Home › BODY ELECTRICAL › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM

POWER DOOR LOCK CONTROL SYSTEM > Door Control Switch Circuit

for Preparation Click here


DESCRIPTION

When the lock side of the door control switch is pressed, continuity is established between terminal 2 (LHD) or 2 (RHD) and terminal 1 (LHD) or 9 (RHD) of the switch. When the unlock side of the switch is pressed, continuity is established between terminal 9 (LHD), 8 (RHD) and 1 (LHD) or 9 (RHD).
Terminals L1 and UL1 of the main body ECU are connected to the door control switch and door lock/unlock request signals (by door control switch operation) are input to the ECU.
The main body ECU constantly applies voltage to terminal 2 (LHD) or 2 (RHD) of the door control switch via terminal L1. When the door control switch is operated to lock all doors, current flows from terminal L1 to terminal 2 (LHD) or 2 (RHD). The main body ECU determines that this is door lock request signal input.
The main body ECU also applies constant voltage to terminal 9 (LHD) or 2 (RHD) of the door control switch via terminal UL1. When the door control switch is operated to unlock the doors, current flows from terminal UL1 to terminal 9 (LHD) or 2 (RHD). The main body ECU determines that this is door unlock request signal input.

WIRING DIAGRAM


B109774E13


B109774E14


INSPECTION PROCEDURE

1.INSPECT DOOR CONTROL SWITCH ASSEMBLY


    E123893E04
  1. Remove the master switch.

  1. Measure the resistance of the door control switch.

    Standard resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    (*1) 2 - 1
    Lock
    Below 1 Ω
    (*1) 2 - 1
    OFF (Free)
    10 kΩ or higher
    (*1) 9 - 1
    Unlock
    Below 1 Ω
    (*1) 9 - 1
    OFF (Free)
    10 kΩ or higher
    (*2) 2 - 9
    Lock
    Below 1 Ω
    (*2) 2 - 9
    OFF (Free)
    10 kΩ or higher
    (*2) 8 - 9
    Unlock
    Below 1 Ω
    (*2) 8 - 9
    OFF (Free)
    10 kΩ or higher

    *1: LHD
    *2: RHD



NG
REPLACE DOOR CONTROL SWITCH OR MASTER SWITCH
OK


2.CHECK WIRE HARNESS (DOOR CONTROL SWITCH - MAIN BODY ECU (INSTRUMENT PANEL J/B))


  1. Disconnect the door control switch connector.


    B138033E01

  1. Disconnect the ECU (instrument panel J/B) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    (*1) M1-2 - IK-15
    Always
    Below 1 Ω
    (*1) M1-9 - IK-12
    Always
    Below 1 Ω
    (*1) M1-1 - Body ground
    Always
    Below 1 Ω
    (*1) IK-15 - Body ground
    Always
    10 kΩ or higher
    (*1) IK-12 - Body ground
    Always
    10 kΩ or higher
    (*2) L1-2 - IJ-3
    Always
    Below 1 Ω
    (*2) L1-8 - IJ-4
    Always
    Below 1 Ω
    (*2) L1-9 - Body ground
    Always
    Below 1 Ω
    (*2) IJ-3 - Body ground
    Always
    10 kΩ or higher
    (*2) IJ-4 - Body ground
    Always
    10 kΩ or higher

    *1: LHD
    *2: RHD



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE