AUTOMATIC TRANSAXLE ASSEMBLY > INSTALLATION |
| 1. INSTALL TRANSAXLE CASE UPPER COVER |
![]() |
Install the transmission case upper cover with the 3 bolts.
| 2. INSTALL ENGINE MOUNTING FRONT BRACKET |
![]() |
Install the engine mounting front bracket to the automatic transaxle with the 3 bolts.
| 3. INSTALL TRANSMISSION OIL FILLER TUBE SUB-ASSEMBLY |
Coat a new O-ring with ATF, and install it to the oil filler tube.
![]() |
Install the oil filler tube to the automatic transaxle with the bolt.
Install the ATF level gauge.
| 4. INSTALL NO. 1 TRANSMISSION CONTROL CABLE BRACKET |
![]() |
Install the No. 1 control cable bracket with the 2 bolts.
| 5. INSTALL NO. 1 OIL COOLER INLET TUBE |
Temporarily install the No. 1 oil cooler outlet tube.
Temporarily install the No. 1 oil cooler inlet tube.
![]() |
Install the oil cooler tube clamp with the bolt.
![]() |
Using SST and a wrench, tighten the No. 1 oil cooler inlet tube.
| 6. INSTALL NO. 1 OIL COOLER OUTLET TUBE |
Using SST and a wrench, tighten the No. 1 oil cooler outlet tube.
| 7. CONNECT CONNECTORS |
![]() |
Connect the transmission wire connector.
Connect the park/neutral position switch connector.
Connect the 2 speed sensor connectors.
| 8. CONNECT WIRE HARNESS |
![]() |
Connect the wire harness with the bolt.
| 9. INSTALL WIRE HARNESS CLAMP BRACKET |
![]() |
Install the 2 brackets with the 2 bolts.
Connect the wire harnesses to the clamps.
| 10. INSTALL NO. 2 TRANSMISSION CONTROL CABLE BRACKET |
![]() |
Install the No. 2 transmission control cable bracket with the bolt.
| 11. INSTALL SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY |
Coat a new O-ring with ATF WS, and install it to the hole cover.
![]() |
Install the hole cover to the transaxle case with the bolt.
| 12. INSTALL TORQUE CONVERTER CLUTCH ASSEMBLY |
![]() |
Using vernier calipers and a straight edge, measure dimension "A" between the transaxle fitting part of the engine and the converter fitting part of the drive plate (#1).
![]() |
Set the key of the front oil pump drive gear to the top and put a mark on the housing.
![]() |
Put a mark on the torque converter clutch so that its groove can be clearly indicated.
![]() |
Align the 2 marks on the transaxle case and torque converter clutch and fit the splined part of the input shaft to the spline part of the turbine runner.
![]() |
Rotating the torque converter clutch, fit the spline part of the stator shaft to the spline part of the stator.
![]() |
Rotating the torque converter clutch, align the 2 marks on the case and the torque converter clutch again and fit the key of the oil pump drive gear into the key way of the torque converter clutch.
![]() |
Using vernier calipers and a straight edge, measure dimension "B" shown in the illustration and check that "B" is greater than "A" (measured in step (#1)).
| 13. INSTALL AUTOMATIC TRANSAXLE ASSEMBLY |
![]() |
Install the automatic transaxle to the engine with the 5 bolts.
![]() |
Install the 4 lower side mounting bolts.
| 14. INSTALL STARTER ASSEMBLY |
![]() |
Install the starter assembly with the 2 bolts.
![]() |
Connect the wire harness to terminal 30 and install the nut. Then, attach the terminal cap.
Connect the terminal 50 connector to the starter assembly.
| 15. INSTALL ENGINE WIRE |
| 16. INSTALL FRONT DRIVE SHAFT ASSEMBLY LH |
![]() |
Coat the spline of the inboard joint shaft assembly with ATF.
Align the shaft splines and install the drive shaft assembly LH with a brass bar and hammer.
| 17. INSTALL FRONT DRIVE SHAFT ASSEMBLY RH |
![]() |
Coat the spline of the inboard joint shaft assembly with ATF.
Install the front drive shaft the assembly RH.
Using a screwdriver, install a new bearing bracket hole snap ring.
Install a new bolt.
| 18. INSTALL FRONT FRAME ASSEMBLY |
![]() |
A/T:
Install the engine mounting insulator LH with the nut.
![]() |
M/T:
Install the engine mounting insulator LH with the bolt.
![]() |
Install the engine mounting insulator RH with the nut.
![]() |
Install the engine mounting insulator FR with the bolt.
![]() |
M/T:
Install the engine lateral control rod with the bolt.
| 19. INSTALL VANE PUMP ASSEMBLY |
![]() |
Install the vane pump to the engine with the 2 bolts.
Connect the oil pressure switch connector.
| 20. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE |
![]() |
Set the engine assembly with transaxle on the engine lifter.
Install the engine assembly to the vehicle.
Install the frame side plate LH and RH with the 4 bolts and 2 nuts.
![]() |
Install the front suspension member brace rear RH and LH with the 4 bolts and 2 nuts.
| 21. INSTALL STEERING SLIDING YOKE |
![]() |
Align the matchmarks on the steering sliding yoke and the steering link assembly.
![]() |
Install the bolt.
| 22. INSTALL DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT |
Apply a few drops of adhesive to 2 threads on the tip of the 6 torque converter clutch mounting bolts.
![]() |
Install the 6 torque converter clutch mounting bolts.
![]() |
Install the flywheel housing under cover.
| 23. INSTALL FRONT AXLE ASSEMBLY LH |
![]() |
Align the matchmarks and install the front drive shaft assembly to the front axle hub sub-assembly.
| 24. INSTALL FRONT AXLE ASSEMBLY RH |
| 25. INSTALL FRONT SUSPENSION LOWER NO. 1 ARM LH |
![]() |
Install the lower ball joint to the front suspension lower No. 1 arm with the bolt and 2 nuts.
| 26. INSTALL FRONT SUSPENSION LOWER NO. 1 ARM RH |
| 27. INSTALL TIE ROD ASSEMBLY LH |
Install the tie rod end sub-assembly to the steering knuckle with the nut.
Install a new cotter pin.
| 28. INSTALL TIE ROD ASSEMBLY RH |
| 29. INSTALL FRONT SPEED SENSOR LH |
![]() |
Install the front speed sensor to the steering knuckle with the bolt.
![]() |
Install the flexible hose and the speed sensor to the shock absorber with the bolt and set the sensor clip on the knuckle.
| 30. INSTALL FRONT SPEED SENSOR RH |
| 31. INSTALL FRONT STABILIZER LINK ASSEMBLY LH |
![]() |
Install the stabilizer link assembly with the nut.
| 32. INSTALL FRONT STABILIZER LINK ASSEMBLY RH |
| 33. INSTALL FRONT AXLE HUB NUT LH |
Clean the threaded parts on the drive shaft and front axle hub nut using a non-residue solvent.
![]() |
Using a socket wrench (30 mm), install a new axle hub nut.
Using a chisel and hammer, stake the front axle hub nut.
| 34. INSTALL FRONT AXLE HUB NUT RH |
| 35. INSTALL FRONT EXHAUST PIPE ASSEMBLY |
Install a new gasket onto the front exhaust pipe assembly.
Install the front exhaust pipe assembly with the 2 nuts.

Install the front exhaust pipe No. 1 support bracket with the 2 nuts .
| 36. CONNECT COMPRESSOR AND MAGNETIC CLUTCH |
![]() |
Install the cooler compressor with the 4 bolts.
| 37. INSTALL GENERATOR ASSEMBLY |
![]() |
Confirm that the wire harness of the crankshaft position sensor is secured to the wire harness clamp bracket through the back of the rib of the timing chain cover.
![]() |
Install the generator assembly with the 2 bolts.
![]() |
Install the generator wire to terminal B with the nut.
Install the clamp bracket with the bolt.
Attach the clamp and connect the generator connector to the generator.
| 38. CONNECT FUEL TUBE SUB-ASSEMBLY |
![]() |
Push in the fuel tube connector to the fuel pipe until the connector makes a "click" sound.
![]() |
Install the No. 1 fuel pipe clamp.
| 39. CONNECT RETURN TUBE SUB-ASSEMBLY |
![]() |
Connect the return tube sub-assembly.
| 40. CONNECT NO. 1 OIL RESERVOIR TO PUMP HOSE |
![]() |
Connect the No. 1 oil reservoir to pump hose.
| 41. CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY |
![]() |
Connect the transmission control cable assembly to the control cable clamp.
![]() |
Connect the transmission control cable to the bracket with a new clip.
![]() |
Connect the transmission control cable assembly to the control shaft lever with the nut.
| 42. CONNECT ENGINE WIRE |
![]() |
Install the 2 bolts and clamp to the body.
![]() |
Connect the clamp to the bracket.
![]() |
Connect the wire to the engine room junction block. Then, install it with the nut and 3 connectors.
| 43. INSTALL ECM |
| 44. CONNECT HEATER WATER HOSE INLET |
![]() |
Connect the heater inlet water hose.
| 45. CONNECT HEATER WATER HOSE OUTLET |
![]() |
Connect the heater outlet water hose.
| 46. CONNECT OIL COOLER INLET HOSE |
![]() |
Connect the oil cooler inlet hose to the radiator assembly.
| 47. CONNECT OIL COOLER OUTLET HOSE |
![]() |
Connect the oil cooler outlet hose to the radiator assembly.
| 48. CONNECT RADIATOR HOSE INLET |
![]() |
Connect the radiator hose inlet to the radiator assembly.
| 49. CONNECT RADIATOR HOSE OUTLET |
![]() |
Connect the radiator hose outlet to the radiator assembly.
| 50. CONNECT NO. 1 VACUUM HOSE CONNECTOR |
![]() |
Install the clamp and connect the vacuum hose connector.
| 51. INSTALL NO. 2 ENGINE MOUNTING BRACKET RH |
![]() |
Install the 3 bolts and No. 2 mounting bracket RH.
| 52. INSTALL ENGINE MOVING CONTROL ROD SUB-ASSEMBLY |
![]() |
Install the engine moving control rod with the 3 bolts.
![]() |
Install the ground cable with the bolt.
| 53. INSTALL NO. 2 ENGINE MOUNTING STAY RH |
![]() |
Install the No. 2 mounting stay RH with the 2 bolts.
| 54. INSTALL BATTERY |
Install the battery and battery tray.
![]() |
Install the battery clamp with the bolt and nut.
| 55. INSTALL AIR CLEANER CASE SUB-ASSEMBLY |
![]() |
Install the air cleaner case with the 3 bolts.
Connect the hose clamp.
| 56. INSTALL AIR CLEANER CAP SUB-ASSEMBLY |
Install the air cleaner filter element onto the air cleaner case.
![]() |
Insert the hinges. Install the air cleaner cap sub-assembly with the 2 bolts.
![]() |
Align the matchmarks of the No. 1 air cleaner hose and throttle body, and then connect the air cleaner hose No. 1 to the throttle body and unfasten the No. 1 air cleaner hose clamp.
![]() |
Connect the No. 2 ventilation hose to the air cleaner hose.
![]() |
Connect the purge line hose to the clamp (*1).
Connect the 2 purge VSV vacuum hoses (*2).
Connect the purge VSV connector (*3).
Connect the mass air flow meter connector (*4).
| 57. INSTALL AIR CLEANER INLET ASSEMBLY |
![]() |
Install the air cleaner inlet with the 2 bolts.
| 58. INSTALL V-RIBBED BELT |
![]() |
Using SST and 19 mm socket wrench, loosen the V-ribbed belt tensioner arm clockwise, then install the V-ribbed belt.
After installing the V-ribbed belt, check that it fits properly in the ribbed grooves. Check to confirm that the belt has not slipped out of the grooves on the bottom of the crank pulley by hand.
| 59. INSTALL COWL TOP PANEL OUTER SUB-ASSEMBLY |
![]() |
Install the outer cowl top panel sub-assembly with the 4 bolts and 4 nuts.
| 60. INSTALL WINDSHIELD WIPER LINK ASSEMBLY |
| 61. INSTALL FRONT WHEEL |
| 62. ADD ENGINE OIL |
| 63. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL |
| 64. ADD ENGINE COOLANT |
Close the radiator drain cock plug and 2 cylinder block drain cock plugs.
Slowly fill the radiator with TOYOTA Super Long Life Coolant (SLLC).
Slowly pour coolant into the radiator reservoir tank until it reaches the FULL line.
Press the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.
If the coolant level is low, add coolant.
Install the radiator cap sub-assembly and reservoir tank cap.
Start the engine, and warm it up.
Stop the engine, and wait until the engine coolant cools down.
Add engine coolant to the FULL line on the radiator reservoir.
| 65. ADD AUTOMATIC TRANSAXLE FLUID |
| 66. ADD POWER STEERING FLUID |
| 67. BLEED POWER STEERING FLUID |
Check the fluid level .
Jack up the front of the vehicle and support it with stands.
Turn the steering wheel.
With the engine stopped, turn the steering wheel slowly from lock to lock several times.
Lower the vehicle.
Start the engine.
Run the engine at idle for a few minutes.
Turn the steering wheel.
With the engine idling, turn the steering wheel left or right to the full lock position and keep it in that position for 2 to 3 seconds, then turn the steering wheel to the opposite full lock position and keep it there for 2 to 3 seconds.
Repeat this procedure several times.
Stop the engine.
![]() |
Check for foaming or emulsification.
Check the fluid level .
| 68. INSPECT AUTOMATIC TRANSAXLE FLUID |
![]() |
Park the vehicle on a level surface and set the parking brake.
With the engine idling and the brake pedal depressed, move the shift lever to all positions from P to L. Then return it to P.
Pull out the dipstick and wipe it clean.
Push it back fully into the pipe.
Pull it out again and check that the fluid level is within the HOT range. If the fluid level is below the HOT range, add new fluid and recheck the fluid level. If the fluid level exceeds the HOT range, drain the fluid once, add proper amount of new fluid and recheck the fluid level.
| 69. CHECK FOR FUEL LEAKS |
Check fuel pump operation.
Connect the intelligent tester to the DLC3.
Turn the ignition switch to the ON position and push the intelligent tester main switch on.
Select the following menus: Powertrain / Engine / Active Test / Control the Fuel Pump /Speed.
Check for pressure in the fuel inlet tube from the fuel line. Check that sound of fuel flowing in the fuel tank can be heard. If no sound can be heard, check the integration relay, fuel pump, ECM and wiring connector.
Check for fuel leaks.
Check that there are no fuel leaks anywhere on the system after performing maintenance. If there is a fuel leak, repair or replace parts as necessary.
Turn the ignition switch off.
Disconnect the intelligent tester from the DLC3.
| 70. CHECK FOR ENGINE OIL LEAKS |
| 71. CHECK FOR ENGINE COOLANT LEAKS |
![]() |
Fill the radiator with coolant and attach a radiator cap tester.
Warm up the engine.
Using a radiator cap tester, increase the pressure inside the radiator to 118 kPa (1.2 kgf*cm, 17 psi), and check that the pressure does not drop.
If the pressure drops, check the hoses, radiator and water pump for leaks. If no external leaks are found, check the heater core, cylinder block and cylinder head.
| 72. CHECK FOR EXHAUST GAS LEAKS |
| 73. CHECK FOR SHIFT LEVER POSITION |
When shifting from the P to the R position with the ignition switch on and the brake pedal depressed, make sure that the shift lever moves smoothly and moves correctly into the position.
Start the engine and make sure that the vehicle moves forward when shifting from the N to the D position and moves rearward when shifting to the R position. If operation cannot be done as specified, inspect the park/neutral position switch assembly and check the shift lever assembly installation condition.
| 74. ADJUST SHIFT LEVER POSITION |
Move the shift lever to the N position.
![]() |
Remove the nut from the control shaft lever.
Disconnect the transmission control cable assembly from the control shaft lever.
![]() |
Push the control shaft fully downward.
Return the control shaft lever 2 notches to the N position.
![]() |
Move the slider in the directions indicated by the arrows and pull up the lock piece.
![]() |
Connect the transmission control cable assembly to the control shaft lever with the nut.
![]() |
Push in the lock piece.
Start the engine and make sure that the vehicle moves forward when moving the lever from the N to the D position and moves rearward when moving it to the R position.
If it becomes hard to move the shift lever, readjust the shift lever position.
| 75. INSPECT AND ADJUST FRONT WHEEL ALIGNMENT |
| 76. CHECK IGNITION TIMING |
Warm up the engine.
![]() |
When using the intelligent tester:
Check the ignition timing.
Connect the intelligent tester to the DLC3.
Enter DATA LIST MODE on the intelligent tester.
![]() |
When not using the intelligent tester:
Check the ignition timing.
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3.
![]() |
Remove the No. 1 engine cover.
Pull out the wire harness as shown in the illustration. Connect the clip of the timing light to the wire harness.
Check the ignition timing at idle.
Disconnect terminals 13 (TC) and 4 (CG) of the DLC3.
Check the ignition timing at idle.
Confirm that the ignition timing moves to the advanced angle side when the engine rpm is increased.
Remove the timing light.
| 77. CHECK ENGINE IDLE SPEED |
![]() |
Warm up the engine.
When using the intelligent tester:
Check the idle speed.
Connect the intelligent tester to the DLC3.
Enter DATA LIST MODE on the intelligent tester.
| Item | Specified Condition |
| M/T | 650 to 750 rpm |
| A/T | 610 to 710 rpm |
![]() |
When not using the intelligent tester:
Check the idle speed.
Using SST, connect the tachometer tester probe to terminal 9 (TAC) of the DLC3.
Check the idle speed.
| Item | Specified Condition |
| M/T | 650 to 750 rpm |
| A/T | 610 to 710 rpm |
| 78. INSPECT CO/HC |
Start the engine.
Run the engine at 2,500 rpm for approximately 180 seconds.
Insert the CO/HC meter testing probe at least 40 cm (1.3 ft) into the tailpipe during idling.
Immediately check CO/HC concentration at idle and/or 2,500 rpm.
If the CO/HC concentration does not comply with regulations, troubleshoot in the order given below.
Check A/F sensor operation .
Check heated oxygen sensor operation .
See the table below for possible causes, and then inspect and repair.
| CO | HC | Problems | Causes |
| Normal | High | Rough idle |
|
| Low | High | Rough idle (fluctuating HC reading) |
|
| High | High | Rough idle (black smoke from exhaust) |
|
| 79. INSTALL FRONT FENDER APRON SEAL RH |
| 80. INSTALL ENGINE UNDER COVER LH |
| 81. INSTALL ENGINE UNDER COVER RH |
| 82. INSTALL NO. 1 ENGINE COVER SUB-ASSEMBLY |
![]() |
Install the engine cover with the 2 nuts.
| 83. CHECK ABS SPEED SENSOR SIGNAL |