Home › SUSPENSION & AXLE › SUSPENSION › REAR NO. 1 SUSPENSION ARM

REAR NO. 1 SUSPENSION ARM > REMOVAL

for Preparation Click here


NOTICE:
Check if an old gasket still remains on the pipe. If so, remove it. Also, check if any bolts or nuts are rusted. If so, replace them.



1. REMOVE REAR WHEEL


2. REMOVE CENTER EXHAUST PIPE ASSEMBLY (for 2AZ-FE)


  1. Remove the 2 bolts, 2 nuts and center exhaust pipe assembly.


    A135690E01

  1. Remove the gasket from the front exhaust pipe.



3. REMOVE TAIL EXHAUST PIPE ASSEMBLY (for 2GR-FE)


  1. Remove the 4 nuts and 2 exhaust tail pipes.


    A135718

  1. Remove the 2 gaskets from the exhaust tail pipes.



4. REMOVE CENTER EXHAUST PIPE ASSEMBLY (for 2GR-FE)


  1. Remove the 2 bolts, 2 nuts and exhaust center pipe assembly.


    A135719

  1. Remove the gasket from the exhaust center pipe assembly.



5. SEPARATE REAR STABILIZER LINK ASSEMBLY LH


    C138763
  1. Remove the nut and separate the rear stabilizer link assembly LH (lower side) from the rear stabilizer bar.

    HINT:
    If the ball joint turns together with the nut, use a hexagon wrench (5 mm) to hold the stud.



6. SEPARATE REAR STABILIZER LINK ASSEMBLY RH

HINT:
Separate the RH side using the same procedures as for the LH side.



7. REMOVE REAR STABILIZER BAR NO. 2 BRACKET


    C139014
  1. Remove the 2 bolts and rear stabilizer bar No. 2 bracket.



8. REMOVE REAR STABILIZER BAR NO. 1 BRACKET


    C139015
  1. Remove the 2 bolts and rear stabilizer bar No. 1 bracket.



9. REMOVE REAR STABILIZER BAR


10. REMOVE REAR STABILIZER BUSHING
  1. Remove the 2 rear stabilizer bushings from the rear stabilizer bar.



11. SEPARATE REAR STRUT ROD


    C132459E01
  1. Support the rear axle carrier with a jack.



    C132476
  1. Remove the bolt and nut, and disconnect the strut rod (front side).

    NOTICE:
    When removing the bolt, keep the nut from rotating.



    C132476
  1. Remove the bolt, nut and strut rod from the rear axle carrier.

    NOTICE:
    When removing the bolt, keep the nut from rotating.



12. SEPARATE REAR NO. 2 SUSPENSION ARM LH


    C132478
  1. Remove the bolt, nut and separate the rear suspension No. 2 arm (outer side) from the rear axle carrier.

    NOTICE:
    When removing the bolt, keep the nut from rotating.



13. SEPARATE REAR NO. 2 SUSPENSION ARM RH

HINT:
Separate the RH side using the same procedures as for the LH side.



14. SEPARATE REAR NO. 1 SUSPENSION ARM LH


    C132479
  1. Remove the bolt, nut and the rear No. 1 suspension arm (outer side) from the rear axle carrier.

    NOTICE:
    When removing the bolt, keep the nut from rotating.



15. SEPARATE REAR NO. 1 SUSPENSION ARM RH

HINT:
Separate the RH side using the same procedures as for the LH side.



16. REMOVE REAR SUSPENSION MEMBER LOWER STOPPER LH


    C132500
  1. Remove the 2 nuts and the rear suspension member lower stopper LH.



17. REMOVE REAR SUSPENSION MEMBER LOWER STOPPER RH


    C138862
  1. Remove the 2 nuts and the rear suspension member lower stopper RH.



18. REMOVE REAR SUSPENSION MEMBER SUB-ASSEMBLY


    C132502
  1. Support the rear suspension member with a jack.

  1. Remove the 2 bolts, and the rear suspension member sub-assembly.



19. REMOVE REAR NO. 1 SUSPENSION ARM LH


    B053744E01
  1. Remove the bolt and rear No. 1 suspension arm assembly LH.