NAVIGATION SYSTEM > Illumination Circuit |

| 1.CHECK ILLUMINATION |
Check if the illumination for the navigation receiver assembly, steering pad switch, glove box or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the tail or head position.
| Result | Proceed to |
| Illumination comes on for all components except steering pad switch. | A |
| Illumination comes on for all components except navigation receiver assembly. | B |
| No illumination comes on (navigation receiver assembly, hazard switch, glove box, etc.). | C |
| Illumination comes on for all components except navigation receiver assembly and steering pad switch. | D |
|
| ||||
|
| ||||
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (BATTERY - SPIRAL CABLE) |
![]() |
Disconnect the spiral cable connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| E18-12 (IL+2) - Body ground | Light control switch in tail or head | 11 to 14 V |
| *1 | Front view of wire harness connector (to Spiral Cable) |
|
| ||||
| OK | |
| 3.INSPECT SPIRAL CABLE |
![]() |
Disconnect the steering pad switch and spiral cable connectors.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| a1-8 (EAU) - E18-4 (EAU) | Center | Below 1 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right | ||
| a1-5 (IL+2) - E18-12 (IL+2) | Center | Below 1 Ω |
| 2.5 rotations to the left | ||
| 2.5 rotations to the right |
| *1 | Component without harness connected (Spiral Cable) |
| *2 | Steering Pad Switch Side |
| *3 | Vehicle Side |
|
| ||||
| OK | |
| 4.INSPECT STEERING PAD SWITCH ASSEMBLY |
Disconnect the steering pad switch assembly connector.
Connect a positive (+) lead to terminal IL+2 and a negative (-) lead to terminal EAU of the steering pad switch connector.

Check if the illumination for the steering pad switch comes on.
| *1 | Component without harness connected (Steering Pad Switch Assembly) |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - NAVIGATION RECEIVER) |
![]() |
Disconnect the navigation receiver assembly connector.
![]() |
Disconnect the spiral cable connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F24-6 (SWG) - E18-4 (EAU) | Always | Below 1 Ω |
| F24-6 (SWG) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Navigation Receiver Assembly) |
| *2 | Front view of wire harness connector (to Spiral Cable) |
|
| ||||
| OK | ||
| ||
| 6.CHECK HARNESS AND CONNECTOR (BATTERY - NAVIGATION RECEIVER ASSEMBLY) |
![]() |
Disconnect the navigation receiver assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F27-10 (ILL+) - Body ground | Light control switch in tail or head | 11 to 14 V |
| *1 | Front view of wire harness connector (to Navigation Receiver Assembly) |
|
| ||||
| OK | ||
| ||
| 7.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT) |
![]() |
Disconnect the navigation receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F27-7 (GND) - Body ground | Always | 10 kΩ or higher |
| *1 | Front view of wire harness connector (to Navigation Receiver Assembly) |
|
| ||||
| OK | ||
| ||