Home › TRANSMISSION · E351 MANUAL TRANSAXLE › MANUAL TRANSAXLE UNIT

MANUAL TRANSAXLE UNIT > DISASSEMBLY

for Preparation Click here



1. REMOVE CLUTCH RELEASE FORK SUB-ASSEMBLY


    C069774
  1. Remove the clutch release fork sub-assembly together with the clutch release bearing assembly from the manual transaxle case.



2. REMOVE CLUTCH RELEASE BEARING ASSEMBLY
  1. Remove the clutch release bearing assembly and release bearing hub clip from the clutch release fork sub-assembly.



3. REMOVE RELEASE FORK SUPPORT


    C083809
  1. Remove the release fork support from the manual transaxle case.



4. REMOVE CLUTCH RELEASE FORK BOOT
  1. Remove the clutch release fork boot from the manual transaxle case.



5. REMOVE SPEEDOMETER DRIVEN HOLE COVER SUB-ASSEMBLY
  1. Remove the bolt and speedometer driven hole cover sub-assembly.

  1. Remove the O-ring.



6. REMOVE SELECTING BELLCRANK ASSEMBLY


    C138359
  1. Remove the 2 bolts and selecting bellcrank assembly from the manual transmission case.



7. REMOVE CONTROL SHIFT LEVER


    C138360
  1. Remove the nut and spring washer.



    C138361
  1. Using a brass bar and hammer, remove the shift outer lever lock pin.

  1. Remove the control shift lever.



8. REMOVE CONTROL SHAFT COVER


    C092834
  1. Remove the 4 bolts and control shaft cover from the manual transmission case.



9. SECURE MANUAL TRANSAXLE ASSEMBLY


    C087963
  1. Place the manual transaxle assembly on wooden blocks.



10. REMOVE NO. 1 LOCK BALL ASSEMBLY


    C138362
  1. Remove the No. 1 lock ball assembly from the manual transmission case.



11. REMOVE SHIFT GATE PIN


    C138363
  1. Remove the shift gate pin from the manual transmission case.



12. REMOVE MANUAL TRANSMISSION BREATHER PLUG


    C138364
  1. Remove the manual transmission breather plug.



13. REMOVE SHIFT AND SELECT LEVER SHAFT ASSEMBLY


    C138371
  1. Remove the shift and select lever shaft assembly from the manual transmission case.



14. REMOVE BACK-UP LIGHT SWITCH ASSEMBLY


    C087966
  1. Remove the back-up light switch assembly and gasket from the manual transmission case.



15. REMOVE MANUAL TRANSMISSION FILLER PLUG


    C070824
  1. Remove the manual transmission filler plug and gasket from the manual transmission case.



16. REMOVE DRAIN PLUG SUB-ASSEMBLY


    C087967
  1. Remove the drain plug sub-assembly and gasket from the manual transmission case.



17. REMOVE MANUAL TRANSMISSION CASE COVER SUB-ASSEMBLY


    D031904
  1. Remove the 10 bolts and manual transmission case cover from the manual transmission case.



18. REMOVE MANUAL TRANSMISSION OUTPUT SHAFT REAR SET NUT


    C069266
  1. Engage the 1st and 2nd gears simultaneously.



    C087968E02
  1. Using SST and a hammer, unstake the manual transmission output shaft rear set nut.

    SST
    09930-00010  



    C087969E02
  1. Using SST, remove the manual transmission output shaft rear set nut from the output shaft.

    SST
    09229-55010  

  1. Disengage the gears.



19. REMOVE NO. 3 TRANSMISSION CLUTCH HUB


    C069269
  1. Using 2 screwdrivers and a hammer, remove the transmission clutch hub No. 3 shaft snap ring from the input shaft.

    HINT:
    Use a shop rag or a piece of cloth to keep the snap ring from flying.



    C069270
  1. Remove the shift fork set bolt from the No. 3 gear shift fork.



    C069777E02
  1. Using SST, remove the No. 3 transmission clutch hub and No. 3 gear shift fork from the input shaft.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010)
    09950-50013   (09957-04010)
    09950-60010   (09951-00280)



20. REMOVE 5TH GEAR


    C069454
  1. Remove the 5th gear from the input shaft.



21. REMOVE 5TH GEAR NEEDLE ROLLER BEARING


    C069455
  1. Remove the 5th gear needle roller bearing from the input shaft.



22. REMOVE 5TH DRIVEN GEAR


    C069456E02
  1. Using SST, remove the 5th driven gear from the output shaft.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09957-04010)
    09950-60010   (09951-00180, 09955-03011)
    09950-50013  



23. REMOVE REAR BEARING RETAINER


    C069457E01
  1. Using a "TORX" socket wrench (T45), remove the 7 "TORX" screws and rear bearing retainer from the manual transmission case.



24. REMOVE OUTPUT SHAFT REAR BEARING SHIM


    C069458
  1. Remove the output shaft rear bearing shim from the output shaft.



25. REMOVE INPUT SHAFT REAR BEARING SHAFT SNAP RING


    C087970
  1. Using a snap ring expander, remove the input shaft rear bearing shaft snap ring from the input shaft.



26. REMOVE SHIFT FORK SHAFT SHAFT SNAP RING


    C087971
  1. Using 2 screwdrivers and a hammer, remove the shift fork shaft shaft snap ring from the No. 1 gear shift fork shaft.

    HINT:
    Use a shop rag or a piece of cloth to keep the snap ring from flying.



    C069460
  1. Using 2 screwdrivers and a hammer, remove the shift fork shaft shaft snap ring from the No. 2 gear shift fork shaft.

    HINT:
    Use a shop rag or a piece of cloth to keep the snap ring from flying.



27. REMOVE REVERSE IDLER GEAR SHAFT BOLT


    C083225
  1. Remove the reverse idler gear shaft bolt and gasket.



28. REMOVE NO. 1 CLUTCH TUBE BRACKET
  1. Remove the bolt and clutch tube bracket.



29. REMOVE MANUAL TRANSMISSION CASE


    C083226
  1. Remove the 3 bolts from the manual transaxle case.



    C083227
  1. Remove the 14 bolts from the manual transmission case.

  1. Tapping with a plastic hammer, remove the manual transmission case.



30. REMOVE REVERSE RESTRICT PIN ASSEMBLY


    C135409
  1. Using a hexagon wrench (6 mm), remove the reverse restrict pin plug from the manual transmission case.



    C135410
  1. Using a pin punch (φ 5 mm) and hammer, remove the slotted pin.



    C135411
  1. Remove the bolt, transmission oil baffle and reverse restrict pin assembly.



31. REMOVE NO. 2 OIL RECEIVER PIPE


    C138376
  1. Remove the bolt and No. 2 oil receiver pipe from the manual transmission case.

    NOTICE:
    Do not damage the pipe.



32. REMOVE NO. 1 OIL RECEIVER PIPE


    C138375
  1. Remove the bolt and No. 1 oil receiver pipe from the manual transmission case.

    NOTICE:
    Do not damage the pipe.



33. REMOVE TRANSMISSION MAGNET


    C069468
  1. Remove the transmission magnet from the manual transaxle case.



34. REMOVE REVERSE IDLER GEAR SUB-ASSEMBLY


    C069470
  1. Remove the reverse idler gear sub-assembly from the manual transaxle case.



    C070512
  1. Remove the reverse gear and reverse idler thrust washer from the reverse idler gear shaft.



35. REMOVE REVERSE SHIFT ARM BRACKET ASSEMBLY


    C083230
  1. Remove the 2 bolts and reverse shift arm bracket assembly from the manual transaxle case.



36. REMOVE NO. 1 GEAR SHIFT FORK SHAFT


    C083231
  1. Remove the shift fork set bolt from the No. 1 gear shift fork.



    C087975
  1. Pull out the No. 1 gear shift fork shaft while the No. 3 gear shift fork shaft is pulled up.



    C069500
  1. Using 2 screwdrivers and a hammer, remove the shift fork shaft snap ring from the No. 1 gear shift fork shaft.

    HINT:
    Use a shop rag or a piece of cloth to keep the snap ring from flying.



37. REMOVE REVERSE SHIFT FORK ROLLER


    C083233
  1. Using a magnetic finger, remove the reverse shift fork roller from the reverse shift fork.



38. REMOVE NO. 2 GEAR SHIFT FORK SHAFT


    C083234
  1. Remove the shift fork set bolt and shift head set bolt from the No. 2 gear shift fork and No. 1 gear shift head.



    C087976E07
  1. Remove the No. 2 gear shift fork shaft and No. 1 gear shift head from the manual transaxle case.



39. REMOVE NO. 1 GEAR SHIFT FORK


    C087977E05
  1. Remove the No. 1 gear shift fork.



40. REMOVE NO. 3 GEAR SHIFT FORK SHAFT


    C087978E05
  1. Remove the No. 3 gear shift fork shaft from the manual transaxle case.



    C083238
  1. Using 2 screwdrivers and a hammer, remove the 2 shift fork shaft snap rings from the No. 3 gear shift fork shaft.

  1. Remove the reverse shift fork from the No. 3 gear shift fork shaft.



41. REMOVE NO. 2 GEAR SHIFT FORK


    C087979E05
  1. Remove the No. 2 gear shift fork from the input shaft assembly.



42. REMOVE INPUT SHAFT ASSEMBLY


    C083240
  1. Tilt the output shaft, then remove the input shaft from the manual transaxle case.



43. REMOVE OUTPUT SHAFT ASSEMBLY


    C083241E03
  1. Lift the differential case assembly with the output shaft assembly leaned.

  1. Remove the output shaft assembly from the manual transaxle case.



44. REMOVE DIFFERENTIAL CASE ASSEMBLY


    C083242
  1. Remove the differential case assembly from the manual transaxle case.



45. REMOVE MANUAL TRANSAXLE CASE RECEIVER


    C083243
  1. Remove the 3 bolts and manual transaxle case receiver from the manual transaxle case.



46. REMOVE INPUT SHAFT FRONT BEARING


    C087980E02
  1. Using SST, remove the input shaft front bearing (outer race) from the manual transaxle case.

    SST
    09612-65014   (09612-01040, 09612-01050)



47. REMOVE FRONT TRANSAXLE CASE OIL SEAL


    C087981E02
  1. Using SST, remove the manual transaxle case oil seal from the manual transaxle case.

    SST
    09612-65014   (09612-01040, 09612-01050)



48. REMOVE OUTPUT SHAFT FRONT BEARING


    C087982E02
  1. Using SST, remove the output shaft front bearing (outer race) from the manual transaxle case.

    SST
    09387-00041   (09387-02020, 09387-02010)



49. REMOVE OUTPUT SHAFT COVER


    C069483
  1. Remove the output shaft cover from the manual transaxle case.



50. REMOVE OUTPUT SHAFT REAR BEARING


    C087983E02
  1. Using SST and a hammer, remove the output shaft rear bearing from the manual transmission case (outer race).

    SST
    09950-60010   (09951-00680)
    09950-70010   (09951-07100)



51. REMOVE TRANSMISSION CASE OIL SEAL


    C087984E02
  1. Using SST, remove the transmission case oil seal from the manual transmission case.

    SST
    09308-00010  



52. REMOVE FRONT TRANSAXLE CASE COVER OIL SEAL


    D032768
  1. Using a screwdriver, remove the front transaxle case cover oil seal.

    HINT:
    Tape the screwdriver tip before use to avoid damage.



53. REMOVE FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING


    C069490
  1. Using a brass bar and a hammer, remove the front differential case front tapered roller bearing (outer race) from the manual transaxle case.



    C070822E04
  1. Using SST, remove the front differential case front tapered roller bearing from the front differential case.

    SST
    09950-00020  
    09950-00030  
    09950-40011   (09957-04010)
    09950-60010   (09951-00560)



54. REMOVE FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING


    C087986E02
  1. Using SST and a hammer, remove the front differential case rear tapered roller bearing (outer race) and front differential case rear shim from the manual transmission case.

    SST
    09950-60020   (09951-00790)
    09950-70010   (09951-07100)



    C090344E04
  1. Using SST, remove the front differential case rear tapered roller bearing (inner race) from the front differential case.

    SST
    09950-60020  
    09950-00030  
    09950-40011   (09957-04010)
    09950-60010   (09951-00490)



55. REMOVE NO. 3 TRANSMISSION HUB SLEEVE


    C087988E04
  1. Remove the No. 3 transmission hub sleeve from the No. 3 transmission clutch hub.



56. REMOVE NO. 3 SYNCHROMESH SHIFTING KEY SPRING


    C069507
  1. Remove the 2 No. 3 synchromesh shifting key springs from the No. 3 transmission clutch hub while pushing on the No. 3 synchromesh shifting key spring.



57. REMOVE SYNCHRONIZER PULL RING


    C069508
  1. Using a screwdriver, remove the synchronizer pull ring snap ring.

  1. Remove the synchronizer pull ring, No. 5 synchronizer outer ring, No. 5 synchronizer inner ring, and No. 5 synchronizer ring middle from the No. 5 synchronizer ring inner.