AUTOMATIC TRANSAXLE UNIT > INSPECTION |
| 1. INSPECT MULTIPLE DISC CLUTCH HUB |
![]() |
Using a dial indicator, measure the inside diameter of the multiple disc clutch hub bushing.
| 2. INSPECT NO. 2 UNDERDRIVE CLUTCH DISC |
![]() |
Check if the sliding surfaces of the discs, plates and flange are worn or burnt.
If necessary, replace them.
| 3. INSPECT OVERDRIVE DIRECT CLUTCH DRUM SUB-ASSEMBLY |
![]() |
Using a dial indicator, measure the inside diameter of the overdrive direct clutch drum sub-assembly bushing.
| 4. INSPECT 2ND BRAKE DISC |
![]() |
Check if the sliding surfaces of the discs, plates and flange are worn or burnt.
If necessary, replace them.
| 5. INSPECT 1ST AND REVERSE BRAKE DISC |
![]() |
Check if the sliding surfaces of the discs, plates and flange are worn or burnt.
If necessary, replace them.
| 6. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY |
![]() |
Using vernier calipers, measure the free length of the spring together with the spring seat.
| 7. INSPECT UNDERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY |
![]() |
Using vernier calipers, measure the free length of the spring together with the spring seat.
| 8. INSPECT PACK CLEARANCE OF FIRST AND REVERSE BRAKE |
![]() |
Using vernier calipers, measure the distance between the disc surface and the contact surface of the 2nd brake cylinder and transaxle case (Dimension A).
Select an appropriate flange so that the pack clearance will be within the specified range.
| Mark | Thickness | Mark | Thickness |
| 1 | 1.8 (0.071) | 5 | 2.2 (0.087) |
| 2 | 1.9 (0.075) | 6 | 2.3 (0.091) |
| 3 | 2.0 (0.079) | 7 | 2.4 (0.094) |
| 4 | 2.1 (0.083) | 8 | 2.5 (0.098) |
Install the flange.
| 9. INSPECT PACK CLEARANCE OF SECOND BRAKE |
![]() |
Using vernier calipers, measure the distance between the disc surface and snap ring surface (Dimension B).
Select an appropriate flange so that the pack clearance will be within the specified range.
| Mark | Thickness | Mark | Thickness |
| 0 | 2.9 (0.114) | 5 | 3.4 (0.134) |
| 1 | 3.0 (0.118) | 6 | 3.5 (0.138) |
| 2 | 3.1 (0.122) | 7 | 3.6 (0.142) |
| 3 | 3.2 (0.126) | 8 | 3.7 (0.146) |
| 4 | 3.3 (0.130) | - | - |
Install the flange.
| 10. INSPECT PACK CLEARANCE OF NO. 2 UNDERDRIVE CLUTCH |
![]() |
Using a dial indicator, measure the underdrive clutch pack clearance while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).
Select an appropriate flange from the table below so that the pack clearance will be within the specified range.
| Mark | Thickness | Mark | Thickness |
| Y | 2.8 (0.110) | C | 3.4 (0.134) |
| A | 3.0 (0.118) | D | 3.6 (0.142) |
| B | 3.2 (0.126) | - | - |
Temporarily remove the snap ring and attach the flange to the transaxle case.
Reinstall the snap ring to the transaxle case.
| 11. INSPECT UNDERDRIVE ONE-WAY CLUTCH ASSEMBLY |
![]() |
Install the underdrive clutch assembly to the one-way clutch.
Rotate the underdrive clutch assembly to check the rotating direction for the lock or free operation.
Remove the underdrive clutch assembly from the one-way clutch.
| 12. INSPECT INPUT SHAFT END PLAY |
![]() |
Using a dial indicator, measure the input shaft end play.
| 13. INSPECT DIRECT MULTIPLE DISC CLUTCH DISC |
![]() |
Check if the sliding surfaces of the discs, plates, and flange are worn or burnt. If necessary, replace them.
| 14. INSPECT OVERDRIVE DIRECT CLUTCH DISC |
![]() |
Check if the sliding surfaces of the discs, plates, and flange are worn or burnt. If necessary, replace them.
| 15. INSPECT OVERDRIVE CLUTCH RETURN SPRING SUB-ASSEMBLY |
![]() |
Using vernier calipers, measure the free length of the spring together with the spring seat.
| 16. INSPECT PACK CLEARANCE OF DIRECT CLUTCH |
![]() |
Install the intermediate shaft and needle roller bearing on the transaxle rear cover.
Using a dial indicator, measure the direct clutch pack clearance while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).
| 17. INSPECT PACK CLEARANCE OF OVERDRIVE CLUTCH |
![]() |
Using a dial indicator, measure the overdrive clutch pack clearance while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).
| 18. INSPECT PACK CLEARANCE OF DIRECT CLUTCH |
![]() |
Install the intermediate shaft on the transaxle rear cover.
Using a dial indicator, measure the direct clutch pack clearance while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).
| Mark | Thickness | Mark | Thickness |
| 0 | 2.9 (0.114) | 4 | 3.3 (0.130) |
| 1 | 3.0 (0.118) | 5 | 3.4 (0.134) |
| 2 | 3.1 (0.122) | 6 | 3.5 (0.138) |
| 3 | 3.2 (0.126) | 7 | 3.6 (0.142) |
| 19. INSPECT PACK CLEARANCE OF OVERDRIVE CLUTCH |
![]() |
Using a dial indicator, measure the overdrive clutch pack clearance while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).
| Mark | Thickness | Mark | Thickness |
| 0 | 2.5 (0.098) | 4 | 2.9 (0.114) |
| 1 | 2.6 (0.102) | 5 | 3.0 (0.118) |
| 2 | 2.7 (0.106) | 6 | 3.1 (0.122) |
| 3 | 2.8 (0.110) | - | - |
![]() |
Check that the disc rotates when rotating the disc after inserting the rear planetary sun gear.
| 20. INSPECT 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY |
![]() |
Using vernier calipers, measure the free length of the spring together with the spring seat.