Home › TRANSMISSION · U250E AUTOMATIC TRANSAXLE › AUTOMATIC TRANSAXLE UNIT

AUTOMATIC TRANSAXLE UNIT > DISASSEMBLY

for Preparation Click here



1. REMOVE PARK/NEUTRAL POSITION SWITCH ASSEMBLY


    C135707
  1. Remove the nut, washer, and control shaft lever.



    C135708
  1. Using a screwdriver, unstake the lock plate, and remove the lock nut and nut stopper.



    C135710
  1. Remove the 2 bolts and pull out the park/neutral position switch.



2. REMOVE NO. 2 BREATHER PLUG


    C134833
  1. Remove the No. 2 breather plug from the transaxle case.



    C134834E01
  1. Remove the hose and O-ring from the No. 2 breather plug.



3. REMOVE OIL COOLER TUBE UNION (INLET OIL COOLER UNION)


    C083143E03
  1. Remove the union.

  1. Remove the O-ring from the union.



4. REMOVE OIL COOLER TUBE UNION (OUTLET OIL COOLER UNION)


    C083144E04
  1. Remove the union.

  1. Remove the O-ring from the union.



5. REMOVE SPEED SENSOR


    D030672E04
  1. Remove the 2 bolts and the 2 speed sensors from the transaxle assembly.



6. REMOVE NO. 1 TRANSAXLE CASE PLUG


    C134835
  1. Remove the 4 No. 1 transaxle case plugs from the transaxle case.

  1. Remove the 4 O-rings from the 4 No. 1 transaxle case plugs.



7. FIX AUTOMATIC TRANSAXLE ASSEMBLY


    C134836
  1. Fix the transaxle assembly.



8. REMOVE AUTOMATIC TRANSAXLE OIL PAN SUB-ASSEMBLY
  1. Remove the drain plug and drain plug gasket from the oil pan.



    C091925
  1. Remove the 18 bolts, oil pan, and gasket.



    C134837E01
  1. Remove the 2 transmission oil cleaner magnets from the oil pan.



9. INSPECT TRANSMISSION OIL CLEANER MAGNET


    AT00103E03
  1. Remove the magnets and use them to collect any steel chips. Examine the chips and particles in the pan and on the magnet to determine what type of wear has occurred in the transaxle:

    Result:
    Steel (magnetic):
    bearing, gear, and plate wear
    Brass (non-magnetic):
    bushing wear



10. DISCONNECT TRANSMISSION WIRE


    C134838E01
  1. Disconnect the 7 connectors from the shift solenoid valves.

  1. Remove the bolt, lock plate, and ATF temperature sensor.



11. REMOVE TRANSMISSION WIRE


    D003547E05
  1. Remove the bolt and transmission wire from the transaxle case.



12. REMOVE VALVE BODY OIL STRAINER ASSEMBLY


    C134839
  1. Remove the 3 bolts and oil strainer.



    C091932E02
  1. Remove the O-ring from the oil strainer.



13. REMOVE TRANSMISSION VALVE BODY ASSEMBLY


    C091933
  1. Support the valve body assembly and remove the 17 bolts and valve body assembly.



14. REMOVE NO. 1 GOVERNOR APPLY GASKET


    C083127
  1. Remove the No. 1 governor apply gasket from the transaxle case.



15. REMOVE TRANSAXLE CASE 2ND BRAKE GASKET


    C083128
  1. Remove the transaxle case 2nd brake gasket from the transaxle case.



16. REMOVE BRAKE DRUM GASKET


    C083129
  1. Remove the brake drum gasket from the transaxle case.



17. REMOVE CHECK BALL BODY


    D003554E01
  1. Remove the check ball body and spring from the transaxle case.



18. REMOVE C-3 ACCUMULATOR PISTON


    D003555
  1. Remove the spring from the C-3 accumulator piston.



    C134840
  1. Using needle-nose pliers, remove the the C-3 accumulator piston from the transaxle case.



    C134841E01
  1. Remove the O-ring from the C-3 accumulator piston.



19. REMOVE REVERSE CLUTCH ACCUMULATOR PISTON


    D026401
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the reverse accumulator piston and spring.

    NOTICE:
    1. Applying compressed air may cause the piston to jump-out. When removing the piston, hold it by hand using a waste cloth.
    2. Take care not to splash ATF when applying the air.



    D026402E07
  1. Remove the 2 O-rings from the reverse clutch accumulator piston.



20. REMOVE B-3 ACCUMULATOR PISTON


    D003558E01
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the oil hole and remove the B-3 accumulator piston and 2 springs.

    NOTICE:
    1. Applying compressed air may cause the piston to jump-out. When removing the piston, hold it by hand using a waste cloth.
    2. Take care not to splash ATF when applying the air.



    D003904E06
  1. Remove the O-ring from the B-3 accumulator piston.



21. REMOVE MANUAL VALVE LEVER SHAFT RETAINER SPRING


    D003559
  1. Using needle-nose pliers, remove the manual valve lever shaft retainer spring.



22. REMOVE MANUAL DETENT SPRING SUB-ASSEMBLY


    D003560
  1. Remove the 2 bolts and manual detent spring sub-assembly.



23. REMOVE PARKING LOCK PAWL BRACKET


    C056727
  1. Remove the 2 bolts and parking lock pawl bracket.



24. REMOVE MANUAL VALVE LEVER SUB-ASSEMBLY


    C134842E01
  1. Using a screwdriver, slide the spacer.



    C134843
  1. Using a pin punch (φ3 mm) and hammer, drive out the pin.

    HINT:
    Slowly drive out the pin so that it will not fall into the transaxle case.



    C134844
  1. Remove the manual valve lever shaft, manual valve lever, and spacer.



25. REMOVE PARKING LOCK ROD SUB-ASSEMBLY


    C134845E01
  1. Remove the parking lock rod sub-assembly from the manual valve lever sub-assembly.

    HINT:
    Align the dial with the notches on the manual valve lever sub-assembly to remove the parking lock rod sub-assembly.



26. REMOVE MANUAL VALVE LEVER SHAFT OIL SEAL


    D003566
  1. Using a screwdriver, remove the oil seal from the transaxle case.



27. FIX AUTOMATIC TRANSAXLE ASSEMBLY
  1. Fix the transaxle case with the oil pump side facing up.



28. INSPECT INPUT SHAFT END PLAY


    D008091
  1. Using a dial indicator, measure the input shaft end play.

    End play:
    0.262 to 1.244 mm (0.01 to 0.049 in.)



29. REMOVE TRANSAXLE HOUSING


    C115282
  1. Remove the 16 bolts.

  1. Tap on the circumference of the transaxle housing with a plastic hammer to remove the transaxle housing from the transaxle case.

    NOTICE:
    The differential may be accidentally removed when the transaxle housing is removed.



30. REMOVE OIL PUMP ASSEMBLY


    D003569E03
  1. Remove the 7 bolts and oil pump from the transaxle case.



31. REMOVE THRUST NEEDLE ROLLER BEARING


    D025505E04
  1. Remove the thrust needle roller bearing from the underdrive planetary gear assembly.



32. REMOVE NO. 2 THRUST BEARING UNDERDRIVE RACE


    D025506E05
  1. Remove the No. 2 thrust bearing underdrive race from the underdrive planetary gear assembly.



33. REMOVE DIFFERENTIAL GEAR ASSEMBLY


    D026450E07
  1. Remove the differential gear assembly from the transaxle case.



34. REMOVE OVERDRIVE BRAKE GASKET


    D003573
  1. Remove the 2 overdrive brake gaskets from the transaxle case.



35. REMOVE FORWARD CLUTCH ASSEMBLY


    D003574E04
  1. Remove the forward clutch assembly from the transaxle case.



    D003906E03
  1. Remove the thrust needle roller bearing from the forward clutch.



36. REMOVE MULTIPLE DISC CLUTCH HUB


    D026787E05
  1. Remove the thrust needle roller bearing, multiple disc clutch hub, thrust needle roller bearing and No. 1 thrust bearing race from the transaxle case.



37. INSPECT MULTIPLE DISC CLUTCH HUB


    D003829E06
  1. Using a dial indicator, measure the inside diameter of the multiple disc clutch hub bushing.

    Standard inside diameter:
    23.025 to 23.046 mm (0.9065 to 0.9073 in.)

    Maximum inside diameter:
    23.09 mm (0.9091 in.)

    If the diameter is greather than the maximum, replace the multiple disc clutch hub with a new one.

    NOTICE:
    Check the contact surface of the bushing in the direct clutch shaft. If any scratch or discolor is identified, replace the direct clutch sub-assembly with a new one.



38. REMOVE UNDERDRIVE PLANETARY GEAR ASSEMBLY


    D003576E04
  1. Remove the bolt and pawl shaft clamp from the transaxle case.



    D009652
  1. Remove the parking lock pawl shaft from the transaxle case.



    D009689
  1. Push the parking lock pawl.

    HINT:
    Failure to do so will cause interference when the underdrive planetary gear is removed.



    D003579E05
  1. Remove the underdrive planetary gear assembly from the transaxle case.

    NOTICE:
    Do not drop the underdrive planetary gear assembly.



39. REMOVE PARKING LOCK PAWL


    D026386
  1. Remove the spring, pawl pin and parking lock pawl.



40. REMOVE UNDERDRIVE CLUTCH ASSEMBLY


    D003580E03
  1. Remove the underdrive clutch assembly, thrust bearing, and bearing race from the transaxle case.



41. REMOVE UNDERDRIVE ONE-WAY CLUTCH ASSEMBLY


    D003581E03
  1. Using a screwdriver, remove the snap ring from the transaxle case.



    C134846E01
  1. Remove the underdrive one-way clutch from the transaxle case.



    D003907E01
  1. Remove the outer race retainer from the one-way clutch.



42. REMOVE NO. 2 UNDERDRIVE CLUTCH DISC


    D026466E01
  1. Using a screwdriver, remove the snap ring.



    C134847E01
  1. Remove the flange, 3 discs and 3 plates from the transaxle case.



43. INSPECT NO. 2 UNDERDRIVE CLUTCH DISC


    D009196
  1. Check if the sliding surfaces of the discs, plates and flange are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the linings of the discs are peeled off or discolored, or even if a part of the groove is damaged, replace all discs.
    2. Before assembling new discs, soak them in ATF for at least 15 minutes.



44. REMOVE TRANSAXLE REAR COVER SUB-ASSEMBLY


    C134848
  1. Remove the 11 bolts.

  1. Tap on the circumference of the rear cover with a plastic hammer to remove the transaxle rear cover from the transaxle case.



45. REMOVE NO. 1 TRANSAXLE CASE PLUG


    C134849
  1. Remove the 4 No. 1 transaxle case plugs from the transaxle rear cover.

  1. Remove the 4 O-rings from the 4 No. 1 transaxle case plugs.



46. REMOVE REAR CLUTCH OIL SEAL RING


    D026389E02
  1. Remove the 3 rear clutch oil seal rings from the transaxle rear cover.



47. REMOVE NEEDLE ROLLER BEARING


    D026472E01
  1. Using SST, remove the needle roller bearing from the transaxle rear cover.

    SST
    09387-00041   (09387-01021, 09387-01030, 09387-01040)



48. REMOVE NO. 1 GOVERNOR APPLY GASKET


    D026390
  1. Using a screwdriver, remove the 3 apply gaskets.



49. REMOVE BRAKE APPLY TUBE


    C134851E01
  1. Remove the bolt, clamp and brake apply tube.

  1. Remove the clutch apply tube.

  1. Remove the brake apply tube from the clamp.



50. REMOVE DIRECT CLUTCH ASSEMBLY


    D026403E04
  1. Remove the thrust bearing and the direct clutch assembly from the transaxle case.



51. INSPECT PACK CLEARANCE OF DIRECT CLUTCH


    C134884
  1. Install the intermediate shaft and needle roller bearing on the transaxle rear cover.

    NOTICE:
    Be careful not to damage the oil seal ring outers.

  1. Using a dial indicator, measure the direct clutch pack clearance while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).

    Pack clearance:
    0.60 to 0.82 mm (0.02362 to 0.03228 in.)

    If the pack clearance is not as specified, inspect the discs, plates and flange.



52. INSPECT PACK CLEARANCE OF OVERDRIVE CLUTCH


    C134885
  1. Using a dial indicator, measure the overdrive clutch pack clearance while applying and releasing compressed air (392 kPa, 4.0 kgf/cm2, 57 psi).

    Pack clearance:
    0.52 to 0.83 mm (0.02047 to 0.03268 in.)

    If the pack clearance is not as specified, inspect the discs, plates and flange.



53. REMOVE DIRECT MULTIPLE DISC CLUTCH DISC


    D026419E01
  1. Using a screwdriver, remove the snap ring from the intermediate shaft.



    D026420
  1. Remove the flange, 3 discs, 3 plates and cushion plate from the intermediate shaft.



54. INSPECT DIRECT MULTIPLE DISC CLUTCH DISC


    C134886
  1. Check if the sliding surfaces of the discs, plates, and flange are worn or burnt. If necessary, replace them.

    NOTICE:
    1. If the lining of a disc comes off or discolors, or a groove is damaged, replace all discs.
    2. Before assembling new discs, soak them in ATF for at least 15 minutes.



55. REMOVE OVERDRIVE DIRECT CLUTCH DISC


    C134887
  1. Using a screwdriver, remove the snap ring from the intermediate shaft.

  1. Remove the flange, 3 discs and 3 plates from the intermediate shaft.



56. INSPECT OVERDRIVE DIRECT CLUTCH DISC


    D026719
  1. Check if the sliding surfaces of the discs, plates, and flange are worn or burnt. If necessary, replace them.

    NOTICE:
    1. If the lining of a disc comes off or discolors, or a groove is damaged, replace all discs.
    2. Before assembling new discs, soak them in ATF for at least 15 minutes.



57. REMOVE OVERDRIVE CLUTCH RETURN SPRING SUB-ASSEMBLY


    D003677E01
  1. Place SST on the clutch balancer and compress the spring with a press.

    SST
    09387-00020  

  1. Using a snap ring expander, remove the snap ring from the direct clutch drum.

    NOTICE:
    1. Stop the press when the spring seat is lowered to the place 1 to 2 mm (0.039 to 0.078 in.) from the snap ring groove. This prevents the spring seat from being deformed.
    2. Do not expand the snap ring excessively.



    D026424E02
  1. Remove the clutch balancer from the overdrive direct clutch drum.



    D026423E05
  1. Remove the overdrive clutch return spring from the overdrive direct clutch drum.



58. INSPECT OVERDRIVE CLUTCH RETURN SPRING SUB-ASSEMBLY


    D009211E02
  1. Using vernier calipers, measure the free length of the spring together with the spring seat.

    Standard free length:
    25.91 mm (1.0201 in.)

    If the free length is shorter than the standard free length, replace the overdrive clutch return spring sub-assembly.



59. REMOVE OVERDRIVE DIRECT CLUTCH PISTON


    D026463
  1. Install the intermediate shaft on the transaxle rear cover.

  1. Holding the direct clutch piston by hand, apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transaxle rear cover to remove the direct clutch piston.



60. REMOVE OVERDRIVE DIRECT CLUTCH DRUM SUB-ASSEMBLY


    D026425
  1. Holding the direct clutch drum by hand, apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transaxle rear cover to remove the direct clutch drum.



61. REMOVE OVERDRIVE DIRECT CLUTCH O-RING


    D026464E01
  1. Using a screwdriver, remove the O-ring from the direct clutch drum.



62. REMOVE OVERDREVE DIRECT CLUTCH HUB SUB-ASSEMBLY


    D026392E05
  1. Remove the thrust bearing race, thrust bearing, and overdrive direct clutch hub from the planetary gear assembly.



63. REMOVE REAR PLANETARY SUN GEAR ASSEMBLY


    D026714E04
  1. Remove the rear planetary sun gear assembly from the transaxle case.



    C134852
  1. Remove the thrust needle roller bearing and thrust bearing race from the rear planetary sun gear assembly.



    D026393E02
  1. Remove the No. 2 planetary carrier thrust washer from the rear planetary sun gear assembly.



64. REMOVE ONE-WAY CLUTCH ASSEMBLY


    D026598E04
  1. Remove the one-way clutch assembly and the thrust needle roller bearing from the transaxle case.



    D003909E05
  1. Remove the one-way clutch inner race from the one-way clutch assembly.



65. REMOVE ONE-WAY CLUTCH SLEEVE


    D003589E06
  1. Remove the one-way clutch sleeve from the transaxle case.



66. REMOVE NO. 1 PLANETARY CARRIER THRUST WASHER


    C134853E01
  1. Remove the No. 1 planetary carrier thrust washer from the planetary gear assembly.



67. REMOVE 2ND BRAKE DISC


    C134854E01
  1. Using a screwdriver, remove the snap ring.

  1. Remove the flange, 3 discs and 3 plates from the transaxle case.



68. INSPECT 2ND BRAKE DISC


    D026717
  1. Check if the sliding surfaces of the discs, plates and flange are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the linings of the discs are peeled off or discolored, or even if a part of the groove is damaged, replace all discs.
    2. Before assembling new discs, soak them in ATF for at least 15 minutes.



69. REMOVE SECOND BRAKE PISTON ASSEMBLY


    D008058E04
  1. Using a screwdriver, remove the snap ring.



    D026396E05
  1. Remove the second brake piston assembly from the transaxle case.



70. REMOVE 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


    D026703E01
  1. Place SST on the return spring and compress it with a press.

    SST
    09387-00060  

  1. Using a screwdriver, remove the snap ring.



    D026704E03
  1. Remove the 2nd brake piston return spring sub-assembly.



71. INSPECT 2ND BRAKE PISTON RETURN SPRING SUB-ASSEMBLY


    C089124E02
  1. Using vernier calipers, measure the free length of the spring together with the spring seat.

    Standard free length:
    16.61 mm (0.6539 in.)

    If the free length is shorter than the standard free length, replace the 2nd brake piston return spring sub-assembly.



72. REMOVE 2ND BRAKE PISTON


    D026705
  1. Hold the 2nd brake piston and apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the 2nd brake cylinder to remove the 2nd brake piston.



73. REMOVE 2ND BRAKE PISTON O-RING


    D026706E04
  1. Remove the 2 O-rings from the 2nd brake piston.



74. REMOVE REAR PLANETARY GEAR ASSEMBLY


    D003616E01
  1. Using a screwdriver, remove the snap ring.



    D026591E03
  1. Remove the rear planetary gear assembly from the transaxle case.



75. REMOVE INPUT SUN GEAR


    C134855E01
  1. Remove the 2 thrust needle roller bearings, No. 2 thrust bearing races, No. 3 thrust bearing race, and input sun gear from the transaxle case.



76. REMOVE 1ST AND REVERSE BRAKE DISC


    C134856
  1. Remove the flange, 5 discs and 5 plates from the transaxle case.



77. INSPECT 1ST AND REVERSE BRAKE DISC


    D009189
  1. Check if the sliding surfaces of the discs, plates and flange are worn or burnt.
    If necessary, replace them.

    NOTICE:
    1. If the linings of the discs are peeled off or discolored, or even if a part of the groove is damaged, replace all discs.
    2. Before assembling new discs, soak them in ATF for at least 15 minutes.



78. REMOVE FRONT PLANETARY GEAR ASSEMBLY


    D003595E03
  1. Using a chisel and hammer, unstake the lock washer.

    NOTICE:
    Push down all claws of the washer. Otherwise SST cannot be fully pressed against the nut, and the nut cannot be loosened.



    D003596E01
  1. Using SST, remove the nut and washer.

    SST
    09387-00030  
    09387-00080  



    D026398E01
  1. Using SST and a press, remove the front planetary gear assembly from the counter drive gear.

    SST
    09950-60010   (09951-00450)
    09950-70010   (09951-07100)



    D026763E02
  1. Remove the front planetary gear assembly from the brake hub.



79. REMOVE FRONT PLANETARY RING GEAR


    D003615E04
  1. Using a screwdriver, remove the snap ring and front planetary ring gear from the brake hub.



80. REMOVE 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY


    D003600E01
  1. Place SST on the return spring, and compress the return spring with a press.

    SST
    09387-00070  

  1. Using a snap ring expander, remove the snap ring.

    NOTICE:
    1. Stop the press when the spring seat is lowered to the place 1 to 2 mm (0.039 to 0.078 in.) from the snap ring groove to prevent the spring seat from being deformed.
    2. Do not expand the snap ring excessively.

  1. Remove the return spring.



81. INSPECT 1ST AND REVERSE BRAKE RETURN SPRING SUB-ASSEMBLY


    C141534
  1. Using vernier calipers, measure the free length of the spring together with the spring seat.

    Standard free length:
    17.63 mm (0.6941 in.)

    If the free length is shorter than the standard free length, replace the 1st and reverse brake return spring sub-assembly.



82. REMOVE 1ST AND REVERSE BRAKE PISTON


    D026405E02
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transaxle case to remove the 1st and reverse brake piston.

    NOTICE:
    1. Applying compressed air may cause the piston to jump-out. When removing the piston, hold it by hand using a waste cloth.
    2. Take care not to splash ATF when applying the air.



    D026713E02
  1. Remove the 2 O-rings from the 1st and reverse brake piston.



83. REMOVE COUNTER DRIVE GEAR


    C134861E01
  1. Using SST and a press, remove the counter drive gear from the transaxle case.

    SST
    09950-60010   (09951-00590)
    09950-70010   (09951-07100)



    D003602E01
  1. Tighten the 2 bolts evenly and make clearance of approx. 20.0 mm (0.797 in.) between the counter drive gear and the inner race.



    C134858E01
  1. Using SST, remove the tapered roller bearing inner race.

    SST
    09950-00020  
    09950-00030  
    09950-60010   (09951-00590)



84. REMOVE COUNTER DRIVE ANGULAR BALL BEARING


    C134859E01
  1. Remove the bearing inner race (rear side) and angular ball (rear side).



    C134860E01
  1. Using SST, remove the bearing outer race (rear side) from the transaxle case.

    SST
    09308-00010  



    C134925
  1. Remove the angular ball (front side).



    C134862E01
  1. Using SST and a press, remove the bearing outer race (front side) from the transaxle case.

    SST
    09950-60020   (09951-00810)
    09950-70010   (09951-07200)



    C134863
  1. Using a screwdriver, remove the snap ring from the transaxle case.



85. REMOVE UNDERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY


    D026407E01
  1. Place SST on the return spring, and compress the return spring with a press.

    SST
    09387-00020  

  1. Using a snap ring expander, remove the snap ring.

    NOTICE:
    1. Stop the press when the spring seat is lowered to the place 1 to 2 mm (0.039 to 0.078 in.) from the snap ring groove to prevent the spring seat from being deformed.
    2. Do not expand the snap ring excessively.

  1. Remove the return spring.



86. INSPECT UNDERDRIVE BRAKE RETURN SPRING SUB-ASSEMBLY


    C141534
  1. Using vernier calipers, measure the free length of the spring together with the spring seat.

    Standard free length:
    13.24 mm (0.5213 in.)

    If the free length is shorter than the standard free length, replace the under drive brake return spring sub-assembly.



87. REMOVE UNDERDRIVE BRAKE PISTON


    D026406E02
  1. Apply compressed air (392 kPa, 4.0 kgf/cm2, 57 psi) to the transaxle case to remove the underdrive brake piston.



    D003794E03
  1. Remove the 2 O-rings from the underdrive brake piston.



88. REMOVE NEEDLE ROLLER BEARING


    D003605E03
  1. Using SST, remove the needle roller bearing from the transaxle case.

    SST
    09387-00041   (09387-01010, 09387-01030, 09387-01040)



89. REMOVE UNDERDRIVE CLUTCH DRUM OIL SEAL RING


    D003914E05
  1. Remove the 2 oil seal rings from the transaxle case.



90. REMOVE NO. 1 TRANSAXLE CASE PLUG


    D026383
  1. Remove the 2 No. 1 transaxle case plugs.

  1. Remove the 2 O-rings from the 2 No. 1 transaxle case plugs.



91. REMOVE UNDERDRIVE CYLINDRICAL ROLLER BEARING


    C134864E01
  1. Using SST, remove the underdrive cylindrical roller bearing from the transaxle case.

    SST
    09820-00031  
    09950-40011   (09952-04010, 09954-04010, 09955-04061, 09957-04010)
    09950-50013   (09951-05010, 09953-05020)



92. REMOVE UNDERDRIVE OUTPUT SHAFT OIL SEAL RING


    D003915E08
  1. Remove the oil seal ring from the transaxle housing.



93. REMOVE DIFFERENTIAL GEAR LUBE APPLY TUBE


    C134866E01
  1. Remove the bolt, transaxle apply tube clamp and differential gear lube apply tube from the transaxle housing.