Home › TRANSMISSION ยท U250E AUTOMATIC TRANSAXLE › OIL PUMP

OIL PUMP > DISASSEMBLY

for Preparation Click here



1. INSPECT OIL PUMP ASSEMBLY


    C134883
  1. Turn the drive gear with 2 screwdrivers and make sure that it rotates smoothly.

    NOTICE:
    Be careful not to damage the oil seal lip.



2. REMOVE CLUTCH DRUM OIL SEAL RING


    D003650E01
  1. Remove the 2 clutch drum oil seal rings.



3. REMOVE STATOR SHAFT ASSEMBLY


    D003651E01
  1. Using a torx socket (T30), remove the 11 bolts and stator shaft.

  1. Keep the gears in assembling order.



4. INSPECT CLEARANCE OF OIL PUMP ASSEMBLY


    D009207E01
  1. Push the driven gear to one side of the body.

  1. Using a feeler gauge, measure the clearance.

    Standard body clearance:
    0.10 to 0.17 mm (0.0039 to 0.0067 in.)

    Side clearance:
    0.02 to 0.05 mm (0.001 to 0.002 in.)

    Maximum body clearance:
    0.17 mm (0.0067 in.)

    If the body clearance is greater than the maximum, replace the oil pump body sub-assembly.



    D009208
  1. Using a feeler gauge, measure the tip clearance between the driven gear teeth and drive gear teeth.

    Standard tip clearance:
    0.07 to 0.15 mm (0.0028 to 0.0059 in.)
    Maximum tip clearance:
    0.15 mm (0.0059 in.)

    If the tip clearance is greater than the maximum, replace the oil pump body sub-assembly.



    D009209
  1. Using a straight edge and feeler gauge, measure the side clearance of both gears.

    Standard side clearance:
    0.02 to 0.05 mm (0.0008 to 0.0020 in.)
    Maximum side clearance:
    0.05 mm (0.0020 in.)

    Drive gear thickness: mm (in.) 
    Mark
    Thickness
    A
    11.690 to 11.699 (0.4602 to 0.4606)
    B
    11.700 to 11.709 (0.4606 to 0.4610)
    C
    11.710 to 11.720 (0.4610 to 0.4614)
    D
    11.721 to 11.730 (0.4615 to 0.4618)
    E
    11.731 to 11.740 (0.4619 to 0.4622)
    Driven gear thickness: mm (in.) 
    Mark
    Thickness
    A
    11.690 to 11.699 (0.4602 to 0.4606)
    B
    11.700 to 11.709 (0.4606 to 0.4610)
    C
    11.710 to 11.720 (0.4610 to 0.4614)
    D
    11.721 to 11.730 (0.4615 to 0.4618)
    E
    11.731 to 11.740 (0.4619 to 0.4622)



5. REMOVE FRONT OIL PUMP DRIVE GEAR


    D009206E02
  1. Remove the front oil pump drive gear.



6. REMOVE FRONT OIL PUMP DRIVEN GEAR


    D009206E01
  1. Remove the front oil pump driven gear.



7. REMOVE FRONT OIL PUMP BODY O-RING


    D025586E03
  1. Using a screwdriver, remove the O-ring.

    HINT:
    Tape the screwdriver tip before use.



8. REMOVE FRONT OIL PUMP OIL SEAL


    D003647E01
  1. Mount the oil pump in a soft jaw vise.

  1. Using SST, remove the oil seal from the oil pump body.

    SST
    09308-00010