REAR DOOR > DISASSEMBLY |
| 1. REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG |
![]() |
Using a screwdriver with the tip wrapped with protective tape, disengage the 3 claws and remove the rear door inside handle bezel plug.
| 2. REMOVE DOOR ASSIST GRIP COVER |
![]() |
Using a screwdriver with the tip wrapped with protective tape, disengage the 6 claws and remove the door assist grip cover.
| 3. REMOVE REAR ASH RECEPTACLE ASSEMBLY |
![]() |
Remove the rear ash receptacle assembly.
| 4. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY |
![]() |
Remove the 3 screws.
Using a clip remover, disengage the 7 clips.
![]() |
Raise the rear door trim board to disengage the 4 claws and remove the rear door trim board together with the rear door inner glass weatherstrip.
Disconnect the connector.
![]() |
Disengage the 2 claws and disconnect the rear door inside handle sub-assembly.
![]() |
Disengage the clip as shown in the illustration and remove the No. 1 door scuff plate clamp from the rear door trim board.
| 5. REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY |
Disconnect the connector.
![]() |
Using a screwdriver with the tip wrapped with protective tape, disengage the 2 claws and remove the rear power window regulator switch assembly.
| 6. REMOVE REAR DOOR INNER GLASS WEATHERSTRIP |
![]() |
Disengage the 3 clips as shown in the illustration and remove the rear door inner glass weatherstrip from the rear door trim board.
| 7. REMOVE REAR DOOR ARMREST BASE PANEL UPPER |
![]() |
Remove the 7 screws.
Disengage the 4 claws and remove the rear door armrest base panel upper.
| 8. REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY |
![]() |
Disconnect the cables and remove the rear door inside handle sub-assembly.
| 9. REMOVE REAR DOOR INSIDE PANEL REINFORCE |
![]() |
Remove the 4 screws and the rear door inside panel reinforce.
Remove the 4 grommets.
| 10. REMOVE REAR DOOR SERVICE HOLE COVER |
![]() |
Disconnect the connector.
Remove the rear door service hole cover.
| 11. REMOVE REAR DOOR CHECK ASSEMBLY |
![]() |
Remove the 3 bolts and the rear door check assembly.
| 12. REMOVE REAR DOOR WEATHERSTRIP |
![]() |
Using a clip remover, disengage the 20 clips and remove the rear door weatherstrip.
| 13. REMOVE REAR DOOR GLASS RUN |
![]() |
Remove the rear door glass run.
| 14. REMOVE REAR DOOR FRAME GARNISH |
![]() |
Disengage the clip and remove the rear door frame garnish.
| 15. REMOVE REAR DOOR LOWER WINDOW FRAME SUB-ASSEMBLY |
![]() |
Remove the 2 bolts, the screw, and the rear door lower window frame sub-assembly.
| 16. REMOVE REAR DOOR QUARTER WINDOW GLASS |
![]() |
Remove the rear door quarter window glass and the rear door quarter window weatherstrip as a unit as shown in the illustration.
Remove the rear door quarter window glass from the rear door quarter window weatherstrip.
| 17. REMOVE REAR DOOR GLASS SUB-ASSEMBLY |
![]() |
Remove the rear door glass sub-assembly from the rear door window regulator sub-assembly as shown in the illustration.
| 18. REMOVE REAR DOOR WINDOW REGULATOR SUB-ASSEMBLY |
![]() |
Disconnect the connector.
Loosen the temporary bolt.
Remove the 3 bolts.
Remove the rear door window regulator sub-assembly and the power window regulator motor assembly rear as a unit.
Remove the temporary bolt from the rear door window regulator.
| 19. REMOVE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY |
![]() |
Using a "TORX" driver (T25), remove the 3 screws and the rear power window regulator motor assembly.
| 20. REMOVE REAR DOOR LOCK ASSEMBLY |
![]() |
Using a "TORX" socket wrench (T30), remove the 3 screws.
Move the rear door lock assembly downward and pull the release plate out of the rear door outside handle frame.
Remove the door lock wiring harness seal from the rear door lock assembly.
| 21. REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY |
![]() |
Using a screwdriver, disengage the claw.
![]() |
Remove the rear door lock remote control cable assembly.
| 22. REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY |
![]() |
Using a screwdriver, disengage the 3 claws.
![]() |
Remove the rear door inside locking cable assembly.
| 23. REMOVE REAR DOOR OUTSIDE HANDLE COVER |
![]() |
Using a "TORX" socket wrench (T30), loosen the screw.
![]() |
Disengage the 2 claws and remove the rear door outside handle cover.
| 24. REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY |
![]() |
Pull and hold the release plate of the outside handle frame as shown in the illustration.
![]() |
Remove the rear door outside handle assembly as shown in the illustration.
| 25. REMOVE REAR DOOR FRONT OUTSIDE HANDLE PAD |
![]() |
Disengage the 3 claws and remove the rear door front outside handle pad.
| 26. REMOVE REAR DOOR REAR OUTSIDE HANDLE PAD |
![]() |
Disengage the 2 claws and remove the rear door rear outside handle pad.
| 27. REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY |
![]() |
Using a "TORX" socket wrench (T30), remove the screw.
Disengage the claw and remove the rear door outside handle frame sub-assembly.
| 28. REMOVE REAR DOOR BELT MOULDING ASSEMBLY |
![]() |
Fully open the rear door glass.
Put protective tape around the rear door belt moulding assembly.
![]() |
Using a moulding remover, disengage the clip and 6 claws, and remove the rear door belt moulding assembly.
| 29. REMOVE REAR DOOR FRONT WINDOW FRAME MOULDING |
| Item | Temperature |
| Vehicle Body | 40 to 60°C (104 to 140°F) |
| Moulding | 20 to 30°C (68 to 86°F) |
Using a heat light, heat the rear door front window frame moulding.
![]() |
Disengage the clip.
![]() |
Using a moulding remover, remove the rear door front window frame moulding.
| 30. REMOVE REAR DOOR UPPER WINDOW FRAME MOULDING |
![]() |
Put a 4 mm (0.16 in.) drill bit into a drill.
Tape the drill bit without the portion of 5 mm (0.20 in.) from the tip covered.
Lightly press the drill bit against the rivets, drill off the flanges of the rivets, and remove the 7 rivets.
Using a vacuum cleaner, remove the rivet fragments and shavings from the drilled areas.
Remove the rear door upper window frame moulding from the door frame.
| 31. REMOVE REAR DOOR OUTSIDE STRIPE |
Using a heat light, heat the rear door outside stripe.
| Item | Temperature |
| Vehicle Body | 40 to 60°C (104 to 140°F) |
Pull back an edge of the rear door outside stripe and pull it parallel to the vehicle body to pull it off.
| 32. REMOVE REAR DOOR LOWER OUTSIDE STRIPE |
Using a heat light, heat the rear door lower outside stripe.
| Item | Temperature |
| Vehicle Body | 40 to 60°C (104 to 140°F) |
Pull back an edge of the rear door lower outside stripe and pull it parallel to the vehicle body to pull it off.