FRONT WHEEL ALIGNMENT > ADJUSTMENT |
| 1. INSPECT TIRES |
Check the tires for wear and proper inflation pressure.
| Tire size | Front kPa (kgf*cm2, psi) | Rear kPa (kgf*cm2, psi) | |
| 215/60R16 95V | 4 passengers or less | 250 (2.5, 36)*1, 230 (2.3, 33)*2, 210 (2.1, 31)*3
| 250 (2.5, 36)*1, 230 (2.3, 33)*2, 210 (2.1, 31)*3
|
| 5 passengers | 270 (2.8, 39)*1, 250 (2.5, 36)*2, 220 (2.2, 32)*3
| 270 (2.8, 39)*1, 250 (2.5, 36)*2, 220 (2.2, 32)*3
| |
![]() |
Using a dial indicator, check the runout of the tires.
| 2. MEASURE VEHICLE HEIGHT |
![]() |
Bounce the vehicle up and down at the corners to stabilize the suspension. Inspect the vehicle height.
| Engine | Transaxle | Front A - B | Rear C - D |
| 2AZ-FE | Automatic | 115 mm (4.53 in.) | 38 mm (1.50 in.) |
| 2AZ-FE | Manual | 116 mm (4.57 in.) | 39 mm (1.53 in.) |
| 2GR-FE | Automatic | 117 mm (4.61 in.) | 42 mm (1.65 in.) |
| 3. INSPECT TOE-IN |
Bounce the vehicle up and down at the corners to stabilize the suspension.
Release the parking brake and move the shift lever to the neutral position.
Push the vehicle straight ahead approximately 5 m (16.4 ft). (*1)
![]() |
Put tread center marks on the rearmost points of the front wheels and measure the distance between the marks (dimension B).
Slowly push the vehicle straight ahead to cause the front wheels to rotate 180° using the front tire valve as a reference point.
![]() |
Measure the distance between the tread center marks on the front side of the wheels.
| Toe-in (total) | - |
| A - B: | 0 +/- 2 mm (0 +/- 0.08 in.) |
| 4. ADJUST TOE-IN |
![]() |
Measure the thread lengths of the right and left rack ends.
Remove the rack boot set clips.
Loosen the tie rod end lock nuts.
Adjust the rack ends if the difference in thread length between the right and left rack ends is not within the specified range.
Extend the shorter rack end if the measured toe-in deviates toward the outside.
Shorten the longer rack end if the measured toe-in deviates toward the inside.
Turn the right and left rack ends by equal amounts to adjust the toe-in.
Make sure that the lengths of the right and left rack ends are the same.
Tighten the tie rod end lock nuts.
Place the boots on the seats and install the clips.
| 5. INSPECT WHEEL ANGLE |
Put tread center marks on the rearmost points of the turning radius gauge.
![]() |
Turn the steering wheel fully to the left and right and measure the turning angle.
| Inside wheel | Outside wheel reference |
| 38°42' +/- 2°(38.70°+/- 2°) | 33°46' (33.77°) |
| 6. INSPECT CAMBER, CASTER AND STEERING AXIS INCLINATION |
![]() |
Put the front wheel on the center of the alignment tester.
Remove the center ornament.
Set the camber-caster-king pin gauge and attachment at the center of the axle hub or drive shaft.
Inspect the camber, caster and steering axis inclination.
| Camber | Right-left difference |
| -0°30' +/- 45' (-0.50°+/- 0.75°) | 45' (0.75°) or less |
| Caster | Right-left difference |
| 2°40' +/- 45' (2.67°+/- 0.75°) | 45' (0.75°) or less |
| Steering axis inclination | Right-left difference |
| 12°00' +/- 45' (12.00°+/- 0.75°) | 45' (0.75°) or less |
Remove the camber-caster-king pin gauge and attachment.
Install the center ornament.
If the caster and steering axis inclination are not within the specified range after the camber has been correctly adjusted, recheck the suspension parts for damage and/or wear.
| 7. ADJUST CAMBER |
Remove the front wheel.
![]() |
Remove the 2 nuts on the lower side of the front shock absorber.
Clean the installation surfaces of the front shock absorber and the steering knuckle.
Temporarily install the 2 nuts (Step A).
![]() |
Fully push or pull the front axle hub in the direction of the required adjustment (Step B).
Tighten the nuts.
Install the front wheel.
![]() ![]() ![]() |
Check the camber.
If the measured value is not within the specification, calculate the required adjustment amount using the formula below.
Camber adjustment amount = Specified range center - measured value
Check the combination of installed bolts. Select appropriate bolts from the table below to adjust the camber to the specified values.
| Move the axle toward (+) in step (B) | Move the axle toward (-) in step (B) |
| Refer to table (1) (Move the axle toward positive side) | Refer to table (2) (Move the axle toward negative side) |
Repeat the steps mentioned above. In step (A), replace 1 or 2 selected bolts.
| 8. FRONT WHEELS FACING STRAIGHT AHEAD |
| 9. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL (w/ VSC) |
| 10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ VSC) |
| 11. PERFORM YAW RATE SENSOR ZERO POINT CALIBRATION (w/ VSC) |
| 12. CHECK STEERING ANGEL SENSOR ZERO POINT (w/ VSC) |