Home › TRANSMISSION ยท E351 MANUAL TRANSAXLE › OUTPUT SHAFT

OUTPUT SHAFT > REASSEMBLY

for Preparation Click here



1. INSTALL REVERSE GEAR


    C069672
  1. Coat the reverse gear with gear oil.

  1. Install the 3 No. 1 synchromesh shifting key springs and No. 1 transmission clutch hub to the reverse gear.

    NOTICE:
    Assemble the reverse gear and the No. 1 transmission clutch hub in the correct direction.

  1. Using a screwdriver, install the 3 No. 1 synchromesh shifting keys to the reverse gear.



2. INSTALL OUTPUT SHAFT FRONT BEARING


    C092874E02
  1. Using SST and a press, install the output shaft front bearing (inner race) to the output shaft.

    SST
    09950-60010   (09951-00430)
    09950-70010   (09951-07150)



3. INSTALL NO. 1 SYNCHRONIZER RING SET


    C069649
  1. Coat the No. 1 synchronizer ring set with gear oil and install it to the 1st gear.

    NOTICE:
    Align the No. 1 synchronizer ring set with the hole of the 1st gear.



4. INSTALL 1ST GEAR NEEDLE ROLLER BEARING


    C069650
  1. Coat the 1st gear needle roller bearing with gear oil and install it to the output shaft.



5. INSTALL 1ST GEAR


    C069673
  1. Coat the 1st gear with gear oil and install it to the output shaft.



6. INSTALL NO. 1 TRANSMISSION CLUTCH HUB


    C092862E02
  1. Using SST and a press, install the No. 1 transmission clutch hub to the output shaft.

    SST
    09316-60011   (09316-00031)
    09950-60010   (09951-00320)
    09950-70010   (09951-07100)

    NOTICE:
    1. Align the No. 1 synchronizer ring with the No. 1 synchromesh shifting key.
    2. Make sure that the 1st gear rotates.



7. INSTALL 2ND GEAR BUSHING BALL


    C083814
  1. Coat the gear bushing with MP grease, and install it to the output shaft.



8. INSTALL 2ND GEAR BUSHING


    C069646
  1. Coat the 2nd gear bushing with gear oil and install it to the output shaft.



9. INSTALL 2ND GEAR BEARING SPACER


    C069645
  1. Coat the 2nd gear bearing spacer with gear oil and install it to the output shaft.



10. INSTALL 2ND GEAR NEEDLE ROLLER BEARING


    C069644
  1. Coat the 2nd gear needle roller bearing with gear oil and install it to the output shaft.



11. INSTALL NO. 2 SYNCHRONIZER RING SET


    C069643
  1. Coat the No. 2 synchronizer ring set with gear oil and install it to the No. 1 transmission clutch hub.

    NOTICE:
    Align the key groove on the No. 2 synchronizer ring set with the No. 1 synchromesh shifting key.



12. INSTALL 2ND GEAR


    C069679
  1. Coat the 2nd gear with gear oil and install it to the output shaft.



13. INSTALL 3RD DRIVEN GEAR


    C092863E02
  1. Using SST and a press, install the 3rd driven gear to the output shaft.

    SST
    09608-00071  
    09950-60010   (09951-00320)
    09950-70010   (09951-07100)



14. INSTALL OUTPUT GEAR SPACER


    C069641
  1. Install the output gear spacer to the output shaft.



15. INSTALL 4TH DRIVEN GEAR


    C092864E03
  1. Using SST and a press, install the 4th driven gear to the output shaft.

    SST
    09608-00071  
    09950-60010   (09951-00320)
    09950-70010   (09951-07100)



16. INSTALL OUTPUT SHAFT FRONT BEARING


    C092865E02
  1. Using SST and a press, install the output shaft front bearing (inner race) to the output shaft.

    SST
    09506-30012  
    09950-60010   (09951-00320)
    09950-70010   (09951-07100)