CAMSHAFT > INSTALLATION |
| 1. INSTALL CAMSHAFT TIMING GEAR ASSEMBLY |
![]() |
Put the camshaft timing gear and camshaft together with the straight pin and key groove misaligned, as shown in the illustration.
Turn the camshaft timing gear as shown in the illustration while pushing it gently against the camshaft. Push further at the position where the pin fits into the groove.
Check that there is no clearance between the gear and camshaft.
Tighten the flange bolt with the camshaft timing gear fixed in place.
Check that the camshaft timing gear can move to the retard angle side (the right direction) and is locked in the most retarded position.
| 2. INSTALL CAMSHAFT |
Apply a light coat of engine oil to the journal portion of the camshaft.
![]() |
Install the timing chain onto the camshaft timing gear with the paint mark aligned with the timing mark in the camshaft timing gear as shown in the illustration.
![]() |
Examine the front marks and numbers, and check that the order is as shown in the illustration. Then install the bearing caps into the cylinder head.
Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.
![]() |
Using several steps, uniformly tighten the 10 bearing cap bolts in the sequence shown in the illustration.
| 3. INSTALL NO. 2 CAMSHAFT |
Apply a light coat of engine oil to the journal portion of the No. 2 camshaft.
![]() |
Put the No. 2 camshaft on the cylinder head with the paint mark of the chain aligned with the timing mark on the camshaft timing sprocket.
![]() |
While holding the No. 2 camshaft by hand, temporarily tighten the camshaft timing sprocket set bolt.
![]() |
Examine the front marks and numbers, and check that the order is as shown in the illustration. Then install the bearing caps onto the cylinder head.
Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.
![]() |
Using several steps, uniformly tighten the 10 bearing cap bolts in the sequence shown in the illustration.
![]() |
While holding the camshaft with a wrench, tighten the camshaft timing sprocket set bolt.
![]() |
Check that the paint marks on the chain are aligned with the timing marks on the camshaft timing gear and camshaft timing sprocket. Also, check that the crankshaft pulley groove is aligned with the timing mark "0" of the timing chain cover.
| 4. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY |
![]() |
Release the ratchet pawl, then fully push in the plunger and hook the hook to the pin so that the plunger is in the position shown in the illustration.
![]() |
Install a new gasket and the chain tensioner with the 2 nuts.
![]() |
Turn the crankshaft counterclockwise, then disconnect the plunger knock pin from the hook.
![]() |
Turn the crankshaft clockwise, then check that the plunger is extended.
| 5. CHECK VALVE CLEARANCE |
![]() |
Check only the valves indicated.
Using a feeler gauge, measure the clearance between the valve lifter and camshaft.
| Item | Standard Condition |
| Intake | 0.19 to 0.29 mm (0.0075 to 0.0114 in.) |
| Exhaust | 0.38 to 0.48 mm (0.0150 to 0.0189 in.) |
Record any out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve clearance lifters.
Turn the crankshaft 1 revolution (360°) and set the No. 4 cylinder to the TDC/compression.
![]() |
Check only the valves indicated.
Using a feeler gauge, measure the clearance between the valve lifter and camshaft.
| Item | Standard Condition |
| Intake | 0.19 to 0.29 mm (0.0075 to 0.0114 in.) |
| Exhaust | 0.38 to 0.48 mm (0.0150 to 0.0189 in.) |
Record any out-of-specification valve clearance measurements. They will be used later to determine the required replacement valve lifters.
| 6. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY |
Remove any old packing material from the contact surface.
![]() |
Apply seal packing to the 2 locations shown in the illustration.
![]() |
Install the cylinder head cover with the 8 bolts and 2 nuts.
![]() |
Install the 2 engine wires with the 2 bolts.
| 7. INSTALL IGNITION COIL ASSEMBLY |
Install the 4 ignition coils with the 4 bolts.
| 8. INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY |
![]() |
Install the engine cover with the 2 nuts.
| 9. INSTALL FRONT FENDER APRON SEAL RH |
| 10. INSTALL ENGINE UNDER COVER LH |
| 11. INSTALL ENGINE UNDER COVER RH |
| 12. INSTALL FRONT WHEEL RH |
| 13. CHECK FOR ENGINE OIL LEAKS |