sensor.
![]() |
Confirm that the wire harness of the sensor is placed as shown in the illustration.
![]() |
Install the sensor with the 2 bolts.
![]() |
Install the clamp of the crankshaft position sensor onto the water pump.
| 45. INSTALL CRANKSHAFT PULLEY |
Align the pulley set key with the key groove of the pulley.
![]() |
Using SST, fix the pulley in place and tighten the bolt.
| 46. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY |
![]() |
Release the ratchet pawl, then fully push in the plunger and hook the hook to the pin so that the plunger is in the position shown in the illustration.
![]() |
Install a new gasket and the chain tensioner with the 2 nuts.
![]() |
Turn the crankshaft counterclockwise, then disconnect the plunger knock pin from the hook.
![]() |
Turn the crankshaft clockwise, then check that the plunger is extended.
| 47. INSPECT VALVE CLEARANCE |
![]() |
Check only the valves indicated.
Using a feeler gauge, measure the clearance between the valve lifter and camshaft.
| Item | Standard Condition |
| Intake | 0.19 to 0.29 mm (0.0075 to 0.0114 in.) |
| Exhaust | 0.38 to 0.48 mm (0.0150 to 0.0189 in.) |
Record any out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve clearance lifters.
Turn the crankshaft 1 revolution (360°) and set the No. 4 cylinder to the TDC/compression.
![]() |
Check only the valves indicated.
Using a feeler gauge, measure the clearance between the valve lifter and camshaft.
| Item | Standard Condition |
| Intake | 0.19 to 0.29 mm (0.0075 to 0.0114 in.) |
| Exhaust | 0.38 to 0.48 mm (0.0150 to 0.0189 in.) |
Record any out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve lifters.
| 48. ADJUST VALVE CLEARANCE |
Remove the No. 2 camshaft (Click here).
Remove the camshaft (Click here).
Remove the valve lifters.
![]() |
Using a micrometer, measure the thickness of the removed valve lifters.
Calculate the thickness of a new lifter so that the valve clearance comes within the specified values.
| Item | Specification |
| Intake | A = B + (C - 0.24 mm (0.0095 in.)) |
| Exhaust | A = B + (C - 0.43 mm (0.0169 in.)) |
| A | New lifter thickness |
| B | Used lifter thickness |
| C | Measured valve clearance |
![]() |
Select a new lifter with a thickness as close as possible to the calculated values.
Valve lifter selection chart (intake).

| Lifter No. | Thickness mm (in.) | Lifter No. | Thickness mm (in.) | Lifter No. | Thickness mm (in.) |
| 06 | 5.060 (0.1992) | 30 | 5.300 (0.2087) | 54 | 5.540 (0.2181) |
| 08 | 5.080 (0.2000) | 32 | 5.320 (0.2094) | 56 | 5.560 (0.2189) |
| 10 | 5.100 (0.2008) | 34 | 5.340 (0.2102) | 58 | 5.580 (0.2197) |
| 12 | 5.120 (0.2016) | 36 | 5.360 (0.2110) | 60 | 5.600 (0.2205) |
| 14 | 5.140 (0.2024) | 38 | 5.380 (0.2118) | 62 | 5.620 (0.2213) |
| 16 | 5.160 (0.2031) | 40 | 5.400 (0.2126) | 64 | 5.640 (0.2220) |
| 18 | 5.180 (0.2039) | 42 | 5.420 (0.2134) | 66 | 5.660 (0.2228) |
| 20 | 5.200 (0.2047) | 44 | 5.440 (0.2142) | 68 | 5.680 (0.2236) |
| 22 | 5.220 (0.2055) | 46 | 5.460 (0.2150) | 70 | 5.700 (0.2244) |
| 24 | 5.240 (0.2063) | 48 | 5.480 (0.2157) | 72 | 5.720 (0.2252) |
| 26 | 5.260 (0.2071) | 50 | 5.500 (0.2165) | 74 | 5.740 (0.2260) |
| 28 | 5.280 (0.2079) | 52 | 5.520 (0.2173) | - | - |
Valve lifter selection chart (exhaust).

| Lifter No. | Thickness mm (in.) | Lifter No. | Thickness mm (in.) | Lifter No. | Thickness mm (in.) |
| 06 | 5.060 (0.1992) | 30 | 5.300 (0.2087) | 54 | 5.540 (0.2181) |
| 08 | 5.080 (0.2000) | 32 | 5.320 (0.2094) | 56 | 5.560 (0.2189) |
| 10 | 5.100 (0.2008) | 34 | 5.340 (0.2102) | 58 | 5.580 (0.2197) |
| 12 | 5.120 (0.2016) | 36 | 5.360 (0.2110) | 60 | 5.600 (0.2205) |
| 14 | 5.140 (0.2024) | 38 | 5.380 (0.2118) | 62 | 5.620 (0.2213) |
| 16 | 5.160 (0.2031) | 40 | 5.400 (0.2126) | 64 | 5.640 (0.2220) |
| 18 | 5.180 (0.2039) | 42 | 5.420 (0.2134) | 66 | 5.660 (0.2228) |
| 20 | 5.200 (0.2047) | 44 | 5.440 (0.2142) | 68 | 5.680 (0.2236) |
| 22 | 5.220 (0.2055) | 46 | 5.460 (0.2150) | 70 | 5.700 (0.2244) |
| 24 | 5.240 (0.2063) | 48 | 5.480 (0.2157) | 72 | 5.720 (0.2252) |
| 26 | 5.260 (0.2071) | 50 | 5.500 (0.2165) | 74 | 5.740 (0.2260) |
| 28 | 5.280 (0.2079) | 52 | 5.520 (0.2173) | - | - |
Install the selected valve lifter.
| 49. INSTALL CAMSHAFT POSITION SENSOR |
![]() |
Apply a light coat of engine oil to the O-ring of the sensor.
![]() |
Install the sensor with the bolt.
| 50. INSTALL CYLINDER HEAD COVER GASKET |
![]() |
Install the gasket to the cylinder head cover.
| 51. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY |
Remove any old packing material from the contact surface.
![]() |
Apply seal packing to the 2 locations shown in the illustration.
![]() |
Install the cylinder head cover with the 8 bolts and 2 nuts.
![]() |
Install the 2 engine wires with the 2 bolts.
| 52. INSTALL OIL COOLER ASSEMBLY |
Clean the oil cooler contact surface on the cooler mounting.
![]() |
Install a new O-ring to the oil cooler.
Apply a light coat of engine oil to the threads and under the head of the union bolt.
![]() |
Install the oil cooler with the plate washer, oil filter union and nut.
Apply adhesive to the threads of the oil filter union.
![]() |
Install the union bolt.
| 53. INSTALL OIL FILTER SUB-ASSEMBLY |
Check and clean the oil filter installation surface.
Apply clean engine oil to the gasket of a new oil filter.
Lightly screw the oil filter into place, and tighten it until the gasket contacts the seat.
When using a torque wrench:
![]() |
Using SST, tighten the oil filter.
When not using a torque wrench:
![]() |
Using SST, tighten it an additional 3/4 turn.
| 54. INSTALL SPARK PLUG |
![]() |
Install the spark plugs.
| 55. INSTALL VENTILATION VALVE SUB-ASSEMBLY |
![]() |
Apply adhesive to the threads of the ventilation valve.
![]() |
Install the ventilation valve.
| 56. INSTALL OIL FILLER CAP GASKET |
![]() |
Install the gasket to the cap.
| 57. INSTALL OIL FILLER CAP SUB-ASSEMBLY |
![]() |
Install the oil filler cap.