SFI SYSTEM > Fuel Injector Circuit |

| 1.INSPECT ECM (#10, #20, #30, #40 VOLTAGE) |
![]() |
Disconnect the C24 ECM connector.
Turn the ignition switch to the ON position.
Measure the voltage between the terminals of the ECM connector.
| Tester Connection | Specified Condition |
| #10 (C24-108) - Body ground | 9 to 14 V |
| #20 (C24-107) - Body ground | |
| #30 (C24-106) - Body ground | |
| #40 (C24-105) - Body ground |
Reconnect the ECM connector.
|
| ||||
| NG | |
| 2.INSPECT FUEL INJECTOR (RESISTANCE) |
Inspect the fuel injector .
|
| ||||
| OK | |
| 3.CHECK HARNESS AND CONNECTOR |
![]() |
Disconnect the C7 to C10 injector connectors.
Turn the ignition switch to the ON position.
Measure the voltage.
| Cylinder | Tester Connection | Specified Condition |
| No. 1 | C7-1 - Body ground | 11 to 14 V |
| No. 2 | C9-1 - Body ground | |
| No. 3 | C8-1 - Body ground | |
| No. 4 | C10-1 - Body ground |
| Result | Proceed to |
| NG (RHD) | A |
| NG (LHD) | B |
| OK | C |
Reconnect the injector connectors.
|
| ||||
|
| ||||
| A | |
| 4.INSPECT IGNITION RELAY NO. 2 |
![]() |
Remove the IG2 relay from the engine room R/B.
Measure the resistance between the terminals.
| Tester Connection | Specified Condition |
| 3 - 5 | 10 kΩ or higher |
| Below 1 Ω (Apply battery voltage between terminals 1 and 2) |
Reinstall the IG2 relay.
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (IG2 RELAY - BODY GROUND) |
![]() |
Remove the IG2 relay from the engine room R/B.
Measure the resistance between the terminals.
| Tester Connection | Specified Condition |
| IG2 relay terminal 2 - Body ground | Below 1 Ω |
Reinstall the IG2 relay.
|
| ||||
| NG | ||
| ||
| 6.INSPECT FUSE (INJ FUSE) |
![]() |
Remove the INJ fuse from the instrument panel J/B.
Measure the fuse resistance.
Reinstall the fuse.
|
| ||||
| OK | |
| 7.INSPECT IGNITION SWITCH |
![]() |
Disconnect the E23 ignition switch connector.
Measure the resistance between the terminals.
| Tester Connection | Ignition Switch Position | Specified Condition |
| All Terminals | LOCK | 10 kΩ or higher |
| 2 - 4 | ACC | Below 1 Ω |
| 1 - 2 - 4, 5 - 6 | ON | |
| 1 - 3 - 4, 5 - 6 - 7 | START |
Reconnect the ignition switch connector.
|
| ||||
| OK | ||
| ||
| 8.CHECK HARNESS AND CONNECTOR (INJECTOR - ECM) |
![]() |
Disconnect the C7 to C10 injector connectors.
Disconnect the C24 ECM connector.
Measure the resistance between the injector and the ECM connector terminals.
| Cylinder | Tester Connection | Specified Condition |
| No. 1 | C7-2 or #10 (C24-108) - Body ground | 10 kΩ or higher |
| C7-2 - #10 (C24-108) | Below 1 Ω | |
| No. 2 | C9-2 or #20 (C24-107) - Body ground | 10 kΩ or higher |
| C9-2 - #20 (C24-107) | Below 1 Ω | |
| No. 3 | C8-2 or #30 (C24-106) - Body ground | 10 kΩ or higher |
| C8-2 - #30 (C24-106) | Below 1 Ω | |
| No. 4 | C10-2 or #40 (C24-105) - Body ground | 10 kΩ or higher |
| C10-2 - #40 (C24-105) | Below 1 Ω |
Reconnect the injector connectors.
Reconnect the ECM connector.
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND) |
![]() |
Disconnect the C24 ECM connector.
Measure the resistance.
| Tester Connection | Specified Condition |
| E01 (C24-45) - Body ground | Below 1 Ω |
| E02 (C24-44) - Body ground | Below 1 Ω |
Reconnect the ECM connector.
|
| ||||
| OK | |
| 10.INSPECT FUEL INJECTOR (FUEL INJECTION VOLUME) |
Inspect the fuel injector .
|
| ||||
| OK | ||
| ||