AUTOMATIC TRANSAXLE FLUID > ADJUSTMENT |
| 1. PRECAUTIONS AND WORK DESCRIPTION |
The U660E automatic transaxle does not have an oil filler tube and oil level gauge. When adding fluid, add fluid through the refill hole on the transaxle case. The fluid level can be adjusted by draining excess fluid (allowing excess fluid to overflow) through the overflow tube of the oil pan.
Before adjusting the fluid level, add the specified amount of fluid when the engine is cold and warm up the engine to circulate the fluid in the transaxle. Ensure that the fluid temperature is as specified and the engine is idling.

The U660E automatic transaxle requires Toyota Genuine ATF WS.
The adjustment should be performed according to the procedures and notes.
| 2. WORK FLOW |
The adjustment should be performed according to the procedures referring to the work flow below.

| 3. BEFORE FILLING TRANSAXLE WITH FLUID |
Lift the vehicle.
Remove the engine under covers RH and LH, and fender apron seal LH.
| 4. PERFORM INITIAL FILLING |
![]() |
Remove the refill plug and gasket from the automatic transaxle.
| Operation that does not require initial filling |
|
![]() |
Using a 6 mm socket hexagon wrench, remove the overflow plug and gasket from the automatic transaxle.
![]() |
Using a 6 mm socket hexagon wrench, check that the overflow tube is tightened to the specified torque.
Perform initial filling
![]() |
Fill the transaxle through the refill hole until fluid begins to trickle out of the overflow plug hole.
![]() |
Wait until the fluid flow slows and only drips come out.
![]() |
Temporarily install the overflow plug.
| 5. ADD SPECIFIED AMOUNT |
Fill the transaxle with the correct amount of fluid as listed in the table below.
| Performed Repair | Fill Amount |
| 0.5 liters (0.5 US qts, 0.4 lmp. qts) |
| 2.8 liters (3.0 US qts, 2.5 lmp. qts) |
| Removal and installation of valve body | 3.2 liters (3.4 US qts, 2.8 lmp. qts) |
| Removal and installation of transaxle (not remove torque converter) | 3.4 liters (3.6 US qts, 3.0 lmp. qts) |
| Removal and installation of torque converter (torque converter reused) | 4.8 liters (5.1 US qts, 4.2 lmp. qts) |
| Replacement of a new torque converter | 5.3 liters (5.6 US qts, 4.7 lmp. qts) |
![]() |
Temporarily install the refill plug to avoid fluid splash.
Lower the vehicle.
| 6. ADJUST FLUID TEMPERATURE |
When using the intelligent tester:
Connect the intelligent tester to the DLC3 with the ignition switch off.
Turn the ignition switch ON and turn the intelligent tester main switch ON.
Enter the following menus: Power train / Engine / Active Test / Connect the TC and TE1.
Select the date list menu: A/T Oil Temp from ECT.
Check A/T OIL TEMP.
Push the active test menu: Connect the TC and TE1/ ON.
Depress and hold down the brake pedal.
Start the engine.
Slowly move the shift lever from P to D, then back to P.
![]() |
While observing the D shift indicator on the combination meter, move the shift lever back and forth between N and D at an interval of 1.5 seconds for 6 seconds or more.
Check that the D shift indicator comes on for 2 seconds.
Move the shift lever from N to P.
Release the brake pedal.
Push the active test menu: Connect the TC and TE1/ OFF
Warm up the engine with the engine idling until the fluid temperature reaches the normal operating temperature (40 to 45°C [104 to 113°F]).
| Below Normal Operating Temperature | Normal Operating Temperature | Above Normal Operating Temperature |
| 40°C or less (104°F or less) | 40 to 45°C (104 to 113°F) | 45°C or more (113°F or more) |
![]() |
| Below Normal Operating Temperature (40°C or less) (104°F or less) | Normal Operating Temperature (40 to 45°C) (104 to 113°F) | Above Normal Operating Temperature (45°C or more) (113°F or more) |
| OFF | ON | Blinks |
When not using the intelligent tester:
![]() |
Using SST, connect terminals 13 (TC) and 4 (CG) of the DLC3 with the ignition switch off.
Depress and hold down the brake pedal.
Start the engine.
Slowly move the shift lever from P to D, then back to P.
![]() |
While observing the D shift indicator on the combination meter, move the shift lever back and forth between N and D at an interval of 1.5 seconds for 6 seconds or more.
Check that the D shift indicator comes on for 2 seconds.
Move the shift lever from N to P.
Release the brake pedal.
![]() |
Remove SST from terminals 13 (TC) and 4 (CG).
![]() |
Allow the engine to idle until the D shift indicator comes on again.
| Below Normal Operating Temperature (40°C or less) (104°F or less) | Normal Operating Temperature (40 to 45°C) (104 to 113°F) | Above Normal Operating Temperature (45°C or more) (113°F or more) |
| OFF | ON | Blinks |
| 7. ADJUST FLUID LEVEL |
Lift the vehicle.
Adjust fluid level
![]() |
Using a 6 mm socket hexagon wrench, remove the overflow plug and gasket.
Check the amount of fluid that comes out of the overflow plug hole.
![]() |
If the amount of fluid that comes out of the overflow hole is large, wait until the fluid flow slows and only drips come out.
![]() |
If no fluid comes out of the overflow hole, remove the refill plug and gasket. Then add transaxle fluid through the refill hole until fluid comes out of the overflow hole. Wait until the fluid flow slows and only drips come out.
![]() |
Check that the fluid flow has slowed and only drips come out.
![]() |
Install the overflow plug with a new gasket.
![]() |
Install the refill plug with a new gasket.
Lower the vehicle.
Turn the ignition switch OFF.
Remove the intelligent tester form DLC3 (when using the intelligent tester).
| 8. AFTER FILLING TRANSMISSION |
Lift the vehicle.
Clean each part.
Check the fluid leak.
Install the fender apron seal LH, engine under cover RH, and LH.
Lower the vehicle.