Home › BODY ELECTRICAL › LIGHTING › LIGHTING SYSTEM

DTC    B1244    Light Sensor Circuit Malfunction

for Preparation Click here


DESCRIPTION

The automatic light control sensor detects ambient light, converts it into an electrical signal, and outputs it to the main body ECU. The main body ECU turns on or off the headlights and taillights according to the signal.

DTC No.
DTC Detecting Condition
Trouble Area
B1244
  1. Malfunction in automatic light control sensor
  2. Open or short in automatic light control sensor circuit
  1. Automatic light control sensor
  2. Harness or connector
  3. Main body ECU (Instrument panel J/B)

WIRING DIAGRAM


E124321E05


INSPECTION PROCEDURE

1.READ VALUE USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to the ON position and turn the intelligent tester main switch on.

  1. Select the item below in the DATA LIST, and read the display on the intelligent tester.

    Main Body (Main Body ECU): 
    Item
    Measurement Item / Display (Range)
    Normal Condition
    Diagnostic Note
    Illumination Rate Info
    Illumination rate information / 0 ms. to 99.99 ms.
    0.8 ms. to 22.0 ms. (Value is output according to ambient illuminance)
    -

    OK:
    Normal condition listed above is displayed.



OK
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
NG


2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - AUTOMATIC LIGHT CONTROL SENSOR)


    E121476E04
  1. Disconnect the E11 automatic light control sensor connector.

  1. Disconnect the E6 main body ECU connector.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E6-18 (CLTE) - E11-3 (CLTE)
    Always
    Below 1 Ω
    E6-19 (CLTS) - E11-5 (CLTS)
    Always
    Below 1 Ω
    E6-20 (CLTB) - E11-6 (CLTB)
    Always
    Below 1 Ω
    E6-18 (CLTE) - Body ground
    Always
    10 kΩ or higher
    E6-19 (CLTS) - Body ground
    Always
    10 kΩ or higher
    E6-20 (CLTB) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT MAIN BODY ECU (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY )
  1. Reconnect the main body ECU connector.



    B109993E16
  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    E11-6 (CLTB) - E11-3 (CLTE)
    Ignition switch off
    Below 1 V
    E11-6 (CLTB) - E11-3 (CLTE)
    Ignition switch ON
    10 to 14 V

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    E11-3 (CLTE) - Body ground
    Always
    Below 1 Ω



NG
REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
OK


4.INSPECT AUTOMATIC LIGHT CONTROL SENSOR


    E121468E04
  1. Reconnect the automatic light control sensor connector.

  1. Connect an oscilloscope to the automatic light control sensor connector.



    B113714E01
  1. Check the waveform.

    OK:
    Tester Connection
    Tool Setting
    Condition
    Specified Condition
    E11-3 (CLTE) - E11-5 (CLTS)
    5 V/DIV., 5 ms./DIV.
    Ignition switch ON, light control switch in AUTO
    Correct waveform is as shown

    HINT:
    If the ambient light becomes brighter, width A becomes narrower.



NG
REPLACE AUTOMATIC LIGHT CONTROL SENSOR
OK

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY