Home › BODY ELECTRICAL › NAVIGATION › NAVIGATION SYSTEM

NAVIGATION SYSTEM > Illumination Circuit

for Preparation Click here


DESCRIPTION

Power is supplied to the navigation receiver assembly and steering pad switch illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM


E185813E01


INSPECTION PROCEDURE

NOTICE:
The vehicle is equipped with an SRS (Supplemental Restraint System). Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (Click here).

1.CHECK ILLUMINATION
  1. Check if the illumination for the navigation receiver assembly, steering pad switch, glove box or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the tail or head position.

    Result:

    Result
    Proceed to
    Illumination comes on for all components except steering pad switch.
    A
    Illumination comes on for all components except navigation receiver assembly.
    B
    No illumination comes on (navigation receiver assembly, hazard switch, glove box, etc.).
    C
    Illumination comes on for all components except navigation receiver assembly and steering pad switch.
    D



B
Go to step 6

C
GO TO LIGHTING SYSTEM (Click here)

D
Go to step 7
A


2.CHECK HARNESS AND CONNECTOR (BATTERY - SPIRAL CABLE)


    E168579E12
  1. Disconnect the spiral cable connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E18-12 (IL+2) - Body ground
    Light control switch in tail or head
    11 to 14 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Spiral Cable)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT SPIRAL CABLE


    E168547E09
  1. Disconnect the steering pad switch and spiral cable connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    a1-8 (EAU) - E18-4 (EAU)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    a1-5 (IL+2) - E18-12 (IL+2)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right

    NOTICE:
    The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Refer to the pages shown in the brackets.

    HINT:
    1. Removal (Click here)
    2. Installation (Click here)

    Text in Illustration 
    *1
    Component without harness connected
    (Spiral Cable)
    *2
    Steering Pad Switch Side
    *3
    Vehicle Side



NG
REPLACE SPIRAL CABLE (Click here)
OK


4.INSPECT STEERING PAD SWITCH ASSEMBLY
  1. Disconnect the steering pad switch assembly connector.



  1. Connect a positive (+) lead to terminal IL+2 and a negative (-) lead to terminal EAU of the steering pad switch connector.


    E185620E01

  1. Check if the illumination for the steering pad switch comes on.

    OK:
    Illumination for the steering pad switch assembly comes on.

    Text in Illustration 
    *1
    Component without harness connected
    (Steering Pad Switch Assembly)



NG
REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - NAVIGATION RECEIVER)


    E168561E24
  1. Disconnect the navigation receiver assembly connector.



    E168579E15
  1. Disconnect the spiral cable connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F24-6 (SWG) - E18-4 (EAU)
    Always
    Below 1 Ω
    F24-6 (SWG) - Body ground
    Always
    10 kΩ or higher

Text in Illustration 
*1
Front view of wire harness connector
(to Navigation Receiver Assembly)
*2
Front view of wire harness connector
(to Spiral Cable)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

6.CHECK HARNESS AND CONNECTOR (BATTERY - NAVIGATION RECEIVER ASSEMBLY)


    E168564E14
  1. Disconnect the navigation receiver assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F27-10 (ILL+) - Body ground
    Light control switch in tail or head
    11 to 14 V

Text in Illustration 
*1
Front view of wire harness connector
(to Navigation Receiver Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

7.CHECK HARNESS AND CONNECTOR (GROUND CIRCUIT)


    E168564E15
  1. Disconnect the navigation receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F27-7 (GND) - Body ground
    Always
    10 kΩ or higher

Text in Illustration 
*1
Front view of wire harness connector
(to Navigation Receiver Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)