Home › TRANSMISSION ยท E351 MANUAL TRANSAXLE › INPUT SHAFT

INPUT SHAFT > REASSEMBLY

for Preparation Click here



1. INSTALL INPUT SHAFT FRONT BEARING


    C092871E02
  1. Using SST and a press, install the input shaft front bearing (inner race).

    SST
    09608-00071  



2. INSTALL NO. 2 TRANSMISSION HUB SLEEVE


    D031909E01
  1. Coat the transmission No. 2 hub sleeve with gear oil.

  1. Install the 3 synchromesh key springs with the No. 2 transmission hub sleeve.

    NOTICE:
    Install the No. 2 transmission clutch hub sleeve and the No. 2 transmission clutch hub in the correct direction.

  1. Using a screwdriver, install the synchromesh shifting key to the input shaft.



3. INSTALL 3RD GEAR NEEDLE ROLLER BEARING


    C069617
  1. Coat the 3rd gear bearing with gear oil and install it to the input shaft.



4. INSTALL 3RD GEAR


    C069629
  1. Coat the 3rd gear with gear oil and install it to the input shaft.



5. INSTALL NO. 3 SYNCHRONIZER RING


    C069630
  1. Coat the No. 3 synchronizer ring with gear oil and install it to the 3rd gear.



6. INSTALL NO. 2 TRANSMISSION CLUTCH HUB


    C092872E02
  1. Using SST and a press, install the No. 2 transmission clutch hub to the input shaft.

    SST
    09316-60011   (09316-00041)

    NOTICE:
    1. Align the claw of the clutch hub No. 2 with the notch of the synchronizer ring No. 3.
    2. Make sure that the 3rd gear can rotate.



    D031916
  1. Select a snap ring so that clearance between the No. 2 transmission clutch hub and the No. 2 clutch hub shaft snap ring will be within the specified range. Using a brass bar and a hammer, install the snap ring.

    Standard clearance:
    0.1 mm or less (0.0039 in.) or less

    Snap ring thickness:
    Part No.
    Thickness: mm (in.)
    Mark
    90520-34003
    2.30 to 2.35
    (0.0906 to 0.0925)
    H
    90520-34004
    2.35 to 2.40
    (0.0925 to 0.0945)
    J
    90520-34005
    2.40 to 2.45
    (0.0945 to 0.0965)
    K
    90520-34006
    2.45 to 2.50
    (0.0965 to 0.0984)
    L
    90520-34007
    2.50 to 2.55
    (0.0984 to 0.1004)
    M
    90520-34008
    2.55 to 2.60
    (0.1004 to 0.1024)
    N
    90520-34009
    2.60 to 2.65
    (0.1024 to 0.1043)
    P



7. INSTALL 4TH GEAR BEARING SPACER


    D031906
  1. Coat the 4th gear bearing spacer with gear oil and install it to the input shaft.



8. INSTALL 2ND SYNCHRONIZER OUTER RING


    D031907
  1. Coat the 2nd synchronizer outer ring (No. 4 synchronizer ring) with gear oil and install it to the No. 2 transmission clutch hub.

    NOTICE:
    Align the claw of the No. 2 clutch hub with the notch of the 2nd synchronizer outer ring (No. 4 synchronizer ring).



9. INSTALL 4TH GEAR NEEDLE ROLLER BEARING


    C069551
  1. Coat the 4th gear needle roller bearing with gear oil and install it to the input shaft.



10. INSTALL 4TH GEAR


    C069633
  1. Coat the 4th gear with gear oil and install it to the input shaft.



11. INSTALL INPUT SHAFT REAR RADIAL BALL BEARING


    C092857E01
  1. Using SST and a press, install the input shaft rear radial ball bearing to the input shaft.

    SST
    09608-06041  

    NOTICE:
    1. Install the bearing with its groove facing rearward.
    2. Make sure that the 3rd gear rotates.



    C069635
  1. Select a snap ring so that the clearance between the input shaft radial ball rear bearing and the input shaft rear bearing snap ring will be within the specified range. Using a brass bar and a hammer, install the snap ring.

    Standard clearance:
    0.1 mm (0.004 in.) or less

    Snap ring:
    Part No.
    Thickness: mm (in.)
    Mark
    90520-30008
    2.35 to 2.40
    (0.0925 to 0.0945)
    1
    90520-30009
    2.40 to 2.45
    (0.0945 to 0.0965)
    2
    90520-30010
    2.45 to 2.50
    (0.0965 to 0.0984)
    3
    90520-30011
    2.50 to 2.55
    (0.0984 to 0.1004)
    4
    90520-30012
    2.55 to 2.60
    (0.1004 to 0.1024)
    5
    90520-30013
    2.60 to 2.65
    (0.1024 to 0.1043)
    6
    90520-30021
    2.65 to 2.70
    (0.1043 to 0.1063)
    7
    90520-30022
    2.70 to 2.75
    (0.1063 to 0.1083)
    8