Home › STEERING › STEERING COLUMN › STEERING LOCK SYSTEM

DTC    B2788    IG2 Signal Malfunction

for Preparation Click here


DESCRIPTION

The steering lock ECU (steering lock actuator assembly) receives power from the IG2 relay. When the digital signal from the certification ECU (smart key ECU assembly) and the voltage from the IG2 relay are received by the steering lock ECU (steering lock actuator assembly), the steering will be unlocked. The steering lock ECU (steering lock actuator assembly) will not lock the steering wheel when power from the IG2 relay is present (this prevents the steering wheel from being locked while the vehicle is moving).

DTC No.
DTC Detection Condition
Trouble Area
B2788
Different information is obtained from IG2 signals received directly from the IG2 circuit, and from IG2 signals sent via LIN communication for 1 second.
  1. IG2 relay
  2. Harness or connector
  3. Main body ECU
  4. Steering lock ECU (Steering lock actuator assembly)

WIRING DIAGRAM


C113505E06


INSPECTION PROCEDURE

NOTICE:
  1. If the steering lock ECU (steering lock actuator assembly) is replaced, with the engine switch off and the shift lever in P, open and close the driver door to record the current lock position into the steering lock ECU (steering lock actuator assembly). If this is not performed, the engine may not start.
  2. After replacing the steering lock ECU (steering lock actuator assembly), perform the key ID code registration.

HINT:
When the engine switch is off, the main body ECU may occasionally go into a non-active state called sleep mode. Therefore, before proceeding with the inspection, it is necessary to perform the following steps to wake up the ECU:
With the engine switch off, open the driver door. Then (with the engine switch still off) open and close any door several times at 1.5 second intervals.

1.INSPECT IGNITION RELAY NO. 2


    B060778E92
  1. Remove the IG2 relay from the engine room R/B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Always
    10 kΩ or higher
    3 - 5
    When battery voltage is applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE IGNITION RELAY NO. 2
OK


2.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - BODY GROUND)


    C157850E30
  1. Disconnect the E69 connector from the steering lock ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E69-1 (GND) - Body ground
    Always
    Below 1 Ω
    E69-2 (SGND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (STEERING LOCK ECU - BATTERY)


    C157850E31
  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E69-6 (IG2) - E69-1 (GND)
    Engine switch on (IG)
    10 to 14 V
    E69-6 (IG2) - E69-2 (SGND)
    Engine switch on (IG)
    10 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    *E69-6 (IG2) - E69-7 (B)
    Engine switch off
    10 kΩ or higher

    *: This measurement is performed with the engine switch off to check for a short between IG2 and battery voltage.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STEERING LOCK ECU - BATTERY)
OK

REPLACE STEERING LOCK ECU (STEERING LOCK ACTUATOR ASSEMBLY) (Click here)