DTC P0365 Camshaft Position Sensor "B" Circuit (Bank 1) |
DTC P0367 Camshaft Position Sensor "B" Circuit Low Input (Bank 1) |
DTC P0368 Camshaft Position Sensor "B" Circuit High Input (Bank 1) |
DTC P0390 Camshaft Position Sensor "B" Circuit (Bank 2) |
DTC P0392 Camshaft Position Sensor "B" Circuit Low Input (Bank 2) |
DTC P0393 Camshaft Position Sensor "B" Circuit High Input (Bank 2) |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0365 P0390 |
|
|
| P0367 P0392 | Output voltage of VVT sensor is 0.3 V or less for 5 seconds (1 trip detection logic) |
|
| P0368 P0393 | Output voltage of VVT sensor is 4.7 V or more for 5 seconds (1 trip detection logic) |
|
![]() |
| Item | Content |
| Terminal | NE+ - NE- EV1+ - EV1- EV2+ - EV2- |
| Equipment Setting | 5 V/DIV. 20 ms./DIV. |
| Condition | Cranking or idling |
| 1.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE) |
![]() |
Disconnect the C40 or C44 VVT sensor connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| VC2 (C40-3) - Body ground | 4.5 to 5.0 V |
| VC2 (C44-3) - Body ground | 4.5 to 5.0 V |
Reconnect the VVT sensor connector.
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM) |
![]() |
Disconnect the C40 or C44 VVT sensor connector.
Disconnect the C58 (RHD) or C55 (LHD) ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Specified Condition |
| EX+ (C40-1) - EV1+ (C58-68) | Below 1 Ω |
| EX- (C40-2) - EV1- (C58-91) | Below 1 Ω |
| EX+ (C44-1) - EV2+ (C58-66) | Below 1 Ω |
| EX- (C44-2) - EV2- (C58-89) | Below 1 Ω |
| Tester Connection | Specified Condition |
| EX+ (C40-1) - EV1+ (C55-68) | Below 1 Ω |
| EX- (C40-2) - EV1- (C55-91) | Below 1 Ω |
| EX+ (C44-1) - EV2+ (C55-66) | Below 1 Ω |
| EX- (C44-2) - EV2- (C55-89) | Below 1 Ω |
| Tester Connection | Specified Condition |
| EX+ (C40-1) or EV1+ (C58-68) - Body ground | 10 kΩ or higher |
| EX- (C40-2) or EV1- (C58-91) - Body ground | 10 kΩ or higher |
| EX+ (C44-1) or EV2+ (C58-66) - Body ground | 10 kΩ or higher |
| EX- (C44-2) or EV2- (C58-89) - Body ground | 10 kΩ or higher |
| Tester Connection | Specified Condition |
| EX+ (C40-1) or EV1+ (C55-68) - Body ground | 10 kΩ or higher |
| EX- (C40-2) or EV1- (C55-91) - Body ground | 10 kΩ or higher |
| EX+ (C44-1) or EV2+ (C55-66) - Body ground | 10 kΩ or higher |
| EX- (C44-2) or EV2- (C55-89) - Body ground | 10 kΩ or higher |
Reconnect the VVT sensor connector.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 3.CHECK VVT SENSOR FOR EXHAUST CAMSHAFT (SENSOR INSTALLATION) |
![]() |
Check the VVT sensor installation.
|
| ||||
| OK | |
| 4.CHECK EXHAUST CAMSHAFT |
Check the teeth of the camshaft.
|
| ||||
| OK | |
| 5.REPLACE VVT SENSOR |
| NEXT | |
| 6.CHECK WHETHER DTC OUTPUT RECURS |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position.
Turn the intelligent tester on.
Clear the DTCs (Click here).
Select the following menu items: Powertrain / Engine / DTC.
Read the DTCs.
| Display (DTC Output) | Proceed to |
| No output | A |
| P0365, P0352, P0353, P0354, P0355 or P0356 | B |
|
| ||||
| A | ||
| ||