Home › BODY ELECTRICAL › DOOR LOCK › POWER DOOR LOCK CONTROL SYSTEM

POWER DOOR LOCK CONTROL SYSTEM > Front Passenger Side Door UNLOCK Detection Switch Circuit

for Preparation Click here


DESCRIPTION

The front passenger door unlock detection switch is built into the front passenger door lock assembly. The switch turns on when the front passenger door is locked and turns off when the door is unlocked.
The main body ECU is connected to the front passenger door lock assembly via terminal LSWP and front passenger door lock/unlock state signals are input to the ECU.
The main body ECU applies voltage to the door unlock detection switch via terminal LSWP. When the door unlock detection switch is on (there is continuity between the switch terminals), a lock state signal is input to the ECU. When the switch is off (there is no continuity between the switch terminals), an unlock state signal is input.

WIRING DIAGRAM


B109773E37


INSPECTION PROCEDURE

1.READ VALUE USING DATA LIST (DOOR UNLOCK DETECTION SWITCH)
  1. Check the DATA LIST to ensure proper function of the door unlock detection switch.

    Main Body: 
    Item
    Measurement Item /
    Display (Range)
    Normal Condition
    Diagnostic Note
    P-Door Lock Pos SW
    Passenger side door lock position switch signal
    /ON or OFF
    ON: Passenger side door lock is in UNLOCK position
    OFF: Passenger side door lock is in LOCK position
    -

    OK:
    The display is as specified in the normal condition column.



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE 

2.INSPECT FRONT DOOR LOCK ASSEMBLY (DOOR UNLOCK DETECTION SWITCH)


    B065429E23
  1. Inspect LHD models.

    1. Remove the front door lock assembly RH.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Measurement Condition
      Door Lock Condition
      Specified Condition
      7 - 8
      Battery positive (+) → Terminal 4
      Battery negative (-) → Terminal 1
      Lock
      10 kΩ or higher
      7 - 8
      Battery positive (+) → Terminal 1
      Battery negative (-) → Terminal 4
      Unlock
      Below 1 Ω



    B065427E22
  1. Inspect RHD models.

    1. Remove the front door lock assembly LH.

    2. Measure the resistance according to the value(s) in the table below.

      Standard resistance:
      Tester Connection
      Measurement Condition
      Door Lock Condition
      Specified Condition
      7 - 8
      Battery positive (+) → Terminal 4
      Battery negative (-) → Terminal 1
      Lock
      10 kΩ or higher
      7 - 8
      Battery positive (+) → Terminal 1
      Battery negative (-) → Terminal 4
      Unlock
      Below 1 Ω



NG
REPLACE FRONT DOOR LOCK ASSEMBLY
OK


3.CHECK WIRE HARNESS (FRONT DOOR LOCK ASSEMBLY - MAIN BODY ECU)


    B111708E13
  1. Disconnect the front door lock assembly connector.

  1. Disconnect the ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    (Symbols)
    Condition
    Specified Condition
    (*1) M8-7 (LSSR) - E6-27 (LSWP)
    Always
    Below 1 Ω
    (*1) M8-7 (LSSR) - Body ground
    Always
    10 kΩ or higher
    (*1) M8-8 (E) - Body ground
    Always
    Below 1 Ω
    (*2) I7-8 (LSSR) - E6-27 (LSWP)
    Always
    Below 1 Ω
    (*2) I7-8 (LSSR) - Body ground
    Always
    10 kΩ or higher
    (*2) I7-7 (E) - Body ground
    Always
    Below 1 Ω

    *1: LHD
    *2: RHD



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU